Search Results

The rotor and stator of electric motors consist of multiple materials, of which steel forms the majority of mass and volume. Steel in electric motors is commonly in the form of thin sheets (laminations), stacked along the axis of the rotor. The structural integrity of such a stack can be ensured using bolting, welding or bonding of the laminations. Predictive mechanical finite element simulations of these laminated stacks can become computationally intense because the steel sheets are thin, and the motor often contains hundreds of them. If the laminations are modelled individually, the size of the elements is very small compared to the overall dimensions and the interface between the laminations need to be modelled as well. In this paper, we present an alternate method of modelling this laminated stack as a single solid body using homogeneous and orthotropic material property, instead of representing each lamination.

The modern luxurious electric vehicle (EV) demands high torque and high-speed requirements with increased range. Fulfilling these requirements gives rise to the need for increased efficiency and power density of the motors in the Electric Drive Unit (EDU). Internal Permanent Magnet (IPM) motor is one of the best suited options in such scenarios because of its primary advantages of higher efficiency and precise control over torque and speed. In the IPM motor, permanent magnets are mounted within the rotor body to produce a resultant rotating magnetic field with the 3-phase AC current supply in the stator. IPM configuration provides structural integrity and high dynamic performance as the magnets are inserted within the rotor body. Adhesive glue is used to install the magnets within the laminated stack of rotor.

The reduction in wind noise is increasingly important to vehicle designers as overall vehicle refinement increases. Customers often fit accessories such as roof bars to vehicles, with the aerodynamic interaction of these components generating aeroacoustic noise sources. These are often tonal in nature and of particular annoyance to occupants. Sensors for automated driving fitted to future vehicles may also have a similar detrimental effect on vehicle refinement. Therefore, careful design of such components is important to minimise dissatisfaction. This paper presents the combined application of acoustic beamforming in a full-scale aeroacoustic wind tunnel and the use of a Lattice Boltzmann Method CFD code to characterise the aeroacoustic performance of a roof bar design when fitted to a production vehicle.

Micro-mobility vehicles such as electric scooters and bikes are increasingly used for urban transportation; their designs usually trade off performance and range. Addressing thermal and cooling issues in such vehicles could enhance performance, reliability, life, and range. Limited packaging space within the wheels precludes the use of complex cooling systems that would also increase the cost and complexity of these mass-produced wheel motors. The present study begins by evaluating the external aerodynamics of the scooter to characterise the airflow conditions near the rotating wheel; then, a steady-state conjugate heat transfer model of a commercially available wheel hub motor (500W) is created using commercial computational fluid dynamics (CFD) software, StarCCM+. The CAD model of the motor used for this analysis has an external rotor permanent magnet (PM) brushless DC topology.

Engine downsizing is one the most common methods of coping with strict emission regulations. However, it must be coupled with complementary systems so that the engine performance would meet the standards. That is why new efficient solutions can pave the way toward this goal. The electric forced-induction system (EFIS) is the emerging replacement for conventional forced-induction systems (FIS), namely, turbochargers and superchargers. The reason behind this replacement is the drawbacks associated with FIS, among them are turbo lag and inefficiency in exhaust gas energy recycling. Electrically split turbocharger (EST) is a form of EFIS which offers a great potential for engine downsizing. In this paper, a new approach to EST utilization for lowering the fuel consumption (FC) without compromising performance has been introduced, through which the augmented degree of freedom enabled by an EST is used to optimize the air-charge boosting.

Hybrid technologies enable the reduction of noxious tailpipe emissions and conformance with ever-decreasing allowable homologation limits. The complexity of the hybrid powertrain technology leads to an energy management problem with multiple energy sinks and sources comprising the system resulting in a high-dimensional time dependent problem for which many solutions have been proposed. Methods that rely on accurate predictions of potential vehicle operations are demonstrably more optimal when compared to rule-based methodology [1]. In this paper, a previously proposed energy management strategy based on an offline optimization using dynamic programming is investigated. This is then coupled with an online model predictive control strategy to follow the predetermined optimal battery state of charge trajectory prescribed by the dynamic program.

The emergence of additive manufacturing (AM) technology has enabled the internal cooling channel layout for high pressure aluminium die casting (HPADC) tools to be designed and modified without topological constraint. Optimisation studies of a full industrial HPADC mould for extending the tool service life has received limited attention due to the high geometrical complexity and the various physics with multi time- and length- scales in addition to the manufacturability limitations. In this work, a new computationally efficient algorithm that employs the adjoint optimisation method has been developed to optimise the coolant channels layout in a complete mould with various 3D printed inserts. The algorithms significantly reduced the computational time and resources by decoupling the fluid flow in the coolant channels from the tool and simulating them separately.

