Search Results

The work examined the practicality of converting a modern production 6 cylinder 7.7 litre heavy-duty diesel engine for flex dual-fuel operation with ammonia as the main fuel. A small amount of diesel fuel (pilot) was used as an ignition source. Ammonia was injected into the intake ports during the intake stroke, while the original direct fuel injection equipment was retained and used for pilot diesel injection. A bespoke engine control unit was used to control the injection of both fuels and all other engine parameters. The aim was to provide a cost-effective retrofitting technology for existing heavy-duty engines, to enable eco-friendly operation with minimal carbon emissions. The tests were carried out at a baseline speed of 600 rpm for the load range of the engine (10-90%), with minimum pilot diesel quantity and as high as 90% substitution ratio of ammonia for diesel fuel.

Ammonia (NH3) is emerging as a potential fuel for longer range decarbonised heavy transport, predominantly due to favourable characteristics as an effective hydrogen carrier. This is despite generally unfavourable combustion and toxicity attributes, restricting end use to applications where robust health and safety protocols can always be upheld. In the currently reported work, a spark ignited thermodynamic single cylinder research engine was upgraded to include gaseous ammonia and hydrogen port injection fueling, with the aim of understanding maximum viable ammonia substitution ratios across the speed-load operating map. The work was conducted under stoichiometric conditions with the spark timing re-optimised for maximum brake torque at all stable logged sites. The experiments included industry standard measurements of combustion, performance and engine-out emissions.

Mo-free 1.6-GPa bolt was developed for a Variable Compression Turbo (VC-Turbo) engine, which is environment friendly and improves fuel efficiency and output. Mo contributes to the improvement of delayed fracture resistance; therefore, the main objective is to achieve both high strength and delayed fracture resistance. Therefore, Si is added to the developed steel to achieve high strength and delayed fracture resistance. The delayed fracture tests were performed employing the Hc/He method. Hc is the limit of the diffusible hydrogen content without causing a delayed fracture under tightening, and He is the diffusible hydrogen content entering under a hydrogen-charging condition equivalent to the actual environment. The delayed fracture resistance is compared between the developed steel and the SCM440 utilized for 1.2-GPa class bolt as a representative of the current high-strength bolts.

Recent legislation banning the sale of new petrol and diesel vehicles in Europe from 2035 has shifted the focus of internal combustion engine research towards alternative fuels with net zero tailpipe emissions such as hydrogen. Research regarding hydrogen as a fuel is particularly pertinent to the so-called ‘hard-to-electrify’ propulsion applications, requiring a combination of large range, fast refuelling times or high-load duty cycles. The virtual design, development, and optimisation of hydrogen internal combustion engines has resulted in the necessity for accurate predictive modelling of the hydrogen combustion and autoignition processes. Typically, the models for these processes rely respectively on laminar flame speed datasets to calculate the rate of fuel burn as well as ignition delay time datasets to estimate autoignition timing. These datasets are generated using chemical kinetic mechanisms available in the literature.

To improve the fuel economy, we developed a turbo-charged spark ignition engine combined with a low pressure loop EGR system. A negative pressure control valve has been applied to achieve high EGR ratio in wide engine operation condition. In this paper, a new developed model-based control system for low pressure loop EGR with a negative pressure control valve will be described.

A gasoline particulate filter (GPF) is installed in a passenger vehicle for new exhaust regulation. However, ash in gasoline engine oil has a risk of clogging as well as performance decrease in the GPF. Therefore, new gasoline engine oil whose ash contents decrease to 0.8 mass% was developed in order to avoid the GPF clogging. In addition to this, our developed oil improves fuel efficiency (+0.2% from our SN 0W-16 fuel eco type oil) as well as anti-wear performance for gasoline engine, which resulted in meeting API SP/ILSAC GF-6 0W-16 official certification.

One of the main challenges in internal combustion engine design is the simultaneous reduction of all engine pollutants like carbon monoxide (CO), total unburned hydrocarbons (THC), nitrogen oxides (NOx), and soot. Low-temperature combustion (LTC) concepts for compression ignition (CI) engines, e.g., premixed charged compression ignition (PCCI), make use of pre-injections to create a partially homogenous mixture and achieve an emission reduction. However, they present challenges in the combustion control, with the usage of in-cylinder pressure sensors as feedback signal is insufficient to control heat release and pollutant emissions simultaneously. Thus, an additional sensor, such as an ion-current sensor, could provide further information on the combustion process and effectively enable clean and efficient PCCI operation.

