Search Results

Since its implementation, exhaust gas recirculation has proven to be a reliable technique to control NOx emissions by lowering combustion temperature. Dilution with exhaust gas recirculation, whether in internal combustion engines or sequential-staged gas turbine combustors, affects flame reactivity and stability, which are related to the heat release rate and engine power. Another way to control emissions is to use hydrogen as a carbon-free alternative fuel, which is considered a milestone in the energy-decarbonization journey. However, the high reactivity of hydrogen is one of its hurdles and understanding this effect on laminar burning velocity is important. Flame propagation and burning velocity control the mixture reactivity and exothermicity and are related to abnormal combustion phenomena, such as flashback and knock. Therefore, understanding the effect of exhaust gas addition on the laminar burning velocity of hydrogen/air mixtures is imperative for engine design.

Autoignition delay times of two full blend gasoline fuels (high and low RON) were explored in a rapid compression machine. CO2 dilution by mass was introduced at 0%, 15%, and 30% levels with the O2:N2 mole ratio fixed at 1:3.76. This dilution strategy is used to represent exhaust gas recirculation (EGR) substitution in spark ignition (SI) engines by using CO2 as a surrogate for major EGR constituents(N2, CO2, H2O). Experiments were conducted over the temperature range of 650K-900K and at 10 bar and 20 bar compressed pressure conditions for equivalence ratios of (Φ =) 0.6-1.3. The full blend fuels were admitted directly into the combustion chamber for mixture preparation using the direct test chamber (DTC) approach. CO2 addition retarded the autoignition times for the fuels studied here. The retarding effect of the CO2 dilution was more pronounced in the NTC region when compared to the lower and higher temperature range.

Surface coatings are one of the most widely used routes to enhance the tribological properties of cylinder kits due to effective sealing capability with low friction coefficient and high wear resistance. In the current study, we have conducted the surface texture characterization of the coating on piston skirts and evaluated the impact of a novel Abradable Powder Coating (APC) on cylinder-kit performance in comparison to stock pistons. The surface texture and characteristic properties varying across the piston skirt are obtained and analyzed via a 3D optical profiler and OmniSurf3D software. The engine operating conditions are found through a combination of measurements, testing, and a calibrated GT-Power model. The variable surface properties along with other dimensions, thermodynamic attributes, flow characteristics and material properties are used to build a model in CASE (Cylinder-kit Analysis System for Engines)- PISTON for both an APC coated piston and a stock piston.

Cylinder-kit tribology has been a significant focus in developing internal combustion engines of lower emission, reduced friction and oil consumption, and higher efficiency. This work addresses the impact of ring-groove geometry on oil (liquid oil and oil vapor) transport and combustion gas flow in the cylinder kit, using a dynamic three-dimensional multiphase modeling methodology during the four-stroke cycle of a piston engine. The ring and groove geometry, along with the temperature and pressure conditions at the interface between piston and liner, trigger the oil and gas (combustion gases and oil vapor) transport. A study of the second ring dynamics is presented to investigate the effect of negative ring twist on the three-dimensional fluid flow physics. The oil (liquid oil and oil vapor) transport and combustion gas flow processes through the piston ring pack for the twisted and untwisted geometry configurations are compared.

Mixture formation and combustion dynamics are the primary contributors to the performance and emission characteristics of direct-injected spark ignition (SI) engines. This requires assessing the benefits and tradeoffs of the design and control factors that influence mixing and the subsequent combustion event. In this study, Taguchi's L18 orthogonal array design of experiment (DoE) methodology has been applied to assess contributions and tradeoffs of varied compression ratio, piston bowl design, intake port tumble design, injector spray pattern, injection timing, injection pressure, exhaust gas recirculation (EGR) rate, and intake valve closing timing in a single-cylinder boosted gasoline direct injection (GDI) SI engine. This multiparameter study has been carried out across three speed-load conditions representative of typical automotive application operating ranges.

Rapid Compression Machines (RCM) offer the ability to easily change the compression ratio and the pressure/mixture composition/temperature to gather ignition delay data at various engine relevant conditions. Therefore, RCMs with optical access to the combustion chamber can provide an effective way to analyze macroscopic spray characteristics needed to understand the spray injection process and for spray model development, validation and calibration at conditions that are suitable for engines. Fuel surrogates can help control fuel parameters, develop models for spray and combustion, and perform laser diagnostics with known fluorescence characteristics. This study quantifies and evaluates the macroscopic spray characteristics of multicomponent gasoline surrogates in comparison to their gasoline counterparts, under gasoline direct injection (GDI) engine conditions.

