Search Results

This paper describes a method for evaluating the equivalent temperature in vehicle cabins based on the new international standard ISO 14505-4, published in 2021. ISO 14505-4 defines two simulation methods to determine a thermal comfort index “equivalent temperature.” One method uses a numerical thermal manikin, and the other uses thermal factors to calculate. This study discusses the latter method to validate its accuracy, identify the key points to consider, and examine its advantages and disadvantages. First, the definition of equivalent temperature and the equation to calculate the equivalent temperature using thermal factors, such as air temperature, radiant temperature, solar radiation, and air velocity, are explained. In addition, the experiments and simulation methods are described.

In the previous paper (Part 1), measurements of equivalent temperature (teq) using a clothed thermal manikin and modeling of the clothed thermal manikin for teq simulation were discussed. In this paper (Part 2), the outline of the proposed mesh-free simulation method is described and comparisons between teq in the calculations and measurements under summer cooling with solar radiation and winter heating without solar radiation conditions in a vehicle cabin are discussed. The key factors for evaluating teq on each body segment of the clothed thermal manikin under cooling and heating conditions are also discussed. In the mesh-free simulation, even if there is a hole or an unnecessary shape on the CAD model, only a group of points whose density is controlled in the simulation area is generated without modifying the CAD model. Therefore, the fluid mesh required by conventional CFD code is not required, and the analysis load is significantly reduced.

Wireless Power Transfer (WPT) promises automated and highly efficient charging of electric and plug-in-hybrid vehicles. As commercial development proceeds forward, the technical challenges of efficiency, interoperability, interference and safety are a primary focus for this industry. The SAE Vehicle Wireless Power and Alignment Taskforce published the Recommended Practice J2954 to help harmonize the first phase of high-power WPT technology development. SAE J2954 uses a performance-based approach to standardizing WPT by specifying ground and vehicle assembly coils to be used in a test stand (per Z-class) to validate performance, interoperability and safety. The main goal of this SAE J2954 bench testing campaign was to prove interoperability between WPT systems utilizing different coil magnetic topologies. This type of testing had not been done before on such a scale with real automaker and supplier systems.

Electric Vehicles are very quiet at low speeds therefore people (especially the visually impaired) have difficulty recognizing that these vehicles are approaching. To address this concern, Approaching Vehicle Sound for Pedestrians system development has been discussed worldwide. In Japan, USA, Europe and China, government regulation is currently under study. As a solution to meet this concern, Nissan has developed the VSP (Approaching Vehicle Sound for Pedestrians) system for implementation on Nissan's first mass production Electric Vehicle. Nissan VSP emits a futuristic sound to satisfy 3 key stakeholders' concerns; for pedestrians to provide detectability, for drivers and neighborhoods to maintain a quiet environment. The sound emitted during forward motion has a “twin peaks and one dip” frequency signature, with modulation (or rhythmic structure) to accommodate human-beings ear frequency sensitivity, hearing loss due to aging and ambient noise conditions.

At Nissan we have developed a new parallel hybrid system for rear-wheel-drive hybrid vehicles. As the main components of the hybrid system, both the motor and the inverter have been developed and are manufactured in house to attain high power density for providing responsive acceleration, a quiet EV drive mode and improved fuel economy. Because the motor is located between the engine and the transmission, it had to be shortened to be within the length allowed for the powertrain. Therefore, new technologies have been developed such as high-density, square-shaped windings and an optimized magnetic circuit specially designed for concentrated winding motors. The inverter is sized to a 12V battery, which it replaces in the engine compartment. Despite its compact size, the inverter must have rather large current capacity to drive a high-power motor. Heat management is critical to the design of a small but high-power inverter.