The Range Rover Evoque is a compact luxury SUV, first introduced by Land Rover in 2012. Almost 800,000 units of the first-generation vehicle were sold. This paper explores some of the challenges entailed in developing the next generation of this successful product, maintaining key design cues while at the same time improving its aerodynamic efficiency. A development approach is outlined that made use of both numerical simulation and full-scale moving ground wind tunnel testing. A drag coefficient of 0.32 was obtained for the best derivative by paying particular attention to: the integration of active grille shutters; the front bumper and tyre package; brake cooling; underfloor design; wake control strategy; and detail optimization. This approach delivered the most aerodynamic Range Rover at the time of its introduction. The impact of these design changes on the aerodynamic flow field and consequently drag is highlighted.

The aerodynamic effects of bodies in close proximity continues to be an interest for those involved in aeronautical, automotive and civil engineering together with those involved in sports such as cycling, motor racing and sailing. For passenger cars, research in the USA published in the 1980s had considered travelling in close proximity, termed “platooning”, as a means for reducing congestion. But the aerodynamic drag reduction and fuel-savings found in associated wind tunnel tests and road-trials became the focus of further investigations. Although practical applications were not originally pursued, the recent development of control systems for connected and autonomous vehicles has provided the opportunity for platooning to be considered again within future traffic management systems.

Additive manufacturing (AM) provides significant geometric design freedom for the cooling of high pressure die casting (HPDC) tools. Designing cooling channels that can achieve a uniform temperature throughout the tool-cast interface during the moulding process can limit part warping and sink marks, internal part stresses, and increase tool life. However, the design of the embedded cooling channels requires high computational resources to model the heat transfer process for the cast, mould, and coolant from the moment aluminium is injected into the cavity until the injection for the next cycle. To enable the examination of the effect of various parameters, a simplified 3-D CFD conjugate heat transfer model is introduced by considering the experimental observations. The model decouples the cast part from the mould.

Lithium-ion batteries (LiBs) have been widely used in electrified vehicles, and the battery thermal management (BTM) system is needed to maintain the temperature that is critical to battery performance, safety, and health. Conventionally, three-dimensional battery thermal models are developed at the early stage to guide the design of the BTM system, in which battery thermophysical parameters (radial thermal conductivity, axial thermal conductivity, and specific heat capacity) are required. However, in most literature, those parameters were estimated with greatly different values (up to one order of magnitude). In this paper, an investigation is carried out to evaluate the magnitude of the influence of those parameters on the battery simulation results. The study will determine if accurate measurements of battery thermophysical parameters are necessary.

The work described in this paper is a continuation of an investigation into the effects of systematic changes in upper-body geometry on the aerodynamic drag of passenger-car-like bluff-body models in close longitudinal proximity and operating in platoon formations. The original work, presented in SAE paper 2019-01-0659, showed measurements of the aerodynamic drag of individual models within three-model platoons and for which each model was tested in three different upper-body configurations This provided a data-set of 27 platoon configurations to compare with the three baseline conditions of the isolated models. The work contrasted with other published platooning research in which the spacing, between homogeneous models in the platoons, was the only variable to be considered. In this publication the results of further wind tunnel tests, using the same models as before but in two-model platoons, providing a further 9 test configurations are compared with the original data.

Many modern vehicles have blunt rear end geometries for design aesthetics and practicality; however, such vehicles are potentially high drag. The application of tapering; typically applied to an entire edge of the base of the geometry is widely reported as a means of reducing drag, but in many cases, this is not practical on real vehicles. In this study side tapers are applied to only part of the side edge of a simplified automotive geometry, to show the effects of practical implementations of tapers. The paper reports on a parametric study undertaken in Loughborough University’s Large Wind Tunnel with the ¼ scale Windsor model equipped with wheels. The aerodynamic effect of implementing partial side edge tapers is assessed from a full height taper to a 25% taper in both an upper and lower body configuration. These were investigated using force and moment coefficients, pressure measurements and planar particle image velocimetry (PIV).

