Search Results

Injector nozzle deposits can have a profound effect on particulate emissions from vehicles fitted with Gasoline Direct Injection (GDI) engines. Several recent publications acknowledge the benefits of using Deposit Control Additives (DCA) to maintain or restore injector cleanliness and in turn minimise particulates, but others claim that high levels of DCA could have detrimental effects due to the direct contribution of DCA to particulates, that outweigh the benefits of injector cleanliness. Much of the aforementioned work was conducted in laboratory scenarios with model fuels. In this investigation a fleet of 7 used GDI vehicles were taken from the field to determine the net impact of DCAs on particulates in real-world scenarios. The vehicles tested comprised a range of vehicles from different manufacturers that were certified to Euro 5 and Euro 6 emissions standards.

Design efforts to improve the hydraulic efficiency of high-pressure diesel fuel systems and thus further improve overall engine efficiency have resulted in the utilisation of low-spill control valves and reduced injector component clearances to reduce general leakage losses. Overall, these advances have contributed significantly to the high efficiency diesel engines of today. However, the combination of very high fuel pressures, cavitation and low fuel leakage volumes increases the heating of the remaining fuel, increasing temperature and, in turn, the propensity for deposits to form inside the injector. This deposit phenomenon is commonly known as Internal Diesel Injector Deposits (IDID) and can cause rough engine running and failed engine starts requiring injector cleaning or replacement. Methods studying this phenomenon are under development in the industry.

In the present study, Large Eddy Simulations (LES) have been performed with a 3D model of a step nozzle injector, using n-pentane as the injected fluid, a representative of the high-volatility components in gasoline. The influence of fuel temperature and injection pressure were investigated in conditions that shed light on engine cold-start, a phenomenon prevalent in a number of combustion applications, albeit not extensively studied. The test cases provide an impression of the in-nozzle phase change and the near-nozzle spray structure across different cavitation regimes. Results for the 20oC fuel temperature case (supercavitating regime) depict the formation of a continuous cavitation region that extends to the nozzle outlet. Collapse-induced pressure wave dynamics near the outlet cause a transient entrainment of air from the discharge chamber towards the nozzle.

Improved fuel economy is increasingly a key measure of performance in the automotive industry driven by market demands and tighter emissions regulations. Within this environment, one way to improve fuel economy is via fuel additives that deliver friction- reducing components to the piston-cylinder wall interface. Whilst the use of friction modifiers (FMs) in fuel or lubricant additives to achieve fuel economy improvements is not new, demonstrating the efficacy of these FMs in vehicles is challenging and requires statistical design together with carefully controlled test conditions. This paper describes a bespoke, efficient, high-precision vehicle testing procedure designed to evaluate the fuel economy credentials of fuel-borne FMs. By their nature, FMs persist on engine surfaces and so their effects are not immediately reversible upon changing to a non FM-containing fuel (“carryover” effect), therefore requiring careful design of the test programme.

In Europe, the development and implementation of new regulatory test procedures including the chassis dynamometer (CD) based World Harmonised Light Duty Test Procedure (WLTP) and the Real Driving Emissions (RDE) procedure, has been driven by the close scrutiny that real driving emissions and fuel consumption from passenger cars have come under in recent times. This is due to a divergence between stated certification performance and measured on-road performance, and has been most pointed in the case of NOx (oxides of nitrogen) emissions from diesel cars. The RDE test is certainly more relevant than CD test cycles, but currently certification RDE cycles will not necessarily include the most extreme low speed congested or low temperature conditions which are likely to be more challenging for NOx after-treatment systems.

The accepted model of conventional diesel combustion [1] assumes a rich premixed flame slightly downstream of the maximum liquid penetration. The soot generated by this rich premixed flame is burnt out by a subsequent diffusion flame at the head of the jet. Even in situations in which the centre of combustion (CA50) is phased optimally to maximize efficiency, slow late stage combustion can still have a significant detrimental impact on thermal efficiency. Data is presented on potential late-stage combustion improvers in a EURO VI compliant HD engine at a range of speed and load points. The operating conditions (e.g. injection timings, EGR levels) were based on a EURO VI calibration which targets 3 g/kWh of engine-out NOx. Rates of heat release were determined from the pressure sensor data. To investigate late stage combustion, focus was made on the position in the cycle at which 90% of the fuel had combusted (CA90). An EN590 compliant fuel was tested.

Demonstrating the cost/benefits of technologies in the automotive sector is becoming very challenging because the benefits from technologies are sometimes of similar magnitude to testing precision. This paper aims to understand vehicle-borne imprecision and the effect of this on the quality of chassis dynamometer (CD) testing. Fuel consumption and NOx emissions precision is analyzed for two diesel vehicles with particulate filter and SCR systems. The two vehicles were tested on a high precision CD facility over the NEDC (New European Drive Cycle) and WLTC (World harmonized Light-duty Test Cycle) cycles. The CD base precision of testing was characterized between 0.6-3% depending on the cycle phase. A novel application of multi-variate statistical analysis was used to identify the factors that affected testing precision, allowing isolation of small differences that were not obvious when conducting cycle-averaged or cycle-phase-averaged analysis.

