Search Results

The steer-by-wire (SBW) system, an integral component of the drive-by-wire chassis responsible for controlling the lateral motion of a vehicle, plays a pivotal role in enhancing vehicle safety. However, it poses a unique challenge concerning steering wheel return control, primarily due to its fundamental characteristic of severing the mechanical connection between the steering wheel and the turning wheel. This disconnect results in the inability to directly transmit the self-aligning torque to the steering wheel, giving rise to complications in ensuring a seamless return process. In order to realize precise control of steering wheel return, solving the problem of insufficient low-speed return and high-speed return overshoot of the steering wheel of the SBW system, this paper proposes a steering wheel active return control strategy for SBW system based on the backstepping control method.

To improve the braking energy recovery rate of pure electric garbage removal vehicles and ensure the braking effect of garbage removal vehicles, a strategy using particle swarm algorithm to optimize the regenerative braking fuzzy control of garbage removal vehicles is proposed. A multi-section front and rear wheel braking force distribution curve is designed considering the braking effect and braking energy recovery. A hierarchical regenerative braking fuzzy control strategy is established based on the braking force and braking intensity required by the vehicle. The first layer is based on the braking force required by the vehicle, based on the front and rear axle braking force distribution plan, and uses fuzzy controllers.

Based on the particularity of the racing field of the Baja SAE China, the Baja Racing Team of our university has adopted rzeppa universal joint for vehicle design and field competition in the semi-axle parts of the race car in previous years. In view of the complex conditions of the Baja Competition, such as gravity test, climb test, handling test, endurance test, etc., it is necessary to optimize and develop a more convenient maintenance model. Installation and use of better performance, more suitable for off-road conditions of the shaft. In this paper, based on the development dynamics of automobile axles and the transverse comparison of various axles, a kind of telescopic cross-shaft universal joint axles is designed by using CATIA software to model and simulate kinematics and dynamics by using ANSYS software. At the same time, the stress and strain of the model are continuously optimized according to the change of axle wheel Angle and the torque matching of Baja Racing.

Most of the skin injuries caused by traffic accidents, sports, falls, etc. are in the intermediate strain rate range (1-100s-1), and the injuries may occur at different sites, impact velocities, and orientations. To investigate the multifactorial mechanical properties of rat skin at intermediate strain rates, a three-factor, three-level experimental protocol was established using the standard orthogonal table L9(34), which includes site (upper dorsal, lower dorsal, and ventral side), strain rate (1s-1, 10s-1, and 100 s-1), and sampling orientation (0°, 45°, and 90° relative to the spine). Uniaxial tensile tests were performed on rat skin samples according to the protocol to obtain stress-stretch ratio curves. Failure strain energy was selected as the index, and the influence of each factor on these indexes, the differences between levels of each factor, and the influence of errors on the results were quantified by analysis of variance (ANOVA).

The active sound generation systems (ASGS) for electric vehicles (EVs) play an important role in improving sound perception and transmission in the car, and can meet the needs of different user groups for driving and riding experiences. The active sound synthesis algorithm is the core part of ASGS. This paper uses an efficient variable-range fast linear interpolation method to design a frequency-shifted and pitch-modified sound synthesis algorithm. By obtaining the operating parameters of EVs, such as vehicle speed, motor speed, pedal opening, etc., the original sound signal is interpolated to varying degrees to change the frequency of the sound signal, and then the amplitude of the sound signal is determined according to different driving states. This simulates an effect similar to the sound of a traditional car engine. Then, a dynamic superposition strategy is proposed based on the Hann window function.

Gear vibration and noise evaluation approaches are commonly proposed with a variety of way in a transmission system while complicated and obscured, it is difficult to provide a feasible basis for the gear development of E-drive system.

The technology of active sound generation (ASG) for automobiles is one of the most effective methods to flexibly achieve the sound design that meets the expectations of different user groups, and the active sound synthesis algorithms are crucial for the implementation of ASG. In this paper, the Kaiser window function-based the harmonic synthesis algorithm of automobile sound is proposed to achieve the extraction of the order sounds of target automobile. And, the suitable fitting functions are utilized to construct the mathematical model between the engine speed information and the amplitude of the different order sound. Then, a random phase correction algorithm is proposed to ensure the coherence of the synthesized sounds. Finally, the analysis of simulation results verifies that the established method of the extraction and synthesis of order sound can meet the requirements of target sound quality.

