Search Results

The CFR engine is the widely accepted platform to test standard Research Octane Number (RON) and Motored Octane Number (MON) for determining anti-knock characteristics of motor fuels. With increasing interest in engine downsizing, up-torquing, and alternative fuels for modern spark ignition (SI) engines, there is a need to better understand the conditions that fuels are subjected to in the CFR engine during octane rating. To take into account fuel properties, such as fuel heat of vaporization, laminar flame speed and auto-ignition chemistry; and understand their impacts on combustion knock, it is essential to estimate accurate cylinder conditions. In this study, the CFR F1/F2 engine was modeled using GT-Power with the Three Pressure Analysis (TPA) and the model was validated for different fuels and engine conditions.

Detailed characteristics of particulate matter (PM) from a gasoline-direct-injection (GDI) engine were analyzed in terms of primary and aggregate particle sizes, morphology, and nanostructures. For the work, PM was collected from exhaust streams of the engine on transmission electron microscope (TEM) grids by using a thermophoretic sampler. To evaluate the effects of engine load and speed on the properties of PM, the engine was operated at loads of 25, 50, and 75% at 1500 and 3000 rpm. In addition, the effects of fuel injection timing on the PM were examined for samples subjected to injection timings of 190, 230, 260, 300 and 330° bTDC at the constant engine load (50% load) and speed (1500 rpm). The results showed that with advancing injection timing, average primary and aggregate particle sizes gradually increased, which implies that fuel-air mixing is a crucial factor influencing particle size.

Detailed characteristics of morphology, nanostructures, and sizes were analyzed for particulate matter (PM) emissions from low-temperature combustion (LTC) modes of a single-cylinder, light-duty diesel engine. The LTC engines have been widely studied in an effort to achieve high combustion efficiency and low exhaust emissions. Recent reports indicate that the number of nucleation mode particles increased in a broad engine operating range, which implies a negative impact on future PM emissions regulations in terms of the nanoparticle number. However, the size measurement of solid carbon particles by commercial instruments is indeed controversial due to the contribution of volatile organics to small nanoparticles. In this work, an LTC engine was operated with various biofuel blends, such as blends (B20) of soy bean oil (soy methyl ester, SME20) and palm oil (palm methyl ester, PME20), as well as an ultra-low-sulfur diesel fuel.

At the current stage of engine technology, diesel engines typically require diesel particulate filter (DPF) systems to meet recent particulate emissions standards. To assure the performance and reliability of DPF systems, profound understanding of filtration and regeneration mechanisms is required. Among extensive efforts for developing advanced DPF systems, the development of effective thermal management strategies, which control the thermal runaway taking place in oxidation of an excess amount of soot deposit in DPF, is quite challenging. This difficulty stems mainly from lack of sufficient knowledge and understanding about DPF regeneration mechanisms, which need detailed information about oxidation of diesel particulate matter (PM). Therefore, this work carried out a series of oxidation experiments of diesel particulates collected from a DPF on a diesel engine, and evaluated the oxidation rates of the samples using a thermo-gravimetric analyzer (TGA).

Exhaust gas recirculation (EGR) is a commonly used technique for the reduction of Nitrogen oxide (NOx) emissions from internal combustion engines. However, it is generally known that the use of EGR will cause an increase in emissions of particulate matter (PM). The effects of EGR operating mode on particulate morphology were investigated for a 1.7-liter light-duty diesel engine. This engine was equipped with a turbocharged and inter-cooled air induction system, a common-rail direct fuel injection system, and an EGR system. A rapid prototyping electronic control system (RPECS) was developed to operate this engine at various EGR rates under different conditions (i.e. constant boost pressure, constant oxygen-to-fuel ratio (OFR)). A unique thermophoretic sampling system was employed to collect particulates directly from exhaust manifold after exhaust valves.

The particulate matter (PM) produced from a diesel engine-simulating combustor was characterized in its morphology, microstructure, and fractal geometry by using a unique thermophoretic sampling and Transmission Electron Microscopy (TEM) system. These results revealed that diesel PM produced from the laboratory-scale burner showed similar morphological characteristics to the particulates produced from diesel engines. The flame air/fuel ratio and the particulate temperature history have significant influences on both particle size and fractal geometry. The primary particle sizes were measured to be 14.7 nm and 14.8 nm under stoichiometric and fuel-rich flame conditions, respectively. These primary particle sizes are smaller than those produced from diesel engines. The radii of gyration for the aggregate particles were 83.8 nm and 47.5 nm under these two flame conditions.