Search Results

In the face of growing concerns about environmental sustainability and urban congestion, the integration of eco-driving strategies has emerged as a pivotal solution in the field of the urban transportation sector. This study explores the potential benefits of a CAV functioning as a virtual eco-driving controller in an urban traffic scenario with a group of following human-driven vehicles. A computationally inexpensive and realistic powertrain model and energy management system of the Chrysler Pacifica PHEV are developed with the field experiment data and integrated into a forward-looking vehicle simulator to implement and validate an eco-driving speed planning and energy management strategy assuming longitudinal automation. The eco-driving algorithm determines the optimal vehicle speed profile and energy management strategy.

Battery terminal voltage modelling is crucial for various applications, including electric vehicles, renewable energy systems, and portable electronics. Terminal voltage models are used to determine how a battery will respond under load and can be used to calculate run-time, power capability, and heat generation and as a component of state estimation approaches, such as for state of charge. Previous studies have shown better voltage modelling accuracy for long short-term memory (LSTM) recurrent neural networks than other traditional methods (e.g., equivalent circuit and electrochemical models). This study presents two new approaches – sequence training and data shuffling – to improve LSTM battery voltage models further, making them an even better candidate for the high-accuracy modelling of lithium-ion batteries. Because the LSTM memory captures information from past time steps, it must typically be trained using one series of continuous data.

This paper delves into the investigation of flatness-based active damping control for hybrid vehicle transmissions. The main objective is to improve the current in-production controller performances without the need for additional sensors or observers. The primary goals include improving torque setpoint tracking, enhancing robustness margins, and ensuring zero steady-state torque correction. The investigation proceeds in several steps: Initially, both the general differential flatness property and the identification of flat outputs in linear dynamical systems are revisited. Subsequently, the bond graph formalism is employed to deduce straightforwardly the dynamical equations of the system. Next, a new flat output of the vehicle transmission is identified and utilized to formulate the trajectory tracking controller to align with the required control objectives and to fulfill the system constraints.

Threat Analysis Risk Assessment (TARA) for automotive systems is standardized in ISO/SAE 21434. Traditionally these analyses have been bifurcated into either analysis focused on system functionality identifying impacts to assets based on the mission of the product, or analysis targeting vulnerabilities associated with the hardware and software of interfaces selected to be a part of a product. Furthermore, in the age of Software Defined Vehicles, the challenges to decouple use cases and the software that implements such from specific fixed hardware designs magnifies the disconnect between these risk methods. Use Case Based threat analysis, grounded in understanding features, stakeholders, and user stories, inherently yields security requirements tailored to specific functionalities and their contexts.

The modern automotive industry field is in the middle of a major transformation of the Electric/Electronics (E/E) system design, to meet the future mobility trends driven by Autonomy, Electrification and expanded Connectivity. For these reasons, the ongoing industry trend is to move to more centralized E/E architectures by combining and integrating sub-systems and controllers, from either a functional domain standpoint (horizontal integration, or “cross-domain controllers”) or a geographical zone standpoint (vertical integration, or “central brain with zones”), with the objective to optimize cost, weight, power distribution, provide enhanced security and versatility. This is because electrification, autonomy and connectivity features are significantly increasing the demand for data processing bandwidth, network throughput, intelligent power distribution and wiring harness capabilities for additional sensors/actuators.

Battery packs used in automotive application experience high-power demands, fast charging, and varied operating conditions, resulting in temperature imbalances that hasten degradation, reduce cycle life, and pose safety risks. The development of proper simulation tools capable of capturing both the cell electrical and thermal response including, predicting the cell’s temperature rise and distribution, is critical to design efficient and reliable battery packs. This paper presents a co-simulation model framework capable of predicting voltage, 2-D heat generation and temperature distribution throughout a cell. To capture the terminal voltage and 2-D heat generation across the cell, the simulation framework employs a high-fidelity electrical model paired with a charge balance model based on the Poisson equation. The 2-D volumetric heat generation provided by the charge balance model is used to predict the temperature distribution across the cell surface using CFD software.

A new optical array imaging probe, called the 1D2D probe, has been developed by Science Engineering Associates, with features added to improve the real-time and post-analysis measurements of particle spectra, particularly in the Supercooled Large Droplet size range. The probe uses optical fibers and avalanche photodiodes to achieve a very high frequency response, and a Field-Programmable Gate Array that performs real-time particle rejection and processing of accepted particles with negligible inter-particle dead time. The probe records monochromatic two-dimensional images, while also recording the number of individual particle pixels at a second grey scale level. The probe implements flexible features to filter recording of highly out of focus particles to improve the accuracy of particle size determination, or to reject small particles to improve the statistics of measurements of larger particles.

