Search Results

During this decade, the constant increase and globalization of passenger car sales has led countries to adopt a common language for the treatment of CO2 and other pollutant emissions. In this regard, the WLTC - World-wide harmonized Light duty Test Cycle - stands as the new global reference cycle for fuel consumption, CO2 and pollutant emissions across the globe. Regulations keep a constant pressure on CO2 emission reduction leading vehicle manufacturers and component suppliers to modify hardware to ensure compliance. Within this balance, lubricants remain worthwhile contributors to lowering CO2 emission and fuel consumption. Yet with WTLC, new additional lubricant designs are likely to be required to ensure optimized friction due to its new cycle operating conditions, associated powertrain hardware and worldwide product use.

The new lubricant was newly developed for differential gear unit to contribute to all friction factors/conditions (Boundary, Hydrodynamic & those Mixed Lubrication) even if the differential gear is operating under very severe conditions such as high-gear-contact pressure and highly sliding speed. The main concept of development was selecting and formulating the optimized additives for severe lubrication conditions in order to achieve the best balance between thinner-film thickness and extreme pressure performance. In conclusion, by the application of both synthetic base oil instead of mineral one and activation technology of MoDTC in spite of ZnDTP free formulation, it is finally realized to reduce the torque of final drive unit by 40% and it can be estimated the 0.5% of CO2 reduction in actual vehicles.

A new variable compression turbo (VC-Turbo) engine, which has a multi-link system for controlling the compression ratio from 8:1 to 14:1, requires high axial force for fastening the multi-links because of high input loads and the downsizing requirement. Therefore, it was necessary to develop a 1.6-GPa tensile strength bolt with plastic region tightening. One of the biggest technical concerns is delayed fracture. In this study, quenched and tempered alloy steels were chosen for the 1.6-GPa tensile strength bolt.

Wireless Power Transfer (WPT) promises automated and highly efficient charging of electric and plug-in-hybrid vehicles. As commercial development proceeds forward, the technical challenges of efficiency, interoperability, interference and safety are a primary focus for this industry. The SAE Vehicle Wireless Power and Alignment Taskforce published the Recommended Practice J2954 to help harmonize the first phase of high-power WPT technology development. SAE J2954 uses a performance-based approach to standardizing WPT by specifying ground and vehicle assembly coils to be used in a test stand (per Z-class) to validate performance, interoperability and safety. The main goal of this SAE J2954 bench testing campaign was to prove interoperability between WPT systems utilizing different coil magnetic topologies. This type of testing had not been done before on such a scale with real automaker and supplier systems.

There are strong demands for vehicle weight reductions so as to improve fuel economy. At the same time, it is also necessary to ensure crash safety. One effective measure for accomplishing such both requirements conflicting each other is to apply advanced high strength steel (AHSS) of 780 MPa grade or higher to the vehicle body. On the other hand, higher strength steels generally tend to display lower elongation causing formability deterioration. Nissan Motor Corporation have jointly developed with steel manufacturers a new 980 MPa grade AHSS with high formability with the aim of substituting it for the currently used 590 MPa grade high-tensile steel. Several application technologies have been developed through the verifications such as formability, resistance spot weldability, crashworthiness, and delayed fracture.

This paper presents the technologies incorporated in an electric vehicle (EV)/hybrid electric vehicle (HEV) inverter built with power semiconductors of silicon carbide (SiC) metal-oxide-semiconductor field-effect transistors (MOSFETs) instead of conventional silicon (Si) insulated gate bipolar transistors (IGBTs). A SiC inverter prototype of 2.9 L in size for driving an 80-kW motor was fabricated and evaluated on a motor test bench. The SiC inverter prototype attained average efficiency of 98.5% in the Worldwide harmonized Light-duty Test Cycle (WLTC) driving mode. The two main technologies achieved with this SiC inverter prototype are described. The first one is a new direct-cooled power module with a thick copper (Cu) heat spreader located under the semiconductors that improves thermal resistance by 34% compared with a conventional direct-cooled power module.

Mechanism of suddenly occurring behavior of low speed pre-ignition (LSPI) in boosted spark ignition (SI) engines was analyzed with various experimental methodologies. Endoscope-visualized 1st cycle of LSPI showed droplet-like luminous flame kernels as the origin of flame propagation before spark ignition. With the oil lubricated visualization engine, droplets flying were observed only after enough accumulation of fuel at piston crevice. Also, it was confirmed that subsequent cycles of LSPI occur only after enough operation time. These results indicated that local accumulation of liner adhered fuel and saturation of oil dilution can be a contributing factor to the sudden occurrence of LSPI.

