Search Results

Hydrogen has attracted attention as one of the key fuels for making internal combustion engines carbon neutral. However, the combustion characteristics of hydrogen differ greatly from those of conventionally used hydrocarbons. Therefore, in order to develop next-generation internal combustion engines that operate on hydrogen, it is first necessary to have a thorough understanding of the combustion characteristics of hydrogen. Engines that can take maximum advantage of those characteristics should be developed on the basis of that knowledge. Toward that end, the purpose of this study was to investigate the fundamental combustion characteristics of hydrogen in a test engine. This paper presents the results of an investigation of the effects on low-temperature oxidation reactions and autoignition when hydrogen was blended into dimethyl ether (DME) [1, 2], a gaseous hydrocarbon fuel.

Liquid fuel attached to the wall surface of the intake port, the piston and the combustion chamber is one of the main causes of the unburned hydrocarbon emissions from a port fueled SI engine, especially during transient operations. To investigate the liquid fuel film formation process and fuel film behavior during transient operation is essential to reduce exhaust emissions in real driving operations, including cold start operations. Optical techniques have been often applied to measure the fuel film in conventional reports, however, it is difficult to apply those previous techniques to actual engines during transient operations. In this study, using MEMS technique, a novel capacitance sensor has been developed to detect liquid fuel film formation and evaporation processes in actual engines. A resistance temperature detector (RTD) was also constructed on the MEMS sensor with the capacitance sensor to measure the sensor surface temperature.

This study focused on a lean-burn regime using a pre-chamber for improving the efficiency of internal combustion engines. Combustion images were visualized using a two-stroke, single-cylinder, optically accessible engine fitted with a cylindrical pre-chamber. The L/D ratio of the pre-chamber length (L) to its diameter (D) and the diameter of the pre-chamber orifice were varied as parameters. Combustion characteristics were analyzed based on the visualized jet flow configuration and combustion chamber pressure measurements. The results revealed that the combustion duration tended to be longer with a smaller L/D ratio and that the coefficient of variation (COV) of the indicated mean effective pressure (IMEP) was smaller and more stable. With a smaller orifice diameter, the jet velocity was faster, and the flame development duration was shorter, but the combustion duration was longer; IMEP tended to be lower, but the COV of IMEP was smaller.

Although methane number is widely used to predict knocking occurrence and its intensity, it does not determine a fuel composition uniquely, that means, the knocking intensity by the different composition fuel must show difference even if the same methane number fuels are employed. To establish a novel index, the knocking intensity and the autoignitive propagation velocity, as consequence of spontaneous ignition process, are investigated both experimentally and numerically by using the different composition gaseous fuels with same methane number. Methane/ethane/air and methane/n-butane/air mixtures with the same methane number of 70 and the equivalence ratio of 0.5 were employed. They are rapidly compressed and ignited spontaneously by a Rapid Compression Machine. Ignition delay times, autoignitive propagation velocities, and knocking intensity were measured by acquired pressure histories and high-speed imaging.

This study aimed to achieve both a high compression ratio and low knock intensity in a two-stroke engine. Previous research has suggested that knock intensity can be reduced by combining combustion chamber geometry and scavenging passaging design for the same engine specifications with a compression ratio of 13.7. In this report, we investigate whether low knock intensity can be achieved at compression ratios of 14.4 and 16.8 by adjusting the combustion chamber geometry and scavenging passage design. As a result, the mechanism by which combustion chamber geometry and scavenging passage design change knock intensity was clarified.

Knocking is an important issue in improving the efficiency of spark ignition engines. It can be detected by photographing with high-speed cameras or measuring in-cylinder pressure or engine vibration or engine radiation sound. However, these methods each have the problems for example sensor damage risk or necessity of machining the engine. In this paper, we propose the efficient measurement method and the effective evaluation method with the restricted measurement results for engine knocking detection by utilizing the simultaneous measurement results of knocking with these sensors.

In internal combustion engine development, the ongoing research can be mainly classified into two categories based on the purpose: limiting exhaust emissions and searching for alternative fuels. One of the effective approaches reduce emissions is the improvement of thermal efficiency. Certain types of alternative fuels derived from renewable resources were estimated to confirm the thermal efficiency. This study uses a single-cylinder engine added with olefin and oxygenated additive fuel, such as 1-hexene, ethanol, and ETBE, to evaluate the parameters that affect thermal efficiency. Furthermore, the effects of various additive fuels are summarized and essential information is provided for determining next- generation fuel composition.

