Search Results

The current work presents the results of an investigation on the impact of renewable fuels on the combustion and emissions of a turbocharged compression-ignition internal combustion engine. An experimental study was undertaken and the engine settings were not modified to account for the fuel's chemical and physical properties, to analyze the performance of the fuel as a potential drop-in alternative fuel. Three fuels were tested: mineral diesel, a blend of it with waste cooking oil biodiesel and a hydrogenated diesel. The analysis of the emissions at engine exhaust highlights that hydrogenated fuel allows to reduce CO, total hydrocarbon emissions, particulate matter and NOx.

This paper presents an optimal control co-design framework of a parallel electric-hydraulic hybrid powertrain specifically tailored for heavy-duty vehicles. A pure electric powertrain, comprising a rechargeable lithium-ion battery, a highly efficient electric motor, and a single or double-speed gearbox, has garnered significant attention in the automotive sector due to the increasing demand for clean and efficient mobility. However, the state-of-the-art has demonstrated limited capabilities and has struggled to meet the design requirements of heavy-duty vehicles with high power demands, such as a class 8 semi-trailer truck. This is especially evident in terms of a driving range on one battery charge, battery charging time, and load-carrying capacity. These challenges primarily stem from the low power density of lithium-ion batteries and the low energy conversion efficiency of electric motors at low speeds.

In-cylinder pressure measurement is an important tool in internal combustion engine research and development for combustion, cycle performance, and knock analysis in spark-ignition engines. In a typical laboratory setup, a sub crank angle resolved (typically between 0.1o and 0.5o) optical encoder is installed on the engine crankshaft, and a piezoelectric pressure transducer is installed in the engine cylinder. The charge signal produced by the transducer due to changes in cylinder pressure during the engine cycle is converted to voltage by a charge amplifier, and this analog voltage is read by a high-speed data acquisition (DAQ) system at each encoder trigger pulse. The high speed of engine operation and the need to collect hundreds of engine cycles for appropriate cycle-averaging requires significant processor speed and memory, making typical data acquisition systems very expensive.

Engineering design-decisions often involve many attributes which can differ in the levels of their importance to the decision maker (DM), while also exhibiting complex statistical relationships. Learning a decision-making policy which accurately represents the DM’s actions has long been the goal of decision analysts. To circumvent elicitation and modeling issues, this process is often oversimplified in how many factors are considered and how complicated the relationships considered between them are. Without these simplifications, the classical lottery-based preference elicitation is overly expensive, and the responses degrade rapidly in quality as the number of attributes increase. In this paper, we investigate the ability of deep preference machine learning to model high-dimensional decision-making policies utilizing rankings elicited from decision makers.

Spark ignition engines utilize catalytic converters to reform harmful exhaust gas emissions such as carbon monoxide, unburned hydrocarbons, and oxides of nitrogen into less harmful products. Aftertreatment devices require the use of expensive catalytic metals such as platinum, palladium, and rhodium. Meanwhile, tightening automotive emissions regulations globally necessitate the development of high-performance exhaust gas catalysts. So, automotive manufactures must balance maximizing catalyst performance while minimizing production costs. There are thousands of different recipes for catalytic converters, with each having a different effect on the various catalytic chemical reactions which impact the resultant tailpipe gas composition. In the development of catalytic converters, simulation models are often used to reduce the need for physical parts and testing, thus saving significant time and money.

The emergence of new electric vehicle (EV) corner concepts with in-wheel motors offers numerous opportunities to improve handling, comfort, and stability. This study investigates the potential of controlling the vehicle's corner positioning by changing wheel toe and camber angles. A high-fidelity simulation environment was used to evaluate the proposed solution. The effects of the placement of the corresponding actuators and the actuation point on the force required during cornering were investigated. The results demonstrate that the toe angle, compared to the camber angle, offers more effect for improving the vehicle dynamics. The developed direct yaw rate control with four toe actuators improves stability, has a positive effect on comfort, and contributes to the development of new active corner architectures for electric and automated vehicles.

Making a sturdy battery box or enclosure is one of the many challenging issues that the expansion of electrification entails. Many characteristics of an effective battery housing contribute to the safety of passengers and shield the battery from the harsh environment created by vibrations and shocks due to varying road profiles in the vehicle. This results in stress and deformations of different degrees. There is a need to understand and develop a correlation between structural performance and lightweight design