Porous wall permeability is one of the most critical factors for the estimation of backpressure, a key performance indicator in automotive particulate filters. Current experimental and analytical filter models could be calibrated to predict the permeability of a specific filter. However, they fail to provide a reliable estimation for the dependence of the permeability on key parameters such as wall porosity and pore size. This study presents a novel methodology for experimentally determining the permeability of filter walls. The results from four substrates with different porosities and pore sizes are compared with several popular permeability estimation methods (experimental and analytical), and their validity for this application is assessed. It is shown that none of the assessed methods predict all permeability trends for all substrates, for cold or hot flow, indicating that other wall properties besides porosity and pore size are important.

In electrified automobiles, wind noise significantly contributes to the overall noise inside the cabin. In particular, underbody airflow is a dominant noise source at low frequencies (less than 500 Hz). However, the wind noise transmission mechanism through a battery electric vehicle (BEV) underbody is complex because the BEV has a battery under the floor panel. Although various types of underbody structures exist for BEVs, in this study, the focus was on an underbody structure with two surfaces as inputs of wind noise sources: the outer surface exposed to the external underbody flow, such as undercover and suspension, and the floor panel, located above the undercover and battery. In this study, aero-vibro-acoustic simulations were performed to clarify the transmission mechanism of the BEV underbody wind noise. The external flow and acoustic fields were simulated using computational fluid dynamics.

With ever stricter legislative requirements for CO2 and other exhaust emissions, significant efforts by OEMs have launched a number of different technological strategies to meet these challenges such as Battery Electric Vehicles (BEVs). However, a multiple technology approach is needed to deliver a broad portfolio of products as battery costs and supply constraints are considerable concerns hindering mass uptake of BEVs. Therefore, further investment in Internal Combustion (IC) engine technologies to meet these targets are being considered, such as lean burn gasoline technologies alongside other high efficiency concepts such as dedicated hybrid engines. Hence, it becomes of sound reason to further embrace diversity and develop complementary technologies to assist in the transition to the next generation hybrid powertrain. One such approach is to provide increased valvetrain flexibility to afford new degrees of freedom in engine operating strategies.

This paper describes the equivalent temperature based on the mesh-free simulation proposed by the previous papers (Part1 and Part2) under the transient heating condition in a 3D-CAD vehicle cabin including the thermal manikin which takes into account the clothing shape. For this purpose, firstly, the experiments of vehicle cabin measuring for the thermal environment including the equivalent temperature are carried out under the transient heating condition. Then, the calculated results of the thermal environment in the vehicle cabin are compared with time series experimental data under the transient condition. They correspond to the experiments including transient changes well. The transient calculated equivalent temperature of thermal manikin is also compared with experiments. As a result, since it is difficult to control the thermal manikin ideally in the experiment, it is difficult to compare the transient behavior.

This paper describes a method for evaluating the equivalent temperature in vehicle cabins based on the new international standard ISO 14505-4, published in 2021. ISO 14505-4 defines two simulation methods to determine a thermal comfort index “equivalent temperature.” One method uses a numerical thermal manikin, and the other uses thermal factors to calculate. This study discusses the latter method to validate its accuracy, identify the key points to consider, and examine its advantages and disadvantages. First, the definition of equivalent temperature and the equation to calculate the equivalent temperature using thermal factors, such as air temperature, radiant temperature, solar radiation, and air velocity, are explained. In addition, the experiments and simulation methods are described.

The present work represents the continuation of the introductory study presented in part I [11] where the experimental plan, the measurement system and the tools developed for the testing of a modern Wankel engine were illustrated. In this paper the motored data coming from the subsequent stage of the testing are presented. The AIE 225CS Wankel rotary engine produced by Advanced Innovative Engineering UK, installed in the test cell of the University of Bath and equipped with pressure transducers selected for the particular application, has been preliminarily tested under motored conditions in order to validate the data acquisition software on the real application and the correct determination of the Top Dead Centre (TDC) location which is of foremost importance in the computation of parameters such as the indicated work and the combustion heat release when the engine is tested later under fired conditions.

The paper presents results from a study into the potential of a complex cycle gas turbine engine, originally investigated by the Ford Motor Company for truck applications in the 1960s, and updated to gauge the possible improvements by raising the efficiencies of its constituent components from the values used in period to more modern levels. To perform this investigation, firstly a spreadsheet model was constructed and the data that Ford made available in the open literature were used to validate it. The methodology used in the model was to balance the power consumed by the compressors (and the auxiliaries where applicable) with that produced by their driving turbines, and to match the thermal power in the heat exchangers with the data provided. Using the quoted lower heating value of the diesel fuel originally used, this approach led to an accuracy in the match of brake specific fuel consumption (in terms of g/kWh) to three places of decimals.

