Search Results

Dynamical Energy Analysis (DEA) has recently been introduced as a mesh-based high frequency method modelling structure borne sound for complex built-up structures. Using DEA, the structure-borne sound of an assembled agricultural tractor was calculated and good agreement between measurement and DEA calculations has been shown. However, it is still difficult to model a solid structure as currently DEA is based on wave-transmission calculations through plates and plate-to-plate junctions. Additionally, it is often difficult to generate accurate FE meshes of assembled complex structures because of welds, bolts, and rubber brushes between components. In this paper, we propose a novel method to generate DEA elements based on measurement data in order to model solid parts of a complex structures. The method of Advanced Transfer Path Analysis (ATPA) is employed to extract energy-transmission characteristics of a structure.

The Composite Lightweight Automotive Suspension System is a composite rear suspension knuckle/tieblade consisting of UD prepreg (epoxy resin), SMC (vinylester resin) carbon fibre and a steel insert to reduce the weight of the component by 35% and reduce Co2. The compression moulding manufacturing process and CAE optimisation are unique and ground-breaking for this product and are designed to allow high volume manufacture of approx. 30,000 vehicles per year. The manufacturing techniques employed allow for multi-material construction within a five minute cycle time to make the process viable for volume manufacture. The complexities of the design lie in the areas of manufacturing, CAE prediction and highly specialised design methods. It is a well-known fact that the performance of a composite part is primarily determined by the way it is manufactured.

NVH requirements are critical in new driveline developments. Failure modes due to resonances must be carefully analyzed and potential root causes must have adequate countermeasures. One of the most common root causes is the modal alignment. This work shows the steps to design and optimize a new plastic bracket for an automotive half shaft bearing. This bracket replaces a very stiff bracket, made of cast iron. The initial design of plastic bracket was not stiff enough to bring natural frequency of the system above engine second order excitation at maximum speed. The complete power pack was modeled and NVH CAE analysis was performed. The CAE outputs included Driving Point Response, Frequency Response Function and Modal analysis. The boundary conditions were discussed deep in detail to make sure the models represented actual system.

The modeling of plastic fuel tank systems for crash safety applications has been very challenging. The major challenges include the prediction of fuel sloshing in high speed impact conditions, the modeling of multilayer thermoplastic fuel tanks with post-forming (non-uniform) material properties, and the modeling of tank straps with pre-tensions. Extensive studies can be found in the literature to improve the prediction of fuel sloshing. However, little research had been conducted to model the post-forming fuel tank and to address the tension between the fuel tank and the tank straps for crash safety simulations. Hoping to help improve the modeling of fuel systems, the authors made the first attempt to tackle these major challenges all at once in this study by dividing the modeling of the fuel tank into eight stages. An ALE (Arbitrary Lagrangian-Eulerian) method was adopted to simulate the interaction between the fuel and the tank.

When considering ride comfort and precision there are lots of components in the vehicle suspensions that have influence in this behavior and some ride occurrences (mainly higher frequencies) are rubber bushing responsibility but due their compliance, other vehicle attributes, steering and handling, can be affected. So the correct components tuning can maintain or improve vehicle attributes to address desired brand DNA and vehicle its specific needs. These studies were done considering the elastokinematics of front axle only due need of improve its comfort concerning higher frequencies (impacts and harshness). In addiction, correlation between subjective evaluation and objective data acquisition/post processing is desirable to optimize development time. Based in subjective directional, the activities time was reduced and final configuration reached faster.

This paper studies the feasibility and potential benefits of aligning recycled carbon fibres, in the form of short individual filaments, to manufacture fibre reinforced polymer composites. A review of fibre alignment processes is presented to provide insight into the different alignment technologies. The main focus is on wet hydrodynamic processes, which offer a high degree of alignment for discontinuous fibres. The process parameters that govern the alignment efficiency are also reported. The effect of alignment on fibre packing efficiency in the manufacture of composites is included, together with a report of preliminary fibre alignment results obtained from three different alignment processes.

The intent of this paper is to summarize the work of the V8 power plant intake manifold radiated noise study. In a particular V8 engine application, customer satisfaction feedback provided observations of existing unpleasant noise at the driver's ear. A comprehensive analysis of customer data indicated that a range from 500 to 800 Hz suggests a potential improvement in noise reduction at the driver's ear. In this study the noise source was determined using various accelerometers located throughout the valley of the engine and intake manifold. The overall surface velocity of the engine valley was ranked with respect to the overall surface velocity of the intake manifold. An intensity mapping technique was also used to determine the major component noise contribution. In order to validate the experimental findings, a series of analysis was also conducted. The analysis model included not only the plastic intake manifold, but also the whole powertrain.