Low Temperature Combustion using compression ignition may provide high efficiency combined with low emissions of oxides of nitrogen and soot. This process is facilitated by fuels with lower cetane number than standard diesel fuel. Mixtures of gasoline and diesel (“dieseline”) may be one way of achieving this, but a practical concern is the flammability of the headspace vapours in the vehicle fuel tank. Gasoline is much more volatile than diesel so, at most ambient temperatures, the headspace vapours in the tank are too rich to burn. A gasoline/diesel mixture in a fuel tank therefore can result in a flammable headspace, particularly at cold ambient temperatures. A mathematical model is presented that predicts the flammability of the headspace vapours in a tank containing mixtures of gasoline and diesel fuel. Fourteen hydrocarbons and ethanol represent the volatile components. Heavier components are treated as non-volatile diluents in the liquid phase.

Precise, repeatable and representative testing is a key tool for developing and demonstrating automotive fuel and lubricant products. This paper reports on the first findings of a project that aims to determine the requirements for highly repeatable test methods to measure very small differences in fuel economy and powertrain performance. This will be underpinned by identifying and quantifying the variations inherent to this specific test vehicle, both on-road and on Chassis Dynamometer (CD), that create a barrier to improved testing methods. In this initial work, a comparison was made between on-road driving, the New European Drive Cycle (NEDC) and World harmonized Light-duty Test Cycle (WLTC) cycles to understand the behavior of various vehicle systems along with the discrepancies that can arise owing to the particular conditions of the standard test cycles.

Carbonaceous deposits can accumulate on various surfaces of the internal combustion engine and affect its performance. The porous nature of these deposits means that they act like a “sponge”, adsorbing fuel components and changing both the composition and the amount of fuel in the combustion chamber. Here we use a previously developed and validated model of engine deposits to predict adsorption of normal heptane, isooctane, toluene and their mixtures in deposits of different origin within a port fuel injected spark ignition engine (Combustion Chamber Deposits, or CCDs, and Intake Valve Deposits, or IVDs) and under different conditions. We explore the influence of molecular structure of adsorbing species, composition of the bulk mixture and temperature on the uptake and selectivity behaviour of the deposits. While deposits generally show high capacity toward all three components, we observe that selectivity behaviour is a more subtle and complex property.

The paper discusses the concept, design and final results from the ‘Ultra Boost for Economy’ collaborative project, which was part-funded by the Technology Strategy Board, the UK's innovation agency. The project comprised industry- and academia-wide expertise to demonstrate that it is possible to reduce engine capacity by 60% and still achieve the torque curve of a modern, large-capacity naturally-aspirated engine, while encompassing the attributes necessary to employ such a concept in premium vehicles. In addition to achieving the torque curve of the Jaguar Land Rover naturally-aspirated 5.0 litre V8 engine (which included generating 25 bar BMEP at 1000 rpm), the main project target was to show that such a downsized engine could, in itself, provide a major proportion of a route towards a 35% reduction in vehicle tailpipe CO2 on the New European Drive Cycle, together with some vehicle-based modifications and the assumption of stop-start technology being used instead of hybridization.

Deposits forming in the injector nozzle holes of modern diesel cars can reduce and disrupt the fuel injected into the combustion chamber, causing reduced or less efficient combustion, resulting in power loss and increased fuel consumption. A study of the factors affecting injector nozzle tip temperature, a parameter critical to nozzle deposit formation, has been conducted in a Peugeot DW10 passenger car bench engine, as used in the industry standard CEC F-098 injector nozzle deposit test, [1]. The findings of the bench engine study were applied in the development of a Chassis Dynamometer (CD) based vehicle test method using Euro 5 compliant vehicles. The developed test method was refined to tune the conditions as far as practicable towards a realistic driving pattern whilst maintaining sufficient deposit forming tendency to enable test duration to be limited to a reasonable period.

A predictive model for estimating the fuel saving of “top tier” engine, axle and transmission lubricants (compared to “mainstream” lubricants), in a heavy duty truck, operating on a realistic driving cycle, is described. Simulations have been performed for different truck weights (10, 20 and 40 tonnes) and it was found that the model predicts percentage fuel economy benefits that are of a similar magnitude to those measured in well controlled field trials1. The model predicts the percentage fuel saving from the engine oil should decrease as the vehicle load increases (which is in agreement with field trial results). The percentage fuel saving from the axle and gearbox oils initially decreases with load and then stays more or less constant. This behaviour is due to the detailed way in which axle and gearbox efficiency varies with speed/load and lubricant type.

