Search Results

Increasing combustion pressure, low viscosity oils, less oil supply and the increasing stress due to downsizing of internal combustion engines (ICE) lead to higher loads within the bearing. As the mechanical and tribological loads on the piston pin bearings have a direct impact on the service life and function of the overall engine system, it is necessary to develop a robust tribological design approach. Regarding the piston pin bearing of a diesel engine, this study aims to describe the effects of different parameters on a DLC-coated piston pin within the bearing. Therefore, an external engine part test rig, which applies various forces to the connecting rod and measures the torque on a driven pin, is used to carry out validation measurements. The special feature of the test bench is the way the piston is beared. For the first experiments, the piston crown is placed against a plate (plate-bearing); later, this plate-bearing is replaced by a hydrostatic bearing.

Pilot injection gas engines are commonly used as large stationary engines. Often, the combustion is implemented as a dual-fuel strategy, which allows both mixed and diesel-only operation, based on a diesel engine architecture. The current research project focuses on the application of pilot injection in an engine based on gasoline components of the passenger car segment, which are more cost-effective than diesel components. The investigated strategy does not aim for a diesel-only combustion, hence only small liquid quantities are used for the main purpose of providing a strong, reliable ignition source for the natural gas charge. This approach is mainly driven to provide a reliable alternative to the high spark ignition energies required for high cylinder charge densities. When using such small liquid quantities, a standard common-rail diesel nozzle will apparently not be ideal regarding some general specifications.

In January 1996 Mercedes-Benz has introduced a new 4-cylinder engine OM 904 LA of the new engine family for light commercial vehicles. The power range of the OM 904 LA comprises ratings from 90 kW up to 125 kW at 2300 rpm. From the beginning of the design of this engine, a noise emission output as low as possible was strived for, aside from the high targets as far as durability, maintenace and fuel consumption are concerned. The basis is the development of noise regulations for commercial vehicles. The noise reduction measures have to be concentrated on the engine since up to now it still is one of the main noise emission sources at the vehicle. Already at the lay-out of the engine the prerequisits for a low-noise engine behaviour have been taken into consideration. The engine is equipped with a fuel injection system featuring particular unit injector pumps for each cylinder which is superior to the conventional in-line injection pump as far as acoustics are concerned.

The demand for fuel-efficient, low-displacement engines for future passenger car applications led to investigations with small DI diesel engines in the advanced engineering department at Mercedes-Benz. Single-cylinder tests were carried out to compare a 2-valve concept with 241 cm3 displacement with a 422 cm3 4-valve design, both operated with a common rail injection system. Mean effective pressures at full load were about 10 % lower with the smaller displacement. With such engines a specific power of 40 kW/I and a specific torque of about 140 Nm/I should be possible. In the current stage of optimization, penalties in fuel economy could be reduced down to values below 3 %. The “4-cylinder DI diesel engine with 1 liter displacement” is an interesting alternative to small 3 cylinder concepts with higher displacement per cylinder. An introduction into series production will not only depend on the potential for further improvement in fuel economy of such small cylinder units.

The comparison of a light weight crankcase to the production cast iron crankcase of the new Mercedes Benz 2.9-liter direct injection (DI) five-cylinder turbo diesel engine with intercooler is described. The light weight crankcase is cast from the aluminum alloy A 356 while other engine components like oil pan, timing case cover and brackets are manufactured from a magnesium alloy. This paper describes the engine design with the simultaneous calculation, the mechanical development and the acoustic measurements. In this study an engine weight reduction of about 30 kg with comparable noise emission compared to the production engine with cast iron crankcase is realized.

Rear axle steering systems electronically controlled and hydraulically actuated are discussed for commercial vehicles. With these steered axles, the major objective is to improve the manoeuvrability of these vehicles. With the aid of the steering strategy “Rear end Swing-out Compensation” it will be assured, that in two-axle, all-wheel steering trucks dangerous rear end swing-out effects, occuring primarily in low speed ranges, will not take place. In addition, it is possible to enhance the dynamic stability of two-axle trucks while braking on split adhesion road surfaces with the aid of specific control algorithms. Furthermore, the application of a rear axle steering system can suppress dangerous lateral oscillations of centre-axle trailers.

