Search Results

This project was undertaken with an objective to develop methodology by formulating set of procedures that would help in achieving the end goal. Once methodology is established, it paves way to optimize the end results more effectively which results in reduced lead time during product development. Methodology can either be based on pure experimental investigations or by simulations. Combination of mathematical and empirical approach is inherently followed in simulations, which helps in reducing the testing time and overall cost. Commercial vehicles (CV) have seen paradigm shift in the fuel consumption (FC) certification approaches, with an intention to align with 2016 Paris climate agreement. Use of simulation tool like VECTO for commercial vehicle FC certification has gained momentum in Europe. Overall experience gained in commercial vehicle FC simulation has motivated us to leverage the learnings for off-road applications like agricultural tractors.

Closed crankcase ventilation prevent harmful gases from entering atmosphere thereby reducing hydrocarbon emissions. Ventilation system usually carries blowby gases along with oil mist generated from Engine to Air intake system. Major sources of blowby occurs from leak in combustion chamber through piston rings, leakage from turbocharger shafts & leakage from valve guides. Oil mist carried by these blowby gases gets separated using separation media before passing to Air Intake. Fleece separation media has high separation efficiency with lower pressure loss for oil aerosol particles having size above 10 microns. However, efficiency of fleece media drops drastically if size of aerosol particles are below 10 microns. Aerosol mist of lower particle size (>10 microns) generally forms due to flash boiling on piston under crown area and from shafts of turbo charger due to high speeds combined with elevated temperatures. High power density diesel engine is taken for our study.

Construction equipment off highway vehicles are heavy industry vehicles that run on diesel engines. To meet the emission norms, these engines have the Exhaust After Treatment System (EATS) which includes two primary subassemblies, i.e., a Diesel Oxidation Catalyst (DOC) subassembly to reduce the HC and CO emissions and a Selective catalytic Reduction (SCR) subassembly to reduce NOx emissions. Because of the excessive vibrations in the engine and continuous heavy-duty usage of the Construction equipment, any failures in the EATS system leading to escape of exhaust gas is a statuary non-compliance. Hence, understanding the effect of engine vibrations and proposing a cost-effective solution is paramount in designing the EATS system including the SCR assembly. A field-testing failure of an SCR assembly has been taken in consideration for this study.

Ethanol-gasoline blended fuels have been widely implemented in Indian markets followed by the Govt of India’s road map as ethanol reduces life-cycle greenhouse gas emissions and improves anti-knock performance. However, effects of Ethanol Blending on engine out emissions characteristics including particulates from gasoline direct injection (GDI) engine remains under development and investigation. In this study the effect of ethanol blended gasoline fuels with two blending rates 10% and 20% (v/v %) on catalyst conversion efficiencies and emissions on a 1.2 litre 3-cylinder turbo GDI engine is investigated. The addition of ethanol to gasoline fuel enhances the Octane rating (RON) of the blended fuels, oxygen content and changes Reid vapor pressure (RVP). The influence of lambda biasing, and lambda trim controller has been tested. The approach for calibration was adopted based on achieving the target pollutant conversion efficiencies.

BS6.1 emission standards were implemented in India in 2020 followed by BS6.2 which added more controls on emission limits. For BS6.2 OBD (On Board Diagnostics) and RDE (Real Driving Emission) were added on to the existing BS6.1 emissions. Emission control changes usually need addition of new parts, calibration changes and durability requirements. For the current 1.5L, 3-cylinder diesel engine an pSCR (Passive Selective Catalytic Reduction) brick was added for control of NOx for meeting RDE. For meeting OBD requirements PM (Particulate Matter) and NOx sensors were added in the cold end pipe along with calibration changes to meet the BS6.2 norms. In this paper we will discuss on the design aspects of sensors and pSCR only. The sensor and pSCR positioning plays vital role in meeting the legislative requirements and to ensure the ease of assembly and durability of the parts.

In automotive market, with competitive car prices, build quality of a car will be a major distinguishing factor. Consumer's need for acoustic comfort has evolved from the removal of annoying noises to perceived sound quality. Operational sounds from electromechanical systems like sunroof system, window regulator, door lock system, HVAC etc. directly interact with users’ senses. The perceived acoustics comfort of these sounds are direct indicators of vehicle character and can influence customer’s buying decision. With the reduction in product development time and stringent cost constraints, a proper structured target setting methodology to benchmark & evaluate these operational sounds is crucial. In this paper, such a target setting methodology is proposed and discussed for operational sound quality evaluation. Electromechanical noises from various vehicles are measured using binaural head measurement system.