The multi-functional mechanical arm equipped on engineering vehicle can achieve different functions by installing different mechanism devices through the interface at the end of the mechanical arm. It can achieve functions like engineering construction and road rescue. Mechanical arm systems often work in complex environments, which requires good reliability and safety of the boom system. When the mechanical boom is working, the pressure of each luffing cylinder is large, and the contact force and acceleration of each boom are complex, which requires a certain degree of verification and optimization before it can be put into production. In this paper, a virtual prototype of a vehicle mounted hydraulic mechanical arm with four booms is established. Through ADAMS, the dynamic analysis of mechanical arm under multiple working conditions is carried out, the movement parameter changes and the pressure changes of each luffing cylinder are analyzed.

With the development of highway transportation and automobile industry technology, highway truck overload phenomenon occurs frequently, which poses a danger to road safety and personnel life safety. So it is very important to identify the overload phenomenon. Traditionally, static detection is adopted for overload identification, which has low efficiency. Aiming at this phenomenon, a dynamic overload identification method is proposed. Firstly, the coupled road excitation model of vehicle speed and speed bump is established, and then the 4-DOF vehicle model of half car is established. At the same time, considering that the double input vibration of the front and rear wheels will be coupled when vehicle passes through the speed bump, the model is decoupled. Then, the vertical trajectory of the body in the front axle position is obtained by Carsim software simulation.

Considering the change of vehicle future power demand in the process of energy distribution can improve the fuel saving effect of hybrid system. However, current studies are mostly based on historical information to predict the future power demand, where it is difficult to guarantee the accuracy of prediction. To tackle this problem, this paper combines hybrid energy management with predictive cruise control, proposing a hierarchical control strategy of predictive energy management (PEM) that includes two layers of algorithms for speed planning and energy distribution. In the interest of decreasing the energy consumed by power components and ensuring transportation timeliness, the upper-level introduces a predictive cruise control algorithm while considering vehicle weight and road slope, planning the future vehicle speed during long-distance driving.

As an off-road racing car, driving conditions for a Baja racing car are particularly complex. Extreme working conditions such as deep pits and rocky roads have put higher demand on structural strength and frame safety. To solve this problem, extreme working conditions are first studied to check the safety of the steel tube frame of Baja racing cars. Secondly, based on Noise, Vibration, and Harshness (NVH) to explore the frame's characteristics, analyze the frame's six-order mode, make the corresponding optimization, and solve the resonance problem caused by engine excitation and other factors. Finally, the natural frequency of the frame is measured to verify the effectiveness of the NVH characteristic optimization results, and it is found that the experimental results match the theoretical values. The theoretical analysis results are mainly based on ANSYS software's static and modal analysis.

In this paper, tensile experiments were performed on the dorsal and ventral skin of rats, and the mechanical properties of the skin in these two sites were compared and analyzed. A three-factor experimental protocol of site (dorsal and ventral), strain rate (0.71s-1, 7.1×10-3s-1), and sampling orientation (0°, 45° and 90° relative to the spine) was established for tensile test using the L6(31×22) orthogonal table modified from the standard orthogonal table L4 (23). Uniaxial tensile experiments were performed on rat skin samples to calculate the stress-strain curve. The failure strain energy was selected as the index, and the sum of squared deviations of the factors to the index was calculated by analysis of variance (ANOVA), and the contributions of the factors to the failure strain energy were evaluated. The results showed that the site factor has the largest effect on the tensile strain energy with a contribution of 88.9% and a confidence level of 95%.

For cooperative adaptive cruise control (CACC) system, a robust following control algorithm based on fuzzy PID principle is adopted in this paper. Firstly, a nonlinear vehicle dynamics model considering the lag of driving force and acceleration constraints was established. Then, with the vehicle’s control hierarchic, the upper controller takes the relative speed between vehicles and the spacing error as inputs to output the following vehicle's target acceleration, while the lower controller takes the target acceleration as inputs and the throttle opening and brake master cylinder pressure as outputs. For the setting of target spacing, this paper additionally considers the relative speed between vehicles and the acceleration of the front vehicle. Through testing, compared with the traditional variable safety distance model, the average distance reduces by 5.43% when leading vehicle is accelerating, while increases by 2.74% in deceleration.