The new Murano was developed with special emphasis on improving aerodynamics in order to achieve fuel economy superior to that of competitor models. This paper describes the measures developed to attain a drag coefficient (CD) that is overwhelmingly lower than that of other similar models. Special attention was paid to optimizing the rear end shape so as to minimize rear end drag, which contributes markedly to the CD of sport utility vehicles (SUVs). A lower grille shutter was adopted from the early stage of the development process. When open, the shutter allows sufficient inward airflow to ensure satisfactory engine cooling; when closed, the blocked airflow is actively directed upward over the body. The final rear end shape was tuned so as to obtain the maximum aerodynamic benefit from this airflow. In addition, a large front spoiler was adopted to suppress airflow toward the underbody as much as possible.

A suitable GF-5 engine oil formulation is investigated to improve the fuel economy of gasoline engines with hydrogen-free DLC-coated valve lifters. Molybdenum dithocarbamate (MoDTC) is shown to be a suitable friction modifier for low viscosity grade engine oils like 0W-20. A suitable Ca salicylate detergent is also determined from several types examined for maximizing the friction reduction effects of MoDTC. The most suitable Ca salicylate has a chemical structure capable of forming a borophosphate glass film on metal surfaces, which is known to improve the effects of MoDTC. A high viscosity index Group III base oil (VI>140) is also effective in improving fuel efficiency. It is further clarified that the structural design of the polymethacrylate viscosity modifier is another important factor in reducing engine friction.

An electric vehicle (EV) is promising as clean energy powered vehicle, due to increased interest in fuel economy and environment in recent years. However, it requires to meet unique safety performance such as electric safety. Nissan has developed a new electric vehicle which achieves electric safety in addition to maintaining enough cruising distance and cabin space. This was achieved by I he development of an all-new platform for electric vehicles. The electric safety was enhanced by the protection of high-voltage components based on consideration of component layout and body structure, high-voltage shutdown by impact sensing system and prevention of short circuit by fuse in the battery. As an example of the protection of high-voltage components, the battery which locates under the floor was protected by elaborative packaging and multi-layer protection structure.

At Nissan we have developed a new parallel hybrid system for rear-wheel-drive hybrid vehicles. As the main components of the hybrid system, both the motor and the inverter have been developed and are manufactured in house to attain high power density for providing responsive acceleration, a quiet EV drive mode and improved fuel economy. Because the motor is located between the engine and the transmission, it had to be shortened to be within the length allowed for the powertrain. Therefore, new technologies have been developed such as high-density, square-shaped windings and an optimized magnetic circuit specially designed for concentrated winding motors. The inverter is sized to a 12V battery, which it replaces in the engine compartment. Despite its compact size, the inverter must have rather large current capacity to drive a high-power motor. Heat management is critical to the design of a small but high-power inverter.

In 2006, Nissan began limited leasing of the X-TRAIL FCV equipped with their in-house developed Fuel Cell (FC) stack. Since then, the FC stack has been improved in durability, cold start-up capability, cost and size with the aim of promoting full-scale commercialization of FCVs. However, reduction of cost and size has remained a significant challenge because limited mass transport through the membrane electrode assembly (MEA) has made it difficult to increase the rated current density of the FC. Furthermore, it has been difficult to reduce the variety of FC stack components due to the complex stack configuration. In this study, improvements have been achieved mainly by adopting an advanced MEA to overcome these difficulties. First, the adoption of a new MEA and separators has improved mass transport through the MEA for increased rated current density. Second, an integrated molded frame (IMF) has been adopted as the MEA support.

In 2006, Nissan began limited leasing of the X-TRAIL FCV equipped with their in-house developed Fuel Cell (FC) stack. Since then, the FC stack has been improved in cost, size, durability and cold start-up capability with the aim of promoting full-scale commercialization of FCVs. However, reduction of cost and size has remained a significant challenge because limited mass transport through the membrane electrode assembly (MEA) has made it difficult to increase the rated current density of the FC. Furthermore, it has been difficult to reduce the variety of FC stack components due to the complex stack configuration. In this study, improvements have been achieved mainly by adopting an advanced MEA to overcome these difficulties. First, the adoption of a new MEA and separators has improved mass transport through the MEA for increased rated current density. Second, an integrated molded frame (IMF) has been adopted as the MEA support.