As automotive manufacturers continue to increase their use of thermoplastics for interior and exterior components, there is a likelihood of squeaks due to material contacts. To address this issue, Ford's Body Chassis NVH Squeak and Rattle Prevention Engineering Department has developed a tester that can measure friction, and any accompanying audible sound, as a function of sliding velocity, normal load, surface roughness, and environmental factors. The Ford team has been using the tester to address manufacturing plant issues and to develop a database of polymeric material pairings that will be used as a guide for current and future designs to eliminate potential noise concerns. Based upon the database, along with a physical property analysis of the various plastic (viscoelastic) materials used in the interior, we are in the process of developing an analytical model which will be a tool to predict frictional behavior.

Using the results of Constant Temperature (CT) Permeation Measurements to estimate Real Time Diurnal (RTD) permeation emissions has a number of practical advantages. In particular, Constant Temperature measurements are easier to set up and control in a laboratory environment, and Constant Temperature measurements provide for data checks using simple self-consistency tests that are not possible with Real Time Diurnal measurements. Furthermore, there is no need to repeat permeation measurements for each separate real-time temperature profile of interest. The same two Constant Temperature measurements can be used to estimate permeation performance for many different temperature cycles - for example, the temperature cycles prescribed by CARB, EPA, and EEC, or the different temperature profiles experienced by separate fuel system components during a vehicle SHED test.

In 1998, the United States Field Trial was chartered by the United States Council for Automotive Research/Vehicle Recycling Partnership with the objective of evaluating the feasibility of collecting and recycling automotive polymers from domestic end-of-life Vehicles (ELVs). Although ELVs are among the most widely recycled consumer products, 15-25% of their total mass must nevertheless be disposed of with no material recovery; the majority of this remainder is polymeric. Concerns regarding vehicle abandonment risks and disposal practices have resulted in the legislated treatment of ELVs in Western Europe, and in the emergence of attendant material recycling schemes. These schemes support quantitatively optimized material collection, but do not appear to be sustainable under the free-market economic conditions prevalent in North America.

Predicting the service lifetime of elastomeric automotive components is key to improving customer satisfaction over a 10 year / 150,000 mile desired lifetime. Achieving a good correlation between artificially aged components and those which have seen real customer usage can be a daunting task, considering the possible variations in climate, exposure and driver aggressiveness. In natural rubber (NR) components, the quantity and structure of the network crosslinks as a function of time can be used to explore some of the most basic aging mechanisms seen in the real world, as well as to validate protocols developed within the laboratory environment to accelerate the simulation of real-world mechanisms. This paper explores the findings of such a study on an NR engine mount, and examines the information learned by comparison between actual used components and test specimens subjected to accelerated degradation.

The effect of suspension system parameters on NVH performance is presented using the results of a design of experiments analysis of a quarter-car model with elastomeric elements. The elastomeric elements are modeled using Maxwell elements with stiffness increasing with frequency. Fourteen design parameters are considered. The force spectrum acting on the sprung mass is partitioned into frequency bands. The amplitude in each frequency band as well as location and amplitudes of resonance peaks in the force spectrum are used as response variables. Major factors that effect each response variable are quantified using sensitivity coefficients. Constrained optimization studies were run to identify the minimum and maximum responses that can be expected. Suspension and bushing designers can use this work to estimate the behavior of design alternatives early in the design process.

Squeak and rattle has become a primary source of undesired noise in automobiles due to the continual diminishment of engine, power train and tire noise levels. This article presents a finite-element-based methodology for the improvement of rattle performance of vehicle components. For implementation purposes, it has been applied to study the rattle of a glove compartment latch and corner rubber bumpers. Results from the glove compartment study are summarized herein. Extensions to other rattle problems are also highlighted.

Experimental forms of two different types of engine oil viscosity sensors have been tested that use uniformly poled disks of piezoelectric PZT ceramic. In both cases, the disks were used to form electromechanical resonators functioning as the frequency-controlling element in a transistor oscillator circuit. The simpler type of sensor used only one disk, vibrating in a radial-longitudinal mode of vibration. In this mode, a disk 2.54 cm in diameter and 0.127 cm thick had a resonant frequency of approximately 90 kHz. The second type of sensor used two such disks bonded together by a conducting epoxy, with poling directions oriented in opposite directions. This composite resonator vibrated in a radially-symmetrical, flexural mode of vibration, with the lowest resonant frequency at approximately 20 kHz. The presence of tangential components of motion on the major faces of both resonators made them sensitive to the viscosity of fluids in which they were immersed.