Clarifying the impact of ETBE 8% blended fuel on current Japanese gasoline vehicles, under the Japan Clean Air Program II (JCAPII) we conducted exhaust emission tests, evaporative emission tests, durability tests on the exhaust after-treatment system, cold starting tests, and material immersion tests. ETBE 17% blended fuel was also investigated as a reference. The regulated exhaust emissions (CO, HC, and NOx) didn't increase with any increase of ETBE content in the fuel. In durability tests, no noticeable increase of exhaust emission after 40,000km was observed. In evaporative emissions tests, HSL (Hot Soak Loss) and DBL (Diurnal Breathing Loss) didn't increase. In cold starting tests, duration of cranking using ETBE 8% fuel was similar to that of ETBE 0%. In the material immersion tests, no influence of ETBE on these material properties was observed.

An investigation was made of the relationship between the driving speed at the time of impact and the injury levels suffered in accidents. The results showed that a 5 km/h or more reduction in collision speed tends to mitigate injury severity. Using sensors and brake actuators already in practical use, we have started to research a braking system aimed at reducing the collision speed by at least 5 km/h in rear-end collisions. The system estimates the risk of a collision with the vehicle ahead. If it judges there is a very high possibility of a collision, it applies the brakes.

The ASTM Sequence VE test evaluates lubricant performance for controlling sludge deposits and minimizing overhead camshaft lobe wear. ILSAC asked JAMA to develop a new valve train wear replacement test since the Sequence VE test engine hardware will become obsolete in the year 2000. JAMA submitted the JASO specification M 328-951) KA24E valve train wear test. This first report presents the results of technical studies conducted when JASO M 328-95 was reviewed and the ASTM standardized version of the KA24E test (the Sequence IVA) was proposed. The cam wear mechanism was studied with the goal of improving reproducibility and repeatability. Engine torque was specified to stabilize the NOx concentration in blow-by, which improved test precision. Additionally, the specifications for induction air humidity and temperature, oil temperature control, and test fuel composition were modified when the ASTM version of the KA24E test was proposed.

Two working groups in the JSAE Committee of Fatigue–Reliability Section1 are currently researching the issue of fatigue life by both experimental and the CAE approach. Information regarding frequent critical problems on arc–welded structures were sought from auto–manufacturers, vehicle component suppliers, and material suppliers. The method for anti–fatigue design on arc–welded structures was established not only by a database created by physical test results in accordance with the collected information but also with design procedure taking Fracture–Mechanics into consideration. This method will be applied to vehicle development as one of the virtual laboratories in the digital prototype phase. In this paper, both the database from bench–test results on arc welded structures and FEA algorithm unique to JSAE are proposed some of the analysis results associated with the latter proposal are also reported.

In the past few years, car navigation and cellular phone system are rapidly increased in Japan and vehicle information and communication system (VICS), the public traffic information service started in 1996, accelerates realization of ITS world. This rapid movement causes drivers to want more information on not only traffic jam but also other versatile items like parking availability, weather report and the latest news, etc. via cellular phone network. This paper describes the on-demand information service with the interactive human interface by operators and the development of the information center and the in-vehicle system to realize it.

Detergent additives in automotive gasoline fuel are mainly designed to reduce deposit formation on intake valves and fuel injectors, but it has been reported that some additives may contribute to CCD formation. Therefore, a standardized bench engine test method for CCDs needs to be developed in response to industry demands. Cooperative research between the Petroleum Association of Japan (PAJ) and the Japan Automobile Manufacturers Association, Inc. (JAMA), has led to the development of a 2.2L Honda engine dynamometer-based CCD test procedure to evaluate CCDs from fuel additives. Ten automobile manufacturers, nine petroleum companies and the Petroleum Energy Center joined the project, which underwent PAJ-JAMA round robin testing. This paper describes the CCD test development activities, which include the selection of an engine and the determination of the optimum test conditions and other test criteria.

The Inter-Industry Emission Control (IIEC) Program included the thermal reactor as one of the effective ways of oxidizing HC and CO in the exhaust system. However, this was accompanied by very substantial fuel economy penalties, especially in the case of small engine-low emission concept vehicles. Starting with a new concept aimed at obtaining the HC/CO oxidizing trigger temperature in the thermal reactor by modifying engine settings, the authors arrived at an economical technique of matching the thermal reactor to the engine.