As part of a comprehensive strategic product initiative the most important commercial vehicle manufacturer - Mercedes-Benz AG - is step by step renewing its entire product range. This primarily refers to the heart of the vehicles - the engine. After the OM 457 LA, which was developed together with DDC for the special American market demands and which is produced and sold in the U.S.A. by DDC under the label “Series 55”, has had its premiere in Freightliner's Century Class, the OM 904 LA will now follow in the light commercial vehicle class. This engine has a completely new concept of a direct-injection, highly sophisticated turbocharged four-cylinder in-line engine with air-to-air intercooler, whose main characteristics can be outlined by the terms “multi-valve technology”, high-pressure injection via unit pumps” and “electronic engine control”. This “small” engine has several interesting features, which - up to now - were only known from class 8 engines.

The problem of effectively reducing water spray formed by motor vehicles on wet roads remained up to now unsolved.Although numerous experimental investigations have been published, and comprehensive patent literature is available, the suggested solutions appear to be problematic under real-life conditions. In this paper, a configuration applicable both to commercial vehicles and passenger cars is proposed, which is restricted exclusively to the wings, and - with today's design principles - does not require any special advance preparation. A grooved channel profile in the wing causes the water spray to be reduced considerably without affecting the vehicle's suitability for everday use. An optoelectronic measuring instrument which is carried along the vehicle, makes it possible to conduct integral water spray measurements over time periods of various length.

Modern commercial vehicle engines are equipped with turbocharging and intercooling. This results in low emissions and fuel consumption. In the lower speed and load range and under transient conditions, these engines have disadvantages, as the fuel injection rate has to be limited to avoid excessive smoke emission. Also, the engine braking performance of highly charged, small displacement engines is also lower than that of large displacement engines. Mercedes-Benz decided to develop a combination of turbocharger and mechanical supercharger. In the lower speed range higher torque levels are possible and maximum torque is available without any lag especially in the transient mode with low smoke emission and fuel consumption. Vehicle performance during acceleration can be improved by up to 30%. During engine braking operation, the mechanical supercharger is activated throughout the whole engine speed range which results in a distinctive increase in braking power.

The simulation of the driving performance of motor vehicles offers the possibility of analyzing the behavior of new commercial vehicles or new systems to be integrated into the vehicle, already before the stage of the first prototypes. Thus, simulation technology may contribute to shorten the time and costs needed for the development of new vehicles and new vehicle systems. As an example, this contribution describes the simulation of a commercial vehicle with adaptive suspension elements. The simulations were used to coarse-tune the suspension elements before installation and fine-tuning them in a prototype vehicle, and to define and optimize the control strategies of electronically controlled suspension systems. A comparison between the costs of the simulation and estimated costs of corresponding field tests substantiates the economical benefits of the simulation.

The California Air Resources Board (CARB) has proposed procedures for the analysis of non-methane organic gases (NMOG) to determine the ozone forming potential (OFP) of automotive exhaust. For realization of these methods two differently configured GC systems are necessary. In order to reduce the efforts concerning costs, maintenance and quality control of two analytical instruments, a single run method is developed for routine analysis. This method allows identification and quantification of individual hydrocarbons (IHC) in the range of carbon numbers C2 to C12. Analytical problems arising from high contents of water and carbon dioxide in exhaust samples are discussed. Water reduction is obtained by a Nafion® Dryer by means of membrane diffusion of polar compounds. Contamination as well as memory effects due to this sample work up are described. Sample pre-concentration of 50-200 mL diluted automotive exhaust is performed using a triple phase “mixed bed” adsorption tube at O°C.

The settings of adaptive suspension elements may be switched from a comfortable “soft” characteristic to a safe and “firm” characteristic. Thus the possibility is given to not only improve the ride comfort, but the dynamic driving behavior as well, since no compromise must be made between these two criteria when tuning the suspensions. Such systems seem to be very promising for commercial vehicles, as - because of their changing loading conditions - it is very difficult to design an optimal suspension system using conventional springs and dampers. This paper describes the influence of shock absorbers and air springs with variable characteristics on the ride comfort and the dynamic behavior of a 15-t-truck by investigations done with a simulation system. A series production vehicle without adaptive suspension elements serves as basis. At first the results of measurements and simulations are compared and show a very good concurrence.