The influence of ethanol volume fraction on the spontaneous ignition of homogeneous premixed gas reformed by non-equilibrium plasma was investigated. The HCCI experiments of the gas was carried out using a Rapid Compression Machine (RCM). The spontaneous ignition process and reforming process were numerically investigated by reaction simulation in OD. A simplified model was proposed to explain the influence of the reforming of the gas with different ethanol volume fractions, and the model was validated. These results indicate that the influence of the reforming on ignition delay of cool flame is almost irrespective of the ethanol volume fractions.

Lean combustion has been well known to be an effective method to improve the thermal efficiency. However, leaner mixture is prone to cause the unstable combustion and poorer unburned hydrocarbon (UTHC) emissions. Pre-chamber turbulent jet combustion has been proved to enhance the combustion stability under ultra-lean conditions. However, more NOx is formed during the combustion, resulting in the fact that the tailpipe NOx emission is too high to be still not available for the real application. In this report, in order to achieve a higher air excess ratio while keeping lower UTHC emissions, and especially NOx emission, a new combustion technique which combined pre-chamber jet combustion with fuel reforming was proposed and experimentally demonstrated on a pre-chamber engine.

Homogeneous charge compression ignition (HCCI) combustion is promising for not only high thermal efficiency but also reducing nitrogen oxides (NOx) and PM simultaneously. However, the operational range of the HCCI combustion is limited because of some issues, such as poor control of ignition timing and knocking by the excessive rate of pressure rise. In this study, a new combustion system based on the HCCI combustion process is proposed based on the authors' previous experimental work. This combustion system has a divided combustion chamber of two parts, one is small and the other is large. The most significant feature is the small chamber inside the piston. At first, combustion takes place in the small chamber, and then the burned gas is ejected into the large chamber to ignite the mixture in the large chamber.

Post-oxidation has been used to enhance the chemical reactions in the exhaust gas pipes, leading to the activations of the turbocharger and catalyst at cold state. In this research, a detailed study of the various mechanisms for post-oxidation is performed. For the post-oxidation activation, the unburned gas species (CO, THC, H2) in the exhaust manifold must be produced by some methodologies, such as scavenging, lambda-split, and post-injection. The required amount of O2 concentration can be either supplied by the scavenging (valve overlap tuning) or the secondary air injection (SAI) system. Mixing the species is also an important key to promoting post- oxidation, and an internal bypass adapter with a modified exhaust adapter shape was developed and evaluated.

Following Part 1 of the previous study, this paper reports the structure’s exciting force and summarize the overall research results. An experimental study was conducted to clarify the relationship between engine combustion and vibration, and to establish technology to suppress it. This study focused on the vehicle interior noise caused by combustion in which vibration transmission is the main component at high speed and high load region. A phenomenon in which both the combustion’s exciting force and the structure’s exciting force are combined is defined as vehicle interior noise caused by combustion. Conventionally, combustion and vibration are often discussed in terms of the average cycle, but considering the nonstationary property of vibration, in this paper analyzed the structure’s exciting force characteristics for vibration in cycle-by-cycle. Analysis was conducted using the combustion indicators clarified in the previous study.

This study focused on the vehicle interior noise caused by combustion in which vibration transmission is the main component at high speed and high load region. A phenomenon in which both the combustion’s exciting force and the structure’s exciting force are combined is defined as vehicle interior noise caused by combustion. Conventionally, combustion and vibration are often discussed in terms of the average cycle, but considering the nonstationary property of vibration, in this paper analyzed the combustion characteristics for cycle-by-cycle and investigated indicators for the combustion’s exciting force. The engine vibration is affected by heat release characteristics even with the same engine structure specifications. The heat release characteristics were determined as indicators for the combustion’s exciting force. Transfer Path Analysis (TPA) revealed that there is piston transmission in the target frequency band.

Some SI (spark-ignition) engines fueled with gasoline for industrial machineries are designed based on the conventional diesel engine in consideration of the compatibility with installation. Such diesel engine-based SI engines secure a combustion chamber by a piston bowl instead of a pent-roof combustion chamber widely applied for SI engines for automobiles. In the development of SI engines, because knocking deteriorates the power output and the thermal efficiency, it is essential to clarify causes of knocking and predict knocking events. However, there has been little research on knocking in diesel engine-based SI engines. The purpose of this study is to elucidate knocking phenomena in a gasoline engine with a re-entrant piston bowl and swirl flow numerically and experimentally. In-cylinder visualization and pressure analysis of knock onset cycles have been experimentally performed. Locations of autoignition have been predicted by 3D-CFD analysis with detailed chemical reactions.