Whilst the primary function of the active grille shutters is to reduce the aerodynamic drag of the car, there are some secondary benefits like improving the warm up time of engine and also retaining engine heat when parked. In turbocharged IC engines the air is compressed (heated) in the turbo and then cooled by a low temperature cooling system before going into the engine. When the air intake temperature exceeds a threshold value, the engine efficiency falls - this drives the need for the cooling airflow across the radiator in normal operation. Airflow is also required to manage the convective heat transfer across various components in the engine bay for its lifetime thermal durability. Grill shutters can also influence the aerodynamic lift balance thus impacting the vehicle dynamics at high speed. The vehicle HVAC system also relies on the condenser in the front heat exchanger pack disposing the waste heat off in the most efficient way.

Predicting Exterior Water Management is important for developing vehicles that meet customer expectations in adverse weather. Fluid film methods, with Lagrangian tracking, can provide spray and surface water simulations for complex vehicle geometries in on-road conditions. To cope with this complexity and provide practical engineering simulations, such methods rely on empirical sub-models to predict phenomena such as the film stripping from the surface. Experimental data to develop and validate such models is difficult to obtain therefore here a high-fidelity Coupled Level-set Volume of Fluid (CLSVOF) simulation is carried out. CLSVOF resolves the interface of the liquid in three dimensions; allowing direct simulation of film behaviour and interaction with the surrounding air. This is used to simulate a simplified wing-mirror, with air flow, on which water is introduced.

This study presents a one-dimensional model for the prediction of the pressure loss across a wall-flow gasoline particulate filter (GPF). The model is an extension of the earlier models of Bissett [1] and Konstandopoulos and Johnson [2] to the turbulent flow regime, which may occur at high flow rates and temperatures characteristic of gasoline engine exhaust. A strength of the proposed model is that only one parameter (wall permeability) needs to be calibrated. An experimental study of flow losses for cold and hot flow is presented, and a good agreement is demonstrated. Unlike zero-dimensional models, this model provides information about the flow along the channels and thus can be extended for studies of soot and ash accumulation, heat transfer and reaction kinetics.

The potential benefit for passenger cars when travelling in a ‘platoon’ formation results from the total aerodynamic drag reduction which may result from the interaction of bluff bodies in close-proximity. In the 1980s this was considered as an opportunity to alleviate congestion and also for fuel-saving in response to the oil crises of the 1970s. Early interest was limited by the availability of suitable systems to control vehicle spacing. However, recent developments in communication and control technologies intended for connected and autonomous driving applications has provided the potential for ‘platooning’ to be incorporated within future traffic management systems. The study described in this paper uses a systematic approach to changes in vehicle shape in order to identify the sensitivity of the benefits of platooning to vehicle style.

The potential benefit for vehicles travelling in ‘platoon’ formations arises from a reduction in total aerodynamic drag which can result from the interaction of bluff bodies in close-proximity. During the 1980s this was considered as an opportunity to alleviate congestion and also for fuel-saving in response to the fuel crises of the 1970s. Early interest was limited partly due to the level of available control technology. But recent developments in vehicle-to-vehicle communication systems and autonomous driving technologies have provided the potential for platooning to be incorporated within future traffic management systems prompting renewed interest. For the investigation described in this paper, a new passenger car model was designed as the basis for determining the effectiveness of future low-drag styles in platoon formations. Small-scale models were tested in the Coventry University Wind Tunnel in platoons of up to 5 vehicles.

A prototype multi-hole diesel injector operating with n-heptane fuel from a high-pressure common rail system is used in a high-pressure and high-temperature test rig capable of reaching 1100 Kelvin and 150 bar under different oxygen concentrations. A novel optical set-up capable of visualizing the soot cloud evolution in the fuel jet from 30 to 85 millimeters from the nozzle exit with the high-speed color diffused back illumination technique is used as a result of the insertion of a high-pressure window in the injector holder opposite to the frontal window of the vessel. The experiments performed in this work used one wavelength provide information about physical of the soot properties, experimental results variating the operational conditions show the reduction of soot formation with an increase in injection pressure, a reduction in ambient temperature, a reduction in oxygen concentration or a reduction in ambient density.

Physical testing of a vehicle wading through water is performed to gauge its capability to traverse through shallow to deep levels of water, wherein various vehicle performance parameters are observed, recorded and analysed. Jaguar Land Rover (JLR) has instigated and established a comprehensive CAE test procedure for assessing the same, which makes use of overset mesh (in a CFD environment) for a non-traditional approach to vehicle motion. The paper presents investigations made into the established wading physics, in order to optimise the splashing and water jet modelling. Large Scale Interface model was implemented instead of the previously standardised VOF-VOF fluid phase interaction model, and a comparison is made between the two. The implemented wheel rotation approach was scrutinised as well and appropriate inferences are drawn.