Economical and technical aspects justify intelligent suspension systems in commercial vehicles. The tasks of suspensions of vehicles are contradictionary and the prevailing problems cannot be readily solved with conventional suspension systems in a satisfying manner. However, advantages are acquired by the use of adaptive suspension systems. Varying the properties and characteristics of suspension systems in respect to the different loads transported by a commercial vehicle, to vehicle speeds and to dynamic maneuvers, nearly present as good results as closed loop controlled adaptive suspension systems do. For economical reasons fully active suspension systems are only installed in commercial vehicles performing special tasks and services. Partially active suspension systems reduce power consumption and demonstrate satisfactory efficiency.

The consequent means towards improved enhancement of the safety of commercial vehicles will in future times require more and more electronic intelligence, in case a distinct optimization of the systems will not be possible with conventional means. In forefront, endeavours are aimed at the improvements of the functions of the system in regard to driving safety, as well as driver stress relief at lowest possible costs, in order to increase the total cost effectiveness of commercial vehicles. Starting with currently implemented electronic systems up to systems now under development, a continuous development of standalone electronics up to integrated electronic compounding is the current trend. This trend shows advantages of reduced wiring and the number of sensors while it increases the function at the same time.

After the introduction of four-valve technology for gasoline powered passenger cars, Mercedes-Benz consistently developed this technology also for Diesel engines. Based on the proven success of the prechamber combustion system, this new Diesel engine generation, which includes 4, 5 and 6-cylinder naturally-aspirated engines, will be the first four-valve Diesel engines to be installed in passenger cars. The naturally aspirated 3.0 liter 6-cylinder in-line engine which represents the high end of this generation will be offered for sale in all 50 states of the USA in the Executive Class models starting on January 1, 1994. Four-valve technology allows the prechamber to be located centrally between the intake and exhaust valves which results in a major improvement of the combustion process. In addition, this 6-cylinder engine has a resonance intake system controlled by two butterfly valves to maximize the volumetric efficiency of the engine.

In particular on heavy duty commercial vehicles, the continuous braking systems “engine braking system” and “retarder”, which are independent of the service braking system, are installed to handle the continuous braking load on downhill stretches. These systems are also used to reduce lining wear and thermal loads of the service braking system. Exhaust braking systems are the most widely used form of engine braking systems. The current state-of-the-art in retarders is represented by two basic concepts, the electrodynamic retarder and the hydrodynamic retarder. A performance comparison of the different systems shows that low mountain descending speeds are the domain of engine braking systems, whereas retarders are more effective for medium and high descending speeds. The electrodynamic retarder is more favourable for lower road speeds, while the hydrodynamic retarder develops its effectiveness during higher downhill speeds.

During the past few years, economy of commercial vehicles has increased considerably due to higher engine outputs a+ lower engine speeds together with enhanced fuel economy. However, the average speed of commercial vehicles is not only determined by the speed attainable on level ground and on uphill gradients, but also to a large extent by the speed attainable on downhill gradients, with the latter depending on the available constant braking power. Since the displacement of commercial vehicle engines has not been increased or has even become smaller, their braking power has increased only slightly ot not at all. In order to enhance the overall economy of commercial vehicles, it was therefore necessary to increase the engine braking performance as well since the wheel brakes cannot be used for constant braking and additional systems for continuous operation are very complex.

Tires of modern commercial vehicles must meet a specific requirement profile, containing the economic aspects, ride comfort and driving safety, as well. These three primary criteria are discussed in this paper, whereby emphasis is placed on the force transmission behavior of commercial vehicle tires regarded as a variable directly associated to driving safety. At the same time, the influence of distinct parameters such as wheel load, road speed, tire inflation pressure, tread depth and coefficient of adhesion between tire and road on the lateral and braking force behavior is illustrated using steady state and dynamic measurements. They were carried out on real roads using a specially prepared mobile tire dynamometer, but on an indoor drum-type tire test stand, as well. In addition to the above mentioned parameter variations the differences of the results on account of the test method are analysed.

The shifting comfort of automatic transmissions of diesel engines at low temperatures can be substantially improved by using springs with temperature dependent rates in the control valves. These springs utilize the shape memory effect of Ni-Ti alloys. They provide a simple and economic way to control both shifting pressure and shifting time. The Mercedes- Benz automatic transmission uses two different springs with thermovariable rate (TVR) in the shifting pressure system to adapt the pressure in the switching elements to the lower torque of cold diesel engines. One spring is used in the shifting pressure control valve and one in the accumulator system.