GTL (Gas-To-Liquid) fuel is well known to improve tailpipe emissions when fuelling a conventional diesel vehicle, that is, one optimized to conventional fuel. This investigation assesses the additional potential for GTL fuel in a GTL-dedicated vehicle. This potential for GTL fuel was quantified in an EU 4 6-cylinder serial production engine. In the first stage, a comparison of engine performance was made of GTL fuel against conventional diesel, using identical engine calibrations. Next, adaptations enabled the full potential of GTL fuel within a dedicated calibration to be assessed. For this stage, two optimization goals were investigated: - Minimization of NOx emissions and - Minimization of fuel consumption. For each optimization the boundary condition was that emissions should be within the EU5 level. An additional constraint on the latter strategy required noise levels to remain within the baseline reference.

Building on two decades of expertise, a fourth generation fleet test protocol is presented for assessing the response of engine performance to gasoline additive treatment. In this case, the ability of additives to remove pre-existing deposit from the intake systems of port fuel injected vehicles has been examined. The protocol is capable of identifying real benefits under realistic market conditions, isolating fuel performance from other effects thereby allowing a direct comparison between different fuels. It is cost efficient and robust to unplanned incidents. The new protocol has been applied to the development of a candidate fuel additive package for the North American market. A vehicle fleet of 5 quadruplets (5 sets of 4 matched vehicles, each set of a different model) was tested twice, assessing the intake valve clean-up performance of 3 test fuels relative to a control fuel.

Addition of nitroalkanes to gasoline is shown to reduce the octane quality. The reduction in the Motor Octane Number (MON) is greater than the reduction in the Research Octane Number (RON). In other words addition of nitroalkanes causes an increase in octane sensitivity. The temperature of the compressed air/fuel mixture in the MON test is higher then in the RON test. Through chemical kinetic modelling, we are able to show how the temperature dependence of the reactions responsible for break-up of the nitroalkane molecule can lead to an increase in octane sensitivity. Results are presented from an Homogenous Charge Compression Ignition (HCCI) engine with a homogeneous charge in which the air intake temperature was varied. When the engine was operated on gasoline-like fuels containing nitroalkanes, it was observed that the combustion phasing was much more sensitive to the air intake temperature. This suggests a possible means of controlling combustion phasing for HCCI.

The Coordinating European Council, CEC, develops performance tests for the motor, oil, petroleum, additive and allied industries. In recent years, CEC has moved away from using round robin programmes (RRP's) for monitoring the precision and severity of test methods in favour of regular referencing within a test monitoring system (TMS). In a TMS, a reference sample of known performance, determined by cross-laboratory testing, is tested at regular intervals at each laboratory. The results are plotted on control charts and determine whether the installation is and continues to be fit to evaluate products. Results from all laboratories are collated and combined to monitor the general health of the test. The TMS approach offers considerable benefits in terms of detecting test problems and improving test quality. However, the effort required in collating data for statistical analysis is much greater, and there are technical difficulties in determining precision from TMS data.

Because reformer technology can be used in conjunction with advanced internal combustion engine technology, it is important to be able to formulate fuels that are compatible with both reformers and ICEs It has been found that most hydrocarbon species typically present in gasoline can be reformed with relative ease. The exception is that olefinic species of carbon number 6 and above are relatively much harder to reform. It is shown how a reformer compatible gasoline fuel with high octane can be blended. For Diesel fuels, synthetic ‘Gas to Liquid’ fuels are generally less susceptible to coking and hence superior to petroleum-derived fuels, for use with an onboard reformer.

A road test has been conducted to quantify the benefits provided by a high-performance gasoline additive package in a fleet of cars representative of Europe, SE Asia, and South America. The emissions, fuel consumption, and engine cleanliness benefits of additised versus untreated gasoline were compared in 15 pairs of cars. A further 6 cars were operated on a mixture of fuels to show the benefits of additised fuel versus mixed fuelling. The design of the experiment was based on a similar road test conducted in 1991. Through careful test design and execution, it has been possible to assess the performance of the package at a high statistical confidence level. The package provides a high level of inlet system cleanliness, a significant reduction in fuel consumption and reduced HC emissions.

We review some of the key tribological issues of relevance to motorsport applications. Tribology is the science of friction and wear, and in a high performance engine, friction and wear are controlled by good component design (e.g. the engine and the transmission) and also by the use of high performance lubricants with the correct physical (and chemical) properties, matched to the machine they are used in. In other words, design of a specific lubricant for specific hardware can lead to optimised performance. (Tribology is also important in the tire-road contact but are not considered here.) The importance of key physical properties of a lubricant is demonstrated with an emphasis on how the choice of the correct lubricant can help to minimize engine friction (and thus increase available power output) whilst protecting against engine wear. Key lubricant parameters discussed in the paper are the viscosity variation of a lubricant with temperature, shear rate and pressure.