The purpose of this study is to conduct dynamic seat pressure mapping on vehicle seats during its operation on different test tracks under ambient environmental conditions for a defined speed. The test track comprises of pave roads, high frequency track, low frequency track and twist track. The variations in pressure distribution on seat during diverse road load inputs help to understand the seat cushion and back comfort for unique percentiles of human subjects ranging from 50th to 95th percentile population. For conducting the study, a sport utility vehicle (SUV) loaded with leatherette seats has chosen. Totally six participants (human subjects), five male and one female selected for the study based on their BMI (Body mass index) and body morphology. Pressure mats suitable for taking dynamic load inputs and able to log the data at a defined sampling rate mounted on seats and secured properly. The pressure mats should cover the seat cushion, bolster areas and back seat completely.

The implementation of TREM/CEV 5 emission norms on farm equipment will bring in cost pressure due to the need for exhaust after treatment systems. This cost increase needs to be reduced by bringing in more efficient and effective processes to shorten the development phase and to provide better fuel efficiencies. In this work ETAS ASCMO Online DoE with Constraint Modelling (ODCM) was applied to execute smart online DoE on a new common rail diesel engine with EGR, whose exact bounds of operation was not available. A Global test plan with ASCMO Static was created without much focus on detailed constraints of engine operation, other than the full load curve. The parameters which were selected were Speed, Torque, Rail Pressure, Main Timing, EGR Valve Position, Pilot Separation and Quantity and Post Quantity and Separation. For these parameters, the safe operating bounds were not available. This ASCMO Static test plan is automated and executed on engine test cell with ETAS INCAFlow.

Commercial transportation is the key pillar of any growing economy. Light and Small commercial vehicles are increasing every day to cater the logistics demand, but there is always a gap between customer’s actual and desired operational efficiency. This is because of lack of organized fleet and efficient fleet operation. The major requirement of fleet owners is timely delivery, high productivity, downtime reduction, real time tracking, etc., Automakers are now providing fleet management application in modern LCV & SCV to satisfy the fleet operator requirement. However, any feature malfunction, consignment mismatch, wrong notification, missed alerts, etc., can incur huge loss to fleet operator and disrupt the entire supply chain. Hence it is very critical to extensively validate the telematics features in fleet management application. This paper explains the approach for exhaustive validation strategy of fleet management applications (B2B) from end user perspective.

Effective 1st April 2023, India's automotive emissions regulation has shifted from BS-VI Stage-1 to BS-VI Stage-2 standard the after-treatment systems need to demonstrate robust performance not just on the cycle, but also to demonstrate emissions for on-road Real Driving Emission (RDE) conditions. A stringent On-Board Diagnostics (OBD) strategy to monitor the real-time emission levels along with compliance Road Driving Emissions (RDEs) are focus areas for BS VI Stage-2 emission legislation. The maximum speed on MIDC is 90km/h in BS-VI Stage-1, Diesel Oxidation Catalyst (DOC)+Selective Catalyst Reduction Filter (SCRF®) was able to meet legislation at the lab, and now with the RDE cycle max speed of the vehicles under the M1 category <3.5 T will have the max permitted legal limit shall surpass 100 km/h for not around 3% of the span in the third phase of driving cycle for which max speed is up to 120 km/h.

In developing countries, the commercial vehicle industry is one of the key drivers for economic growth. The commercial vehicle industry in India is expected to reach 11,80,000 units by 2025 with a CAGR of 18% from CY 2020 to CY 2025 [1]. In the price sensitive segment of small commercial vehicles, it is imperative to incorporate accurate fuel economy measurement techniques during product development stage to deliver maximum value to the customer. In this approach, measuring the fuel consumption of small commercial vehicles in real world driving conditions in real time is one of the most critical aspects in engine calibration development and fine tuning. One of the challenges in measuring fuel consumption in sub 1 liter diesel engines is the very low fuel flow rate in the fuel feed line which keeps varying as per the driver demand.

This paper takes a review of fretting phenomenon on splines of the engaging gears and corresponding splines on shaft of automotive transmission and how it leads to failure of other components in the gearbox. Fretting is a special wear process which occurs at the contact area of two mating metal surfaces when subject to minute relative oscillating motion under vibration. In automotive gearbox, which is subjected to torsional vibrations of the powertrain, the splines of engaging gears and corresponding shaft may experience fretting, especially when the subject gear pair is not engaged. The wear debris formed under fretting process when oxidizes becomes very hard and more abrasive than base metal. These oxidized wear particles when comes in mesh contact with nearby components like bearings, gears etc. may damage these parts during operation and eventually lead to failure.

Precise control over mixture formation withhigh fuel pressure and multiple injections allows Gasoline Direct Injection (GDI) engines to be operated satisfactorily at extreme conditions wherePort Fuel Injection (PFI) engines wouldnormally struggle due to combustion instability issues. Catalyst heating phase is one such important condition which is initiated after a cold engine start to improve the effectiveness of the three-way catalyst (TWC). For a given TWC specification, fast light-offof TWC is achieved in the catalyst heating phase by increasing the exhaust gas temperature with higher exhaust mass flow. The duration of this phase must be as short as possible, as it is a trade-off between achieving sufficient TWC light off performance and fuel efficiency.