Evaluations of dummy injury readings obtained in regulatory crash tests and new car assessment program tests provide indices for the development of crash safety performance in the process of developing new vehicles. Based on these indices, vehicle body structures and occupant restraint systems are designed to meet the required occupant injury criteria. There are many types of regulatory tests and new car assessment program tests that are conducted to evaluate vehicle safety performance in side impacts. Factoring all of the multiple test configurations into the development of new vehicles requires advanced design capabilities based on a good understanding of the mechanisms producing dummy injury readings. In recent years, advances in computer-aided engineering (CAE) tools and computer processing power have made it possible to run simulations of occupant restraint systems such as side airbags and seatbelts.

This study concerns a dissimilar materials joining technique for aluminum (Al) alloys and steel for the purpose of reducing the vehicle body weight. The tough oxide layer on the Al alloy surface and the ability to control the Fe-Al intermetallic compound (IMC) thickness are issues that have so far complicated the joining of Al alloys and steel. Removing the oxide layer has required a high heat input, resulting in the formation of a thick Fe-Al IMC layer at the joint interface, making it impossible to obtain satisfactory joint strength. To avoid that problem, we propose a unique joining concept that removes the oxide layer at low temperature by using the eutectic reaction between Al in the Al alloy and zinc (Zn) in the coating on galvanized steel (GI) and galvannealed steel (GA). This makes it possible to form a thin, uniform Fe-Al IMC layer at the joint interface. Welded joints of dissimilar materials require anticorrosion performance against electrochemical corrosion.

This study examined methods of machining a microsurface texture on the surface of the rolling elements of a toroidal continuously variable transmission (CVT) for improving the traction coefficient. The microsurface texture of the toroidal surfaces consists of tiny circumferential grooves (referred to here as micro grooves) and a mirror-like surface finish similar to the rolling surface of bearings. Hard turning with a cubic boron nitride (cBN) cutting tool, grinding with a cBN wheel and micro forming were applied to machine the micro grooves. The results made clear the practical potential of each method. A micro forming device was also developed for use in actual production. A mirror-like surface finish and micro crowning of the convex portions of the microsurface texture were simultaneously executed by superfinishing them with a fine-grained elastic superfinishing stone.

This paper describes the methods adopted to improve the image quality of the all-around view system. This system uses multiple vehicle-mounted cameras to capture images of the circumstances around the vehicle. The images undergo viewpoint transformation and are synthesized to create a single image seen from a virtual perspective overhead. The specific methods discussed here concern optimization of the design parameters for the camera orientation and a camera calibration method that does not involve physical movement of the cameras.

Increasing expectations for stability at high speed call for the improvement of cars' aerodynamic performance, in particular lift reduction. However, due to styling constraints, traditional spoilers must be avoided and replaced by other solutions like underfloor components. Flow simulation is expected to be a useful tool for lift prediction, but the conventional models used so far did not represent complex geometry details such as the engine compartment and underfloor, and accuracy was insufficient. In the present study, a full vehicle simulation model, including the engine compartment and underfloor details, was used. Other improvements were also made such as optimization of the computational grid and the setting of boundary conditions for reproducing wind tunnel experiments or actual driving, making it possible to predict lift variations due to vehicle geometry changes.

In general, the improvement of vehicle body stiffness involves a trade-off with the body weight. The objective of this research is to derive the lightest-weight solution from the original vehicle model by finding the optimized spot-weld layout and body panel thickness, while keeping the body stiffness and number of spot welds constant. As the first step, a method of deriving the optimal layout of spot welds for maximizing body stiffness was developed by applying the topology optimization method. While this method is generally used in shape optimization of continuous solid structures, it was applied to discontinuous spot-weld positions in this work. As a result, the effect of the spot-weld layout on body stiffness was clarified. In the case of the body used for this research, body stiffness was improved by about 10% with respect to torsion and vertical and lateral bending.

This paper presents a new method for calculating optical flow using data from a high frame-rate camera. We focused on a feature of image data captured with a high frame-rate camera in which objects do not move more than one pixel between successive frames. This approach eliminates repetitive processing for object identification among frames taken at different sampling times. High-speed processing hardware architecture was designed with sequential processing only, and the algorithm was implemented in a field programmable gate array. The resultant unit can calculate optical flow for a 640×120 pixel size image with a 480-Hz processing cycle and 0.5-μsec processing latency.