Permanent magnet (PM) electrical machine has far-reaching impacts in aviation electrification due to the continuous development in high power density and high efficiency electrical drives. The primary barrier to acceptance of permanent magnet machines for safety-critical starter-generator systems is its low fault-tolerance capability and low reliability (for the conventional designs). This article investigates a modular triple three-phase PM starter-generator comprehensively, including the tradeoff of fault-tolerant topology, optimization design process, analysis of electromagnetic (highlight the post-fault analysis) and thermal behavior, respectively. The triple three-phase segmented topology proposed meet the fault-tolerant requirement along with complete electrical, magnetic, and thermal isolation. There would be cost penalty on the proposed topology, but it gets offset by the ease of manufacturing of coils and their insertion.

Evolving of aircraft design towards further electrification requires safe and fault-free operation of all the components. More electric aircraft are increasingly utilizing electro-mechanical actuators (EMA). EMAs are prone to jamming and subsequent failure due to large forces on the shaft. Large forces are generated due to the high reflected inertia of the electric machine rotor. To limit the force acting on the shaft, a torque limiting device is connected to the power train which can separate the rotating mass of the electric machine from the power train. In this paper, a concept of integration of torque limiter and the electric machine rotor is presented to reduce overall volume and mass. It is connected closely with the rotor, within the motor envelope. A commercially available torque limiter and an electric machine designed for actuator application are used to demonstrate the concept. While essential for safety, the torque limiter adds to the mass and size of the overall EMA.

The increased severity and prevalence of insoluble deposits formed on fuel injectors in gasoline direct injection (GDI) engines precipitates negative environmental, economic and healthcare impacts. A necessary step in mitigating deposits is to unravel the molecular compositions of these complex layered materials. But very little molecular data has been acquired. Mass spectrometry shows promise but most techniques require the use of solvents, making them unsuited for analyzing insoluble deposits. Here, we apply the high mass-resolving power and in-situ analysis capabilities of 3D OrbitrapTM secondary ion mass spectrometry (3D OrbiSIMS) to characterize deposits formed on the external tip and internal needle from a GDI injector. This is the first application of the technique to study internal GDI deposits. Polycyclic aromatic hydrocarbons (PAHs) are present up to higher maximum masses in the external deposit.

The present work investigates a means of controlling engine hydrocarbon startup and shutdown emissions in a Wankel engine which uses a novel rotor cooling method. Mechanically the engine employs a self-pressurizing air-cooled rotor system (SPARCS) configured to provide improved cooling versus a simple air-cooled rotor arrangement. The novelty of the SPARCS system is that it uses the fact that blowby past the sealing grid is inevitable in a Wankel engine as a means of increasing the density of the medium used for cooling the rotor. Unfortunately, the design also means that when the engine is shutdown, due to the overpressure within the engine core and the fact that fuel vapour and lubricating oil are to be found within it, unburned hydrocarbons can leak into the combustion chambers, and thence to the atmosphere via either or both of the intake and exhaust ports.

Particulate emissions from gasoline direct injection (GDI) engines continue to be a topic of substantial research interest. Forthcoming regulation both in the USA and the EU will further reduce their emission and drive innovation. Substantial research effort is spent undertaking experiments to understand, characterize, and research particle number (PN) emissions from engines and vehicles. Recent advances in computing power, data storage, and understanding of artificial intelligence algorithms now mean that these are becoming an important tool in engine research. In this work a random forest (RF) algorithm is used for the prediction of PN emissions from a highly boosted (up to 32 bar BMEP) GDI engine. Particle size, concentration, and the accumulation mode geometric standard deviation (GSD) are all predicted by the model. The results are analysed and an in depth study on parameter importance is carried out.

Engine research has increasingly focused on emission of sub 23 nm particulates in recent years. Likewise, current legislative efforts are being made for particulate number (PN) emission limits to include this previously omitted size range. In Europe, PN measurement equipment and procedures for regulatory purposes are defined by the particle measurement programme (PMP). Latest regulation drafts for sub 23 nm measurements specify counting efficiencies with a 65% cut-off size at 10 nm (d65) and a minimum of 90% above 15 nm (d90). Even though alternative instruments, such as differential mobility spectrometers (DMS), are widely used in laboratory environments, the interpretation of their sub 23 nm measurements has not yet been widely discussed. For this study, particulate emissions of a 1.0L gasoline direct injection (GDI) engine have been measured with a DMS system for low to medium speeds with two load steps.