In this work autoignition delay times of two multi-component surrogates (high and low RON) were experimentally compared with their target full blend gasoline fuels. The study was conducted in a rapid compression machine (RCM) test facility and a direct test chamber (DTC) charge preparation approach was used for mixture preparation. Experiments were carried over the temperature range of 650K-900K and at 10 bar and 20 bar compressed pressure conditions for equivalence ratios of (Φ =) 0.6-1.3. Dilution in the reactant mixture was varied from 0% to 30% CO2 (by mass), with the O2:N2 mole ratio fixed at 1:3.76. This dilution strategy emulates exhaust gas recirculation (EGR) substitution in spark ignition (SI) engines. The multicomponent surrogate captured the reactivity trends of the gasoline-air mixtures reasonably well in comparison to the single component (iso-octane) surrogate.

Charge dilution is widely considered as one of the leading strategies to realize further improvement in thermal efficiency from current generation spark ignition engines. While dilution with excess air (lean burn operation) provides substantial thermal efficiency benefits, drastically diminished NOx conversion efficiency of the widely used three-way-catalyst (TWC) during off-stoichiometric/lean burn operation makes the lean combustion rather impractical, especially for automotive applications. A more viable alternative to lean operation is the dilution with EGR. The problem with EGR dilution has been the substantially lower dilution tolerance limit with EGR and a consequent drop in thermal efficiency compared to excess air/lean operation. This is particularly applicable to the pre-chamber jet ignition technologies with considerably higher lean burn capabilities but much lower EGR tolerance due to the presence of a high fraction of residuals inside the pre-chamber.

Understanding cylinder-kit tribology is pivotal to durability, emission management, reduced oil consumption, and efficiency of the internal combustion engine. This work addresses the understanding of the fundamental aspects of oil transport and combustion gas flow in the cylinder kit, using simulation tools and high-performance computing. A dynamic three-dimensional multi-phase, multi-component modeling methodology is demonstrated to study cylinder-kit assembly tribology during the four-stroke cycle of a piston engine. The percentage of oil and gas transported through different regions of the piston ring pack is predicted, and the mechanisms behind this transport are analyzed. The velocity field shows substantial circumferential flow in the piston ring pack, leading to blowback into the combustion chamber during the expansion stroke.

Continuous efforts to improve thermal efficiency and reduce exhaust emissions of internal combustion engines have resulted in development of various solutions towards improved lean burn ignition systems in spark ignition engines. The Dual Mode, Turbulent Jet Ignition (DM-TJI) system is one of the leading technologies in that regard which offers higher thermal efficiency and reduced NOx emissions due to its ability to operate with very lean or highly dilute mixtures. Compared to other pre-chamber ignition technologies, the DM-TJI system has the distinct capability to work with a very high level of EGR dilution (up to ~40%). Thus, this system enables the use of a three-way catalyst (TWC). Auxiliary air supply for pre-chamber purge allows this system to work with such high EGR dilution rate. This work presents the results of experimental investigation carried out with a Dual Mode, Turbulent Jet Ignition (DM-TJI) optical engine equipped with a cooled EGR system.

Ignition delay, using a rapid compression machine (RCM), is defined as the time period between the end of compression and the maximum rate of pressure rise due to combustion, at a given compressed condition of temperature and pressure. The same compressed conditions can be reached by a variety of combinations of compression ratio, initial temperature, initial pressure, diluent gas composition, etc. It has been assumed that the value of ignition delay, for a given fuel and at a given set of compressed conditions, would be the same, irrespective of the variety of the above-mentioned combinations that were used to achieve the compressed conditions. In this study, a range of initial conditions and compression ratios are studied to determine their effect on ignition delay time and to show how ignition delay time can differ even at the same compressed conditions.

Spherically expanding flames are employed to measure the laminar flame speed of premixed iso-octane/air mixtures at elevated temperatures through both experiments and numerical simulations. Iso-octane (2,2,4-trimethlypentane) is an important gasoline primary reference fuel (PRF). While most studies on laminar burning velocity of iso-octane focus on low temperatures (less than 400 K), the experiments here were conducted in an optically accessible constant volume combustion chamber between 373 K-473 K, at a pressure of 1 bar, and from ϕ=0.8 to ϕ=1.6. The effect of diluent is investigated through the addition of 15% CO2 dilution in order to simulate the effect of exhaust gas recirculation. The decreased reactivity with diluent addition reduces mixture reactivity, which can reduce the propensity for knock in spark ignition engines. All laminar flame speeds were calculated using the constant pressure method enabled via schlieren visualization of the spherically propagating flame front.

The fluid motion inside the engine cylinder is transient, three-dimensional and highly turbulent. It is also well known that cycle-to-cycle flow variations have a considerable influence on cycle-to-cycle combustion variations. Laser-based diagnostic techniques, for example, particle image velocimetry (PIV) or molecular tagging velocimetry, can be used to measure two or three components of the velocity field simultaneously at multiple locations over a plane. The use of proper orthogonal decomposition (POD) allows quantification of cycle-to-cycle flow variations, as demonstrated using PIV data [1]. In the present work, POD is used to explore the cycle-to-cycle flow variations utilizing molecular tagging velocimetry data. The instantaneous velocity fields were obtained over a swirl measurement plane when engine was operated at 1500 rpm and 2500 rpm.

