Search Results

Heavy Duty Vehicle (HDV) Diesel emission regulations are set to be tightened in the future. The introduction of PN PEMS testing for Euro VI-e, and the expected tightening of PM/NOx targets set to be introduced by CARB in the US beyond 2024 are expected to create challenging tailpipe PN conditions for OEMs. Additionally, warranty and the useful life period will be extended from current levels. Improved fuel efficiency (reduction of CO2) also remains an important performance criteria. Furthermore, future non-road diesel emission regulations may follow tighten HDV diesel emission regulations contents, and non-road cycles evaluation needs to be considered as well for future. In response to the above tightened regulation, for Diesel Particulate Filter (DPF) technologies will require higher PN filtration performance, lower pressure drop, higher ash capacity and better pressure drop hysteresis for improved soot detectability.

An exhaust heat recovery (EHR) system is an effective and attractive means of improving fuel economy and in-vehicle comfort, especially of hybrid cars in winter. However, many conventional bypass systems, which have a bypass pipe and bypass valve with a thermal actuator, are still large and heavy, and it is necessary not only to effectively improve the heat recovery but also to minimize the size and weight of EHR systems. Sakuma et al. reported new-concept heat exchangers and EHR systems using a highly heat-conductive SiC honeycomb, including a non-bypass system. However, since this non-bypass system always recovers heat from the exhaust gas, its heat recovery performance was set so as not to exceed the cooling capability of the radiator at a high engine load to prevent overheating of the vehicle.

Reducing the fuel consumption of powertrains in internal combustion engines is still a major objective from an environmental viewpoint. Internal combustion engines waste a huge part of the fuel energy as heat in the exhaust line. Currently, exhaust heat recovery (EHR) systems are attracting attention as an effective means of reducing fuel consumption by collecting heat from waste exhaust gas and using it for rapid warming up of the engine and cabin heating [1, 2, 3, 4]. The benefits of the EHR system are affected by a trade-off between the efficacy of the recovered useful thermal energy and the adverse effect of the additional weight (heat mass) of the system [5]. Conventional EHR systems have a complex heat exchanger structure and a structure in which a bypass pipe and heat exchanger are connected in parallel, giving them a large size and heavy weight. We have developed a new-concept silicon carbide (SiC) heat exchanger with a dense SiC honeycomb.

To meet stringent emissions regulations, high conversion efficiency is required. This calls for advanced catalyst substrates with thinner walls and higher cell density. Higher cell density is needed because it brings higher mass transfer from the gas to the substrate wall. Basically, the increase in total surface area (TSA) causes higher mass transfer. However, not only the TSA, but the cell shape also has a great effect on mass transfer. There are two main kinds of substrates. One is the extruded ceramic substrate and the other is the metal foil type substrate. These have different cell shapes due to different manufacturing processes. For the extruded ceramic substrate, it is possible to fabricate various cell shapes such as triangle, hexagon, etc. as well as the square shape. The difference in the cell shape changes not only the mass transfer rate, but also causes pressure loss change. This is an important item to be considered in the substrate design.

DPF substrate is exposed to high temperature during regeneration and to acid components in exhaust gas. Therefore, DPF material needs to have an excellent thermal shock resistance, thermal and chemical stability to the sulfuric acid. This paper presents the durability test results of the Si-SiC DPF material. In particular, thermal shock resistance, oxidation resistance and acid resistance parameters have been evaluated by comparison with recrystallized-SiC and cordierite materials. As the results, the strength of Si-SiC decreased between ΔT=500 and 600deg.C, while that of recrystallized-SiC decreased between ΔT=300 and 400deg.C. The result is attributed to the difference in the elastic modulus. About oxidation resistance, material properties of Si-SiC, compared between pre- and post- oxidation, have greater stability than those of recrystallized SiC. And naturally, both SiC materials have superior acid resistance to cordierite.

The future emission limits for gasoline fuelled passenger cars require more and more efficient exhaust gas aftertreatment devices - the catalytic converter being one essential part of the complex system design. The present paper summarizes the results of several basic research programs putting major emphasis on the application of highly sophisticated three-way catalyst technologies being taylored for the utilization on ultra thin-wall ceramic substrates. In the first part of the investigation the following effects were examined in detail: Different washcoat loadings at constant PGM-loadings Different volumes of catalysts for constant amounts of PGM and washcoat Similar washcoat technologies at different ratios of WC-loading to precious metal concentration in the washcoat.