One of the methods used to mechanically fasten a component such as a radio, cluster or finish panel to a plastic instrument panel substrate involves driving a screw through a metal push-nut which has been inserted into an opening in the plastic instrument panel substrate. A primary failure mode which has been observed for this type of joint is cracking of the plastic substrate surrounding the metal push-nut. Finite Element Analysis (FEA) has been employed to optimize the design of the push-nut opening in a polycarbonate substrate and minimize the potential for cracking of the plastic. For the FEA, the implicit version of the ABAQUS program was used. It was determined that the induced stress in the plastic instrument panel substrate from the fastening process can be minimized by controlling the dimensions of the push-nut opening such that push-nut recess is minimized and the thickness of the substrate in the region whether the push-nut engages is optimized.

EcoPlus™ Automotive Carpet Systems, are used in trunks, on floors, for throw in mats, and more and contain many different thermoplastics polymers in various forms. New technologies are being developed to recycle complex carpet systems. One system has been evaluated at the Vehicle Recycling Partnership using a “remelt’ recycling process which can be used on a wide variation of thermoplastic materials, or blends of thermoplastic materials. The remelt process takes normally incompatible thermoplastic polymers and makes them compatible in a homogenous mix. This proprietary process yields a useable plastic. Plastic made from automotive carpet systems can be used to manufacture new automotive parts or other plastic articles of commerce.

The 1997 Ford Explorer introduces a new two valve single overhead cam (SOHC) version of the 4.0L V6 engine. Maximum power output is increased to 153 KW net (205 HP) at 5000 rpm and 340 N-M of torque (250 lb-ft) at 3000 rpm, which represents a 28% increase in power and an 11% increase in torque over the existing 4.0L overhead valve (OHV) design. The new design's performance features are single overhead camshafts driven by a patented “Offset Y-drive” dual stage chain system, a plastic variable induction system, and aluminum cylinder heads. For quieter and smoother operation, a main bearing ladder frame and a unique second-order balance shaft (4x4 only) are added.

Because it is common to attach plastic parts to other plastic, metal, or ceramic assemblies with mechanical fasteners that are often stronger and stiffer than the plastic with which they are mated, it is important to be able to predict the retention of the fastener in the polymeric component. The ability to predict this information allows engineers to more accurately estimate length of part service life. A study was initiated to understand the behavior of threaded fasteners in bosses molded from engineering thermoplastic resins. The study examined fastening dynamics during and after insertion of the fastener and the effects of friction on the subsequent performance of the resin. Tests were conducted at ambient temperatures over a range of torques and loads using several fixtures that were specially designed for the study. Materials evaluated include modified-polyphenylene ether (M-PPE), polyetherimide (PEI), polybutylene terephthalate (PBT), and polycarbonate (PC).

High mileage NVH performance is one of the major concerns in vehicle design for long term customer satisfaction. Elastomeric components such as suspension bushings function as vibration isolators in a vehicle. High mileage driving tends to cause the degradation of these components which in turn results in the degradation of vehicle overall NVH performance. The present paper presents the application of CAE based robustness methodology to vehicle high mileage degradation with respect to bushing degradation. A unitized vehicle with suspension strut mounts is selected as the project vehicle. Strut mount degradation characteristics, vehicle CAE model and design of experiment are linked together to achieve vehicle response robustness. The concept and methodology arc demonstrated using a tire input which simulates road excitations as a first step toward the development of a more extensive robustness methodology which will cover other excitation conditions.

High mileage NVH performance is one of the major concerns in vehicle design for long term customer satisfaction. Elastomeric components such as suspension bushings, engine mounts and tires function as vibration isolators in a vehicle. High mileage tends to cause the degradation of these components which in turn affects vehicle overall NVH performance. The present paper discusses the characteristics of bushing degradation based on laboratory bushing test data. Vehicle subjective evaluation and CAE modeling methods are used to develop a fundamental understanding of the effects of bushing degradation on vehicle NVH performance. The concept and analysis methodology are demonstrated using the front and rear suspension strut mounts and tire inputs which simulate road excitations but they are valid for other elastomeric components such as engine mounts and excitations. The knowledge derived in the study can be used as a generic guideline in designing vehicles for high mileage NVH robustness.