It is generally considered that the material properties of foam are the most important factors in vehicle seat, which affect the human-seat interface pressure. Therefore, only the role of foam is usually considered when the finite element method is used to simulate the human-seat interface pressure. In this paper, the mechanical properties and the modeling method of commonly used seat cover material were studied. The models of the seat with and without cover were established respectively according to the real-vehicle seat geometric data, and the human-seat interface pressure was simulated after the seat and human model consisting of bones, soft tissue and skin were assembled. The simulation result was compared with the actual measurement results from test, which verified the accuracy of the simulation and the role of seat cover in the human-seat interface pressure simulation.

A flow channel design of the battery liquid cooling plate is carried out through the variable density topology optimization method according to the heat dissipation requirements of lithium-ion power batteries under actual working conditions. Firstly, given the non-uniform heat generation of lithium battery cells, the heat generation mechanism is studied so that the battery electro-thermal model is established, then the distribution regularity of heat generation rate in the cell at different discharge rates is obtained. Subsequently, through COMSOL Multiphysics simulation software, the multi-objective topology optimization of the primary configuration radiator is conducted. The weights of the optimization objectives minimum temperature and minimum flow resistance are determined by practical engineering application. Finally, an optimized model with a volume fraction of 50% was obtained.

The battery liquid cooling system can ensure that the battery works within a suitable temperature range, improve the safety performance of the battery system, and ensure the cruising range. This paper introduces a design scheme of a stamped double-parallel liquid cooling plate. Based on the STAR-CCM+ simulation software, a thermal simulation model of the battery management system is established to analyze the thermal behavior of the battery system and to study the effect of the inlet mass flow rate on the temperature of the top surface of the batteries. At the same time, with the analysis of the proportion of pressure drop of each component in the liquid cooling plate, an optimization of inserted part in the liquid cooling plate is proposed. The numerical analysis results are compared with the experimental results of the pressure drop to improve the effectiveness of the optimization scheme.

The powers generated by the skidding and slipping of a vehicle in unit time during driving are referred to as parasitic power. It has significant effects on wear on the tires, service life, and overall efficiency. However, existing methods to calculate parasitic power expressions that are not solvable in some cases, the reasonableness of the results of their calculations cannot be verified by experiments and the parameters of the loader cannot be calculated during the design of the vehicle. In this paper, we systematically analyze the mechanism of generation of parasitic power based on the differences in the radii of the tires of loaders. We innovatively propose a theoretical calculation method to calculate the wheel circumference parasitic work during the design of the loader. The results of experiments show that errors between the theoretical and experimental values of the wheel circumference parasitic work calculated under various working conditions were smaller than 5%.

In this paper, a high-efficiency and low-cost lithium-ion battery pack active balance system is designed. It adopts a distributed structure and consists of three parts: auxiliary power module, one-way isolated DC/DC conversion module, and a battery group. The battery single cells in the battery pack are layered and divided into m battery groups in total, and each battery group is composed of n battery single cells. Each battery group is connected to an isolated DC/DC conversion module, and all the conversion modules are connected in parallel with the auxiliary power. Taking the SOC average value of the all-single cells in one battery group as the balancing variable, the auxiliary power is controlled to charge the battery group with the lower SOC average value, so that the difference of the SOC average value of all battery groups is within the set threshold range, so as to realize the active balance of each battery group.

Overloading of trucks can easily cause damage to roads, bridges and other transportation facilities, and accelerate the fatigue loss of the vehicles themselves, and accidents are prone to occur under overload conditions. In recent years, various countries have formulated a series of management methods and governance measures for truck overloading. However, the detection method for overload behavior is not efficient and accurate enough. At present, the method of dynamic load identification is not perfect. No matter whether it is the dynamic weight measurement method of reconstructing the road surface or the non-contact dynamic weight measurement method, little attention is paid to the difference of different vehicles. Especially for different vehicles, there should be different load limits, and the current devices are not smart enough.

In the process of truck overload and over-limit detection, it is necessary to detect the characteristics of the vehicle's size, type, and wheel number. In addition, in some vehicle vision-based load recognition systems, the vehicle load can be calculated by detecting the vibration frequency of specific parts of the vehicle or the change in the length of the suspension during the vehicle's forward process. Therefore, it is essential to quickly and accurately identify vehicle features through the camera. This paper proposes a vehicle feature recognition method based on image semantic segmentation and Python, which can identify the length, height, number of wheels and vibration frequency at specific parts of the vehicle based on the vehicle driving video captured by the roadside camera.