With electromobility, vehicles are becoming quieter due to the presence of electric motors that replace internal combustion engines. The interior cabin noise of electric vehicles is characterized by high-frequency components that can be annoying and unpleasant. Therefore, it is essential to analyse the NVH behaviour of e-powertrains early in the design-phase. However, this induces inherent uncertainties during the design process related to the operating conditions, geometrical parameters, measurement techniques, etc. that need to be quantified with fast and comprehensive stochastic models. In this work, we first present a deterministic framework to provide first-order estimations of the e-powertrain’s interior whining noises, combining both the airborne & structure-borne contribution with data-driven NVH transfers meta-models.

The National Aeronautics and Space Administration (NASA) remotely administered a psychoacoustic test in fall of 2022 as the first of two phases of a cooperative Urban Air Mobility (UAM) vehicle noise human response study. This first phase, described here, was a Feasibility Test to compare human subject responses with a previous in-person psychoacoustic test that found an annoyance response difference between small Uncrewed Aerial System (sUAS) noise and ground vehicle noise. This paper discusses the Feasibility Test online layout, sound calibration method, software development, stimuli selection, test subject recruitment, and test administration. Test performance is measured through comparison of annoyance response data with the previous in-person test. The test also investigated whether a contextual cue to test subjects influenced their annoyance response. Response differences between test subjects in geographically distinct areas are analyzed.

1 Autonomous Driving Systems (ADS) are developing rapidly. As vehicle technology advances to SAE level 3 and above (L4, L5), there is a need to maximize and verify safety and operational benefits. As a result, maintenance of these ADS systems is essential which includes scheduled, condition-based, risk-based, and predictive maintenance. A lot of techniques and methods have been developed and are being used in the maintenance of conventional vehicles as well as other industries, but ADS is new technology and several of these maintenance types are still being developed as well as adapted for ADS. In this work, we are presenting a systematic literature review of the “State of the Art” knowledge for the maintenance of a fleet of ADS which includes fault diagnostics, prognostics, predictive maintenance, and preventive maintenance.

For realistic traffic modeling, real-world traffic calibration data is needed. These data include a representative road network, road users count by type, traffic lights information, infrastructure, etc. In most cases, this data is not readily available due to cost, time, and confidentiality constraints. Some open-source data are accessible and provide this information for specific geographical locations, however, it is often insufficient for realistic calibration. Moreover, the publicly available data may have errors, for example, the Open Street Maps (OSM) does not always correlate with physical roads. The scarcity, incompleteness, and inaccuracies of the data pose challenges to the realistic calibration of traffic models. Hence, in this study, we propose an approach based on spatial interpolation for addressing sparsity in vehicle count data that can augment existing data to make traffic model calibrations more accurate.

Car interior noise performances, such as booming noise and rolling noise, are usually computed in mid-low frequency range by multiplying vehicle vibroacoustic FRFs and the source (powertrain and chassis) blocked force spectrum. Unfortunately, during the early design stages, the cavity as well as some car body parts’ (like panels) are still subject to geometrical changes that do not allow a full vibrocoustic CAE analysis. Nevertheless, it has been shown that even in the low frequency range the vehicle response remains proportional to the mechanical injected power into the vehicle. The Power Frequency Response Functions was introduced in order to link the energy response of the vehicle to the injected power. Then, decreasing the injected power -without any consideration to the panels and cavity coupled responses- will ensure a noise reduction. The first part of this paper will introduce the injected power and power frequency response functions computation, using vibroacoustic FE models.

Testing any new safety technology of Autonomous Vehicles (AV) and Advanced Driver Assistance Systems (ADAS) requires simulation-based validation and verification. The specific scenarios used for testing, outline incidences of accidents or near-miss events. In order to simulate these scenarios, specific values for all the above parameters are required including the ego vehicle model. The ‘criticality’ of a scenario is defined in terms of the difficulty level of the safety maneuver. A scenario could be over-critical, critical, or under-critical. In over-critical scenarios, it is impossible to avoid a crash whereas, for under-critical scenarios, no action may be required to avoid a crash. The criticality of the scenario depends on various parameters e.g. speeds, distances, road/tire parameters, etc. In this paper, we propose a definition of criticality metric and identify the parameters such that a scenario becomes critical.