Piston temperature plays a major role in determining details of fuel spray vaporization, fuel film deposition and the resulting combustion in direct-injection engines. Due to different heat transfer properties that occur in optical and all-metal engines, it becomes an inevitable requirement to verify the piston temperatures in both engine configurations before carrying out optical engine studies. A novel Spot Infrared-based Temperature (SIR-T) technique was developed to measure the piston window temperature in an optical engine. Chromium spots of 200 nm thickness were vacuum-arc deposited at different locations on a sapphire window. An infrared (IR) camera was used to record the intensity of radiation emitted by the deposited spots. From a set of calibration experiments, a relation was established between the IR camera measurements of these spots and the surface temperature measured by a thermocouple.

High frequency variations in crankcase pressure have been observed in Inline-four cylinder (I4) engines and an understanding of the causes, frequency and magnitude of these variations is helpful in the design and effective operation of various engine systems. This paper shows through a review and explanation of the physics related to engine operation followed by comparison to measured vehicle data, the relationship between crankcase volume throughout the engine cycle and the observed pressure fluctuations. It is demonstrated that for a known or proposed engine design, through knowledge of the key engine design parameters, the frequency and amplitude of the cyclic variation in crankcase pressure can be predicted and thus utilized in the design of other engine systems.

Three-dimensional numerical simulation of the turbulent jet ignition combustion process of a premixed methane-air mixture in a Rapid Compression Machine (RCM) was performed using the Converge computational software. Turbulent jet ignition is a prechamber initiated combustion system that can replace the spark plug in a spark ignition engine. The prechamber is a small volume chamber where an injector and spark plug are located and is connected to the main combustion chamber via one or multiple small orifices. Turbulent jet ignition is capable of enabling low temperature combustion, through either lean or dilute combustion. A RANS model, which included a k-ε turbulence model to solve the mean flow and the SAGE chemistry solver with a reduced methane mechanism to solve the chemistry, was used to model the turbulent jet ignition system.

Turbulent jet ignition is a pre-chamber ignition enhancement method that produces a distributed ignition source through the use of a chemically active turbulent jet which can replace the spark plug in a conventional spark ignition engine. In this paper combustion visualization and characterization was performed for the combustion of a premixed propane/air mixture initiated by a pre-chamber turbulent jet ignition system with no auxiliary fuel injection, in a rapid compression machine. Three different single orifice nozzles with orifice diameters of 1.5 mm, 2 mm, and 3 mm were tested for the turbulent jet igniter pre-chamber over a range of air to fuel ratios. The performance of the turbulent jet ignition system based on nozzle orifice diameter was characterized by considering both the 0-10 % and the 10-90 % burn durations of the pressure rise due to combustion.

A three-dimensional piston ring model has been developed using finite element method with eight-node hexahedral elements. The model predicts the piston ring conformability with the cylinder wall as well as the separation gap between the interfaces if existing in the radial direction. In addition to the radial interaction between the ring front face and the cylinder wall, the model also predicts the contact between the ring and groove sides in the axial direction. This means, the ring axial lift, ring twist, contact forces with the groove sides along the circumferential direction are all calculated simultaneously with the radial conformability prediction. The ring/groove side contact can be found for scraper ring at static condition, which is widely used as the second compression ring in a ring pack. Thermal load is believed having significant influence on the ring pack performance.

Camless Variable Valve Actuation (VVA) technologies have been known for improving fuel economy, reducing emissions, and enhancing engine performance. VVA can be divided into electro-magnetic, electro-hydraulic, and electro-pneumatic actuation. A family of camless VVA designs (called LGD-VVA or Gongda-VVA) has been presented in an earlier SAE publication (SAE 2007-01-1295) that consists of a two-spring actuation, a bypass passage, and an electrohydraulic latch-release mechanism. The two-spring pendulum system is used to provide efficient conversion between the moving mass kinetic energy and the spring potential energy for reduced energy consumption and to be more robust to the operational temperature than the conventional electrohydraulic actuation; and the electrohydraulic mechanism is intended for latch-release function, energy compensation and seating velocity control.

An experimental study has been conducted to quantify the velocity and pressure inside an idealized intake manifold of a motored internal combustion engine assembly. The aim of this work is to provide the real-time boundary conditions for more accurate multi-dimensional numerical simulations of complex in-cylinder flows in an internal combustion engine as well as the resultant in-cylinder flow patterns. The geometry of the intake manifold is simplified for this purpose. A hot-wire anemometer and a piezoresistive absolute pressure transducer are used to measure the velocity and pressure, respectively, over a plane inside the circular section of the intake manifold. In addition, pressure measurements are performed over an elliptical section near the intake port. Phase-averaged velocity and pressure profiles are then calculated from the instantaneous measurements. Experiments were performed at 900 and 1200 rpm engine speeds with wide open throttle.