A computational model which describes the combustion and heat transfer that takes place during forced regeneration of honeycomb structured wall flow type diesel particulate filter was developed. In this model, heat released by the soot- oxygen reaction, convection heat transfer in the gas phase, conductive heat transfer in solid walls, and heat transfer between the gas and wall of each honeycomb cell at various radial positions in a filter are calculated. Each honeycomb cell was modeled as one solid phase and two gas phases and these three phases were divided in the axial direction into small elements. Conductive heat transfer between the small solid elements and convection heat transfer between the small gas elements were calculated for each small time increment. Conductive radial heat transfer between honeycomb cells was also calculated.

This paper describes a newly-developed, high-performance RTD,(Resistive Temperature detector), which meets OBD-II monitoring requirements. The OBD-II catalyst monitoring requirements are high temperature durability, high accuracy, and narrow piece-to-piece variation. Catalyst monitoring methods have been reviewed and studied by checking the catalyst exotherm(1)(2). The preliminary test results of catalyst monitoring are also described herein.

This paper describes the design concept and evaluation test results of a multi-layered, thick film zirconia NOx sensor which can be used for lean-burn engine management. The oxygen concentration in the measuring gas is lowered to a predetermined level with an oxygen pumping cell, in the first stage. In the second stage, another pumping cell further lowers the oxygen concentration which results in simultaneous NOx decomposition. The second stage pumping current is proportional to the NOx concentration in the measuring gas.

Ceramic honeycomb wall flow diesel particulate filters (DPF) have been investigated for use in exhaust gas control of diesel vehicles. However, before they can be used, prevention of thermal shock failure during combustion regeneration is necessary. Studies were conducted on thermal shock failures on 9-inch diameter large volume DPF during regeneration by finite element analyses (FEA). These studies reveal that, within safe limits, maximum thermal stress is almost constant even at different gas flow rates and oxygen concentrations. Regeneration tests were also conducted on large volume DPF of several materials having different pore size distributions. FEA thermal stress was compared with mechanical strength of the material at safe levels.

Ceramic honeycombs have been used as automotive catalyst supports in US, Japan, Europe and other highly urbanized countries. Now, engine output is a great concern for automanufacturers, and reduction of the wall thickness of honeycomb substrates became indespensable for maintenance of gas flow restriction to a certain low level. To reduce wall thickness, material should be strong to maintain canning strength of substrates. Mechanical strength was improved with high density cordierite. However, isostatic strength of whole substrates was still insufficient with reduced thin walls for canning in spite of the material's high mecanical strength. Discussion is carried out on further possibility of improving canning performance of thin wall substrates as well as flow restriction, and warm up characteristics.

The high-temperature durability of 85 mm tip diameter silicon nitride ceramic radial turbine rotors was evaluated with a hot gas spin test rig. The rotors withstood up to a turbine tip speed of 700 m/s at TIT of 1300°C under partially loaded conditions and 570 m/s at TIT of 1300°C under fully loaded conditions, respectively. The material of the rotors was a post-HIPed silicon nitride. The basic fatigue properties of the material were measured at high temperatures. In the hot gas spin test, the temperature and stress distributions at the turbine blade were calculated with a finite element method. The results of the hot-gas spin test are discussed by means of a failure prediction analysis on the basis of the Weibull statistics.

The effect on engine performance of insulating combustion chambers was simulated for a turbocharged direct injection diesel engine. We developed a low heat rejection (LHR) diesel cycle simulation. It includes a gas flow model, a heat transfer model, and a two zone combustion model. In the heat transfer model, convective and radiation heat transfer between the gas and walls was computed, taking into account the combustion chamber surface temperature swings. In the combustion model's combustion zone, the temperature and the chemical equilibrium compositions were determined. They were used to calculate the NO formation rate by assuming a modified Zeldvich mechanism. The combustion zone temperature was also used to estimate the radiation heat transfer. Simulations were performed of various combustion chamber surface materials and various LHR levels. The factors which affect thermal efficiency and exhaust emissions were deduced and their influences discussed.

This paper describes the design and property of an electrically heated zirconia exhaust gas oxygen sensor having small-sized and sheet-shaped sensing element. Sensing element and sensor have been miniaturized by monolithic formation of sensing element and heater by means of thick-film techniques. The difference in response property according to the angle of the electrode to exhaust gas flow because of the sheet-shaped configuration of sensing element was minimized by proper design of protective cover. Similarity in λ control property and limit cycle frequency was demonstrated with heated zirconia oxygen sensor having test tube-shaped sensing element by engine dynamometer durability test over 120,000 equivalent miles.