In recent years, the improvement in the fuel efficiency and reduction in CO2 emission from internal combustion engines has been an urgent issue. The lean burn technology is one of the key technologies to improve thermal efficiency of SI engines. However, combustion stability deteriorates at lean burn operations. The reduction in cycle-to-cycle and cylinder-to-cylinder variations is one of the major issues to adapt the lean burn technique for production engines. However, the details of the causes and mechanisms for the combustion variations under the lean burn operations have not been cleared yet. The purpose of this study is to control cylinder to cylinder combustion variation. A conventional turbocharged direct injection SI engine was used as the test engine to investigate the effect of engine control parameters on the cylinder to cylinder variations. The engine speed is set at 2200 rpm and the intake pressure is set at 58, 78, 98 kPa respectively.

A small 2-stroke engine can be an effective power source for an electric generator mounted on a series hybrid electric vehicle. In recent years, a technology referred to as pre-chamber jet combustion has attracted attention as a means of enhancing thermal efficiency by improving mixture ignitability. In this study, experiments were conducted to investigate differences in combustion behavior between the application of spark-ignited (SI) combustion and pre-chamber jet combustion to a small, two-stroke engine. The experimental equipment used was a two-stroke, single-cylinder, optically accessible engine with a displacement of 63.3 cm3. Differences between conventional SI combustion and pre-chamber jet combustion were examined by means of in-cylinder pressure analysis, in-cylinder combustion visualization and image processing software. The diameter of the connecting orifice of the pre-chamber was varied between two types.

A fuel reforming technology using a low temperature oxidation was developed to improve a NOx reduction performance of HC-SCR (Hydrocarbons Selective Catalytic Reduction) system, which does not require urea. The low-temperature oxidization of a diesel fuel in gas phase produces NOx reduction agents with high NOx reduction ability such as aldehydes and ketones. A pre-evaporation-premixing-type reformer was adopted in order to generate a uniform temperature field and a uniform fuel/air premixed gas, and to promote the low temperature oxidation efficiently. As a fundamental study, elementary reaction analysis for n-hexadecane/air premixtures was carried out to investigate the suitable reformer temperature and fuel/air equivalence ratio for generation of oxygenated hydrocarbons. It was found that the reforming efficiency was highest at the reforming temperature around 623 to 673K, and aldehydes and ketones were produced.

LSPI (Low speed pre-ignition) is a serious issue in highly boosted gasoline engines. The causes have been studied and lube oil affects the onset. In order to examine the effect of lubricating oil consumption on super knock caused by pre-ignition, measurements of in-cylinder pressure, temperature, oil consumption by sulfur trace at steady and transient conditions were conducted. Also, new piston ring pack was applied to reduce both of blow-by gas and oil consumption. As a result, accumulated oil during deceleration was found to cause pre-ignition after acceleration. The pre-ignition frequency is much higher than in steady condition, however, the amount of oil does not directly affect pre-ignition frequency, but dilution of oil and evaporation of oil/fuel and other parameters, such as temperature, pressure, and oil additives determine pre-ignition onset. In order to see the mechanism of pre-ignition onset, numerical simulations were conducted.

To increase thermal efficiency of internal combustion engines, dilution combustion systems, such as lean burn and exhaust gas recirculation systems, have been developed. These systems require spark-ignition coils generating large discharge current and discharge energy to achieve stable ignition under diluted mixture conditions. Several studies have clarified that larger discharge current increases spark-channel stretch and decreases the possibility of spark channel blow-off and misfire. However, these investigations do not mention the effect of larger discharge current and energy on the initial combustion period. The purpose of this study was to investigate the relation among dilution ratio, initial-combustion period, and coil specifications to clarify the control factor of the dilution limit.

In this research, simulation and experimental investigation of H2 emission formation and its influence during the post-oxidation phenomenon were conducted on a turbo-charged spark ignition engine. During the post-oxidation phenomenon phase, rich air-fuel ratio (A/F) is used inside the cylinder. This rich excursion gives rise to the production of H2 emission by various reactions inside the cylinder. It is expected that the generation of this H2 emission can play a key role in the actuation of the post-oxidation and its reaction rate if enough temperature and mixing strength are attained. It is predicted that when rich combustion inside the cylinder will take place, more carbon monoxide (CO)/ Total Hydro Carbon (THC)/ Hydrogen (H2) contents will arrive in the exhaust manifold. This H2 content facilitates in the production of OH radical which contributes to the post-oxidation reaction and in-turn can aid towards increasing the enthalpy.