Search Results

Chest injuries occur frequently in frontal collisions. During impact, tension in the lap belt is transferred to the inboard shoulder belt, which compresses the lower ribs of the occupant. In this research, inboard shoulder belt and lap belt geometries and forces were investigated to reduce chest deflection. First, the inboard shoulder belt geometry was changed by the lap/shoulder belt (L/S) junction for the rear seat occupant in sled tests using Hybrid III finite element simulation, sled tests and THOR simulation. As the L/S junction was closer to the ASIS (anterior superior iliac spine), chest deflection of the Hybrid III was smaller. The L/S junction around the ilium has the potential to reduce chest deflection without significant increase of head excursion. For THOR, although the chest deflection reduction effect due to closer L/S junction to the ASIS was observed, chest deflection was still substantially large since the lap belt overrode the ASIS.

The purpose of this study is to clarify the mechanism of traffic accidents involving cyclists. The focus is on the characteristics of cyclist accidents and scenarios, because the number of traffic accidents involving cyclists in Tokyo is the highest in Japan. First, dangerous situations in traffic incidents were investigated by collecting data from 304 cyclists in one city in Tokyo using a questionnaire survey. The survey indicated that cyclists used their bicycles generally while commuting to work or school in the morning. Second, the study investigated the characteristics of 250 accident situations involving cyclists that happened in the city using real-world bicycle accident data. The results revealed that the traffic accidents occurred at intersections of local streets, where cyclists collided most often with vehicles during commute time in the morning. Third, cyclists’ behavior was observed at a local street intersection in the morning in the city using video pictures.

In the conventional approval test method of fuel consumption for heavy-duty diesel vehicles currently in use in Japan, the fuel consumption under the transient test cycle is calculated by integrating the instantaneous fuel consumption rate referred from a look-up table of fuel consumptions measured under the steady state conditions of the engine. Therefore, the transient engine performance is not considered in this conventional method. In this study, a highly accurate test method for fuel consumption in which the map-based fuel consumption rate is corrected using the transient characteristics of individual engines was developed. The method and its applicability for a heavy-duty diesel engine that complied with the Japanese 2009 emission regulation were validated.

Degradation of the deNOx performance has been found in in-use heavy-duty vehicles with a urea-SCR system in Japan. The causes of the degradation were studied, and two major reasons are suggested here: HC poisoning and deactivation of pre-oxidation catalysts. Hydrocarbons that accumulated on the catalysts inhibited the catalysis. Although they were easily removed by a simple heat treatment, the treatment could only partially recover the original catalytic performance for the deNOx reaction. The unrecovered catalytic activity was found to result from the decrease in conversion of NO to NO2 on the pre-oxidation catalyst. The pre-oxidation catalyst was thus studied in detail by various techniques to reveal the causes of the degradation: Exhaust emission tests for in-use vehicles, effect of heat treatment on the urea-SCR systems, structural changes and chemical changes in active components during the deactivation were systematically investigated.

In side collision accidents, the head is the most frequently injured body region for child occupants seated in a child restraint system (CRS). Accident analyses show that a child's head can move out of the CRS shell, make hard contact with the vehicle interior, and thus sustain serious injuries. In order to improve child head protection in side collisions, it is necessary to understand the injury mechanism of a child in the CRS whose head makes contact with the vehicle interior. In this research, an SUV-to-car oblique side crash test was conducted to reconstruct such head contacts. A Q3s child dummy was seated in a CRS in the rear seat of the target car. The Q3s child dummy's head moved out beyond the CRS side wing, moved laterally, and made contact with the side window glass and the doorsill. It was demonstrated that the hard head contact, which produced a high HIC value, could occur in side collisions.

The number of traffic deaths in Japan was 4,863 in 2010. Pedestrians account for the highest number (1,714, 35%), and vehicle occupants the second highest (1,602, 33%). Pedestrian protection is a key countermeasure to reduce casualties in traffic accidents. A striking vehicle's impact velocity could be considered a parameter influencing the severity of injury and possibility of death in pedestrian crashes. A collision damage mitigation braking system (CDMBS) using a sensor to detect pedestrians could be effective for reducing the vehicle/pedestrian impact velocity. Currently in Japan, cars equipped with the CDMBS also have vision sensors such as a stereo camera for pedestrian detection. However, the ability of vision sensors in production cars to properly detect pedestrians has not yet been established. The effect of reducing impact velocity on the pedestrian injury risk has also not been determined.

Study of DME diesel engines was conducted to improve fuel consumption and emissions of its. Additionally, DME trucks were built for the promotion and the road tests of these trucks were executed on EFV21 project. In this paper, results of diesel engine tests and DME truck driving tests are presented. As for DME diesel engines, the performance of a DME turbocharged diesel engine with LPL-EGR was evaluated and the influence of the compression ratio was also explored. As for DME trucks, a 100,000km road test was conducted on a DME light duty truck. After the road test, the engine was disassembled for investigation. Furthermore, two DME medium duty trucks have been developed and are now the undergoing practical road testing in each area of two transportation companies in Japan.

The use of biofuel is essential for the reduction of greenhouse gas emission. This paper highlights the use of biodiesel as a means of reducing greenhouse gas emission from the diesel engine of heavy-duty vehicles. Biodiesel is fatty acid methyl ester (FAME) obtained through ester exchange reaction by adding methanol to oil, such as rapeseed oil, soybean oil, palm oil, etc. The CO₂ emission from combustion of biodiesel is defined to be equivalent to the CO₂ volume absorbed by its raw materials or plants in their course of growth. On the other hand, however, biodiesel is known to increase the NOx emission when compared with operating with conventional diesel fuel, then suppressing this increase is regarded as a critical issue. This study is intended to identify the fuel properties of biodiesel free from increase in the NOx emission.

The number of traffic deaths in Japan was 4,914 in 2009. Since the head was the most common site of injury in traffic accidents (2,302, 47%), traumatic brain injury causes the fatalities in these accidents. The aim of the present study was to quantify micro injuries in the animal brain for gaining insight and understanding of the human brain injury tolerance. Using porcine brain matter, in vitro stress relaxation experiments and in vivo impact experiments were conducted. In both experiments, the distribution of the damage ratio of the transverse to longitudinal length of cells, hereafter, referred to as an aspect ratio, in the brain matter under loading was examined. In the in vitro stress relaxation experiments, specimens were compressed vertically with a compression velocity of 1 mm/s, and the displacement was held for 140 sec when the compression strain reached the target strain. In the experiments, there were five categories of compression strain: 10, 20, 30, 40, and 50 percent.

The emission reduction from diesel engines is one of major issues in heavy duty diesel engines. Super Clean Diesel (SCD) Engine for heavy-duty trucks has also been researched and developed since 2002. The main specifications of the SCD Engine are six cylinders in-line and 10.5 l with a turbo-intercooled and cooled EGR system. The common rail system, of which the maximum injection pressure is 200 MPa, is adopted. The turbocharger is capable of increasing boost pressure up to 501.3 kPa. The EGR system consists of both a high-pressure loop (HP) EGR system and a low-pressure loop (LP) EGR system. The combination of these EGR systems reduces NOx and PM emissions effectively in both steady-state and transient conditions. The emissions of the SCD Engine reach NOx=0.2 g/kWh and PM=0.01 g/kWh with aftertreatment system. The adopted aftertreatment system includes a Lean NOx Trap (LNT) and Diesel Particulate Filter (DPF).

Repeatabilities of PM measurements on a heavy-duty diesel engine equipped with a diesel particulate filter (DPF) using a filter weighing method and a number counting method with a full flow dilution system and a partial flow system were evaluated. The filter method with partial flow exhibited the best repeatability. However, a good correlation between the full flow and the partial flow number counting results suggests that the fluctuations observed using the number counting method were caused by changes in the engine exhaust. Applying a strict preconditioning procedure should improve the repeatability of the number counting method because this method is more sensitive than the filter weighing method. In addition, the effects of the specifications for the number counting method were evaluated. The results indicate that the hose length from the tip of the sampling probe to the inlet of the number counting system had a negligible effect.

The use of biodiesel fuels as an alternative fuel for petroleum diesel fuel is very effective for the reduction of CO2 emission, because biodiesel is produced from renewable biomass resources. Biodiesel is usually blended to conventional diesel fuel in various proportions. It is possible that this biodiesel blending causes the problems on emission characteristics of modern diesel engine, because it could be confirmed that the application of neat biodiesel to modern diesel engines whose control parameters were optimized for conventional diesel fuel deteriorated the emission performances. It is necessary to clarify the effect of biodiesel blending on exhaust emissions of modern diesel engine. Rapeseed oil methyl ester (RME) was selected as a biodiesel used in this study.

BAS assists driver's by automatically increasing their braking power during an emergency brake event when the driver is unable to apply a sufficient brake force.. There are two performance requirements that BAS must fulfill in order to be employed effectively. One is the ability to activate when the driver suddenly applies brakes in an emergency while the other is the ability to provide additional assistance. Further study of BAS activation timing and degree of assistance in relation to driver acceptance is needed. The driver's acceptance of BAS refers to the BAS activation only during an emergency. A study was conducted to clarify drivers' emergency braking characteristics and measure the frequency of BAS activation during normal braking. One aim of the study was to verify driver characteristics during emergency braking on a test course.

Application of biodiesel fuel (BDF) to diesel engine is very effective to reduce CO2 emission, because bio-diesel is carbon neutral in principle. However, when biodiesel was applied to conventional diesel engines without modification for biodiesel, NOx emission was increased by the change in fuel characteristics. It is necessary to introduce some strategies into diesel engines fuelled with biodiesel for lower NOx emission than conventional diesel fuel case. The purpose of this study is to reveal that exhaust gas recirculation (EGR) is one of the solutions for the reduction of NOx emission and meeting the future emission regulations when using biodiesel. Neat Rapeseed oil methyl ester (RME) as a biodiesel (B100) was applied to diesel engines equipped with high pressure loop (HPL) EGR system and low pressure loop (LPL) EGR system. Cooled HPL EGR was increased during steady-state operations and JE05 transient mode tests.

Head-up displays (HUDs) require drivers to perceive double images simultaneously, that is, the scene to the front and display images, and this simultaneous viewing of two objects may cause cognitive confusion during driving. In this paper, we discuss some factors that determine the appropriate area for HUDs. First we discuss the feeling of troublesomeness with consideration of eye movements during driving. Secondly, we investigated the situation wherein the driver in a trailing vehicle perceives the stop lamps of a lead vehicle. Upon these considerations, we conclude that in the vertical direction the area under 4 degrees below the horizontal line would be a safer display area.

The chemical mechanism responsible for controlling ignition timing by using additives in HCCI has been investigated. Dimethyl ether (DME) and methanol were used as the main fuel and the additive, respectively. Fuel consumption and intermediate formation in the first stage (cool ignition) were measured with crank angle resolved pulse-valve sampling and exhaust gas analysis, where HCHO, HCOOH, CO, H2O2 and other species were detected as the intermediate. The effect of methanol addition retarding ignition is represented by an analytical model in which the growth rate of the chain reaction is reduced by the methanol addition.

The object of this study is to investigate an on-board diagnostic method to detect the deterioration of a three-way catalyst (TWC) under actual vehicle operating conditions, including the acceleration state. The signal data of two oxygen sensors were processed by the fast Fourier transformation (FFT) method. As a result, we found that the power spectrum of the signal waves can be the index of catalyst deterioration degree. Furthermore, it was confirmed that the difference between the power spectrum of the upstream oxygen sensor signal and one of the downstream oxygen sensor signal named ΔPower is effective index for detection of deteriorated catalyst under acceleration conditions.

Application of biodiesel fuel (BDF) to diesel engine is very effective to reduce CO2 emission, because biodiesel is carbon neutral in principle. However, biodiesels yield an increase in NOx emission from conventional diesel engine, compared with diesel fuel case. Therefore, some strategies are needed for meeting the future emission regulations when using biodiesel. In this study, rapeseed oil methyl ester (RME) was applied to diesel engine equipped with exhaust gas recirculation (EGR) system and NOx storage reduction (NSR) catalyst. NOx reduction rate of NSR catalyst was drastically decreased by using RME, even if injection quantity of RME for rich spike was enhanced. However, an increase in EGR rate could reduce NOx emission without the deterioration in smoke and PM emissions.

A prototype CNG engine for heavy-duty trucks has been developed. The engine had sufficient output in practical use, and the green-house gas emission rate was below that of the base diesel engine. Furthermore, the NOx emission rate was reduced to 0.16 g/kWh in the JE05 mode as results of having fully adjusted air fuel ratio control. The measured emission characteristics of particles from the prototype CNG engine demonstrated that oil consumption was related to the number of particles. Moreover, when oil consumption is at an appropriate level, the accumulation mode particles are significantly reduced, and the nuclei mode particles are fewer than those of diesel-fueled engines.

The 1997 Kyoto protocol came into effect in February, 2005 to reduce greenhouse gases within the period 2008-2012 by at least 5 % with respect to 1990 levels. Application of biodiesel fuel (BDF) to diesel engine is very effective to reduce CO2 emission, because BDF is carbon neutral in principle. The purpose of this project is to produce a light-duty biodiesel truck which can be suitable for emission regulation in next generation. The effect of BDF on the performance and emissions of modern diesel engine which was equipped with the aftertreatment for PM and NOx emissions was investigated without modifications of engine components and parameters, as a first step for research and development of biodiesel engine. Rapeseed oil methyl ester (RME) was selected in behalf of BDF, and combustion characteristics, engine performance and exhaust emissions were made a comparison between RME and petroleum diesel fuel by steady operation and Japan transient mode (JE05) tests.