In the last decade, the use of Driver-in-the-Loop (DiL) simulators has significantly increased in research, product development, and motorsports. To be used as a verification tool in research, simulators must show a level of correlation with real-world driving for the chosen use case. This study aims to assess the validity of a low-cost, limited travel Vehicle Dynamics Driver-in-Loop (VDDiL) simulator by comparing on-road and simulated driving data using a statistical evaluation of longitudinal and lateral metrics. The process determines if the simulator is appropriate for verifying control strategies and optimization algorithms for longitudinal vehicle dynamics and evaluates consistency in the chosen metrics. A validation process explaining the experiments, choice of metrics, and analysis tools used to perform a validation study from the perspective of the longitudinal vehicle model is shown in this study.

A new method is presented for developing proving ground durability tests for electrified vehicle (xEV) drivetrains. For xEVs, the durability tests must be able to capture the added driveline torques due to regenerative braking, customer battery charge/recharge usage, and battery power degradation over time. In terms of xEV duty cycle test schedule development, using actual vehicle data from specific proving ground test events might prove to be costly and time consuming. Furthermore, newer electrified prototype vehicles might not be available for trackside testing while still undergoing the design stage. The new method presented here aims to reduce the complexities of xEV proving ground duty cycle development with the use of a high-fidelity vehicle dynamics simulation model for electrified powertrains.

As centralization of automotive E/E (Electrical and/or Electronic) architectures becomes reality for future vehicles, it is crucial that existing assets be reused in the most efficient and effective manner. We report on our experience developing a new centralized E/E architecture for a propulsion domain, and migrating the corresponding propulsion elements of an existing decentralized, CAN-based architecture to a prototype of the centralized propulsion domain. Our migration adopts automotive Ethernet and supporting standards as a next-generation communications backbone technology; a next-generation computation platform from automotive supplier NXP; and a new automotive virtualization solution from OpenSynergy. We discuss aspects of legacy software reuse and adaptation; modification of vehicle HiL simulation models used in testing; existing vendor tool support; and implications arising from functional safety and the ISO 26262 standard.

To improve the biofidelity of the currently available Hybrid III 10-year-old (HIII-10C) Anthropomorphic Test Device (ATD), the National Highway Traffic Safety Administration (NHTSA) has developed the Large Omnidirectional Child (LODC) ATD. The LODC head is a redesigned HIII-10C head with mass properties and modified skin material required to match pediatric biomechanical impact response targets from the literature. A dynamic, nonlinear finite element (FE) model of the LODC head has been developed using the mesh generating tool Hypermesh based on the three-dimensional CAD model. The material data, contact definitions, and initial conditions are defined in LS-PrePost and converted to LS-Dyna solver input format. The aluminum head skull is stiff relative to head flesh material and was thus modeled as a rigid material. For the actual LODC, the head flesh is form fit onto the skull and held in place through contact friction.

Second-life batteries (SLBs, automotive batteries that have lost their usefulness for vehicular applications) can provide low-cost environment-friendly solutions for grid-connected systems. The estimation of the remaining useful life (RUL) of SLBs is a fundamental step for the development of appropriate business models. This paper aims at unveiling correlations between the SLB's power profile and aging performance by defining appropriate metrics. A widely accepted empirical degradation model, that can predict calendar and cycling aging, is considered for this study. Several grid-connected power profiles are analyzed, such as peak shaving for DC-fast charge stations and frequency regulation. The results of this analysis show a correlation between the SLB's replacement rate with the minimum daily SoC.

A single-vehicle crash involving an SUV led to the study of the failure of the anti-sway bar linkage and tire pressure and their relative effects on the handling characteristics of the vehicle. The SUV, having been involved in a rollover, was found with the anti-sway bar drop link disconnected from the suspension lower A-arm assembly. Also, after the crash, the tire pressure in the front tires on the subject vehicle was measured to be above the value specified by the SUV manufacturer; however, the pressure for one of the rear tires was measured to be roughly half of the SUV manufacturer’s recommended pressure. The other rear tire was deflated. The testing described herein addresses the question of what effects the anti-sway bar drop link disconnection or reduced rear axle tire pressure would have on the SUV’s pre-accident handling and driveability.

This paper focuses on finding and analyzing the relevant parameters affecting traffic flow when autonomous vehicles are introduced for ride hailing applications and autonomous shuttles are introduced for circulator applications in geo-fenced urban areas. For this purpose, different scenarios have been created in traffic simulation software that model the different levels of autonomy, traffic density, routes, and other traffic elements. Similarly, software that specializes in vehicle dynamics, physical limitations, and vehicle control has been used to closely simulate realistic autonomous vehicle behavior under such scenarios. Different simulation tools for realistic autonomous vehicle simulation and traffic simulation have been merged together in this paper, creating a realistic simulator with Hardware-in-the-Loop (HiL), Traffic-in-the-Loop (TiL), and Software in-the-Loop (SiL) simulation capabilities.