Automotive manufacturers are constantly working towards enhancing the driving experience of the customers. In this context, improving the static and dynamic gear shift quality plays a major role in ensuring a pleasant and comfortable driving experience. Moreover, the gear shift quality of any manual transmission is mainly defined by the design of the synchronizer system. The synchronizer sleeve strut detent groove profile plays a vital role in defining the performance of the synchronizer system by generating the minimum required pre-synchronization force. This force is important to move the outer synchronizer ring (blocker ring) to the required index position and to wipe-out the oil from the conical friction surfaces to build rapid high cone torque. Both these functional requirements are extremely critical to have a smooth and quick synchronization of the rotating parts under dynamic shift conditions.

Synchronizers are the most critical parts of a manual transmission. There are classical calculations available for the synchronizer design and studies are available for the normal functioning of synchronizer rings which describes how the synchronizer behaves in the event of gear shifting. The objective of this study is to describe the synchronizer behavior when synchronizers are not functional, i.e., in other gear engaged condition and the rings are free. This study describes the failure mechanism of the unused synchronizer rings which are moving freely in the packaging space. The findings of this synchronizer design cannot be limited only for synchronizer performance and standard durability calculations. To ensure proper function of synchronizer rings and to achieve the required life the external parameters like clearances, lubrication, clutch design for dampening torsional vibration from the engine are to be considered.

Automotive manufacturers are concerned about the safety of its customers. Safety critical components like wheel hub are designed considering the severe loads generated from various customer usage patterns. Accelerated tests, which are derived from Real World Usage Patterns (RWUP), are conducted at vehicle level to ensure the wheel hub meet the durability targets. Load and strain measurement are done to understand the critical lateral loading undergone by the wheel hub. Measured data is synthesized to drive the duty cycle. Finite Element (FE) Analysis of Wheel end is performed at module level considering measured loads to capture the exact load path in physical test. Simulation results are compared with the measured strain for validating the FE analysis procedure. FE analysis was repeated for different wheel hub designs, combinations of different flange radius (R) and flange width (t), to understand the effect of the two critical dimensions on wheel hub durability.

Use of Computer Aided Engineering (CAE) tools for virtual validation has become an essential part of every product development process. Using CAE tools, accurate prediction of potential failure locations is possible even before building the proto. This paper presents a detailed case study of virtual validation of Backhoe Loader (BHL) dipper arm using CAE tools (MBD: Multi Body Dynamics and FEA: Finite Element Analysis) and comparison of simulation results with test data. In this paper, we have illustrated the modelling of Backhoe Loader in MSc ADAMS software. The detail ADAMS model was created and validated. The component mass, Center of Gravity (C.G) and Mass Moment of Inertia (MOI) was taken from CAD data. Trenching is simulated by operating the different hydraulic cylinders of the BHL. Loader arm cylinders and stabilizer cylinders are operated to lift the machine tires above the ground level.

For Automatic transmission application, crankshaft torque is transferred to torque converter through flex plate. As the flex plate has no functional requirement of storing energy as in case of Manual Transmission (MT) flywheel, flex plate design can be optimized to great extent. Flex plate structure must have compliance to allow the axial deformation of torque convertor due to ballooning pressure generated inside the converter. Flex plate experiences dynamic torque and centrifugal forces due to high rotational speed. It should have compliance to accommodate the assembly misalignments with torque convertor in both axial and radial directions. In this paper, sequential and hybrid optimization techniques are described to optimize the flex plate design with stress, stiffness and mass as design constraints. The load path, corrugation length and axial stiffness of flex plate captured accurately using this hybrid optimization.

Ride is essentially the outcome of coupled dynamics of various involved sub-systems which make it too complex to deal analytically. Tires, amongst these, are known to be highly nonlinear compliant systems. Selection of tires specifications such as rated tyre pressure, etc. are generally decided through subjective assessment. While experts agree that tyre pressure affects the attributes such as ride to a noticeable degree, the quantification of the change often remains missing. In the current work, vibration levels of various sub-systems relevant to ride in an SUV are measured for three different tyre pressures at different speeds over the three randomly generated roads. For the purpose, artificial road profiles of classes A, B and C are synthesized from the spectrum of road classes defined in ISO 8608:2016 and reproduced on a four-poster test rig.

This study presents a method for a cool down simulation of passenger compartments. The purpose was to integrate the 3D Computational Fluid Dynamics (CFD) software StarCCM+ with the 1D thermal management software KULI. The targets were to achieve accurate prediction of temperature diffusion inside the cabin for a transient cycle simultaneously reducing the modelling effort and CPU-time consumption. The 1D simulation model was developed in KULI and the flow field data required to simulate mass flow and diffusion inside the cabin was implemented from Star CCM+. The simulation model consists of a multi-zone cabin and models the complete refrigerant circuit consisting of evaporator, condenser, Thermal Expansion Valve (TXV) and compressor. This paper describes the process flow, definition of the inputs required and finally the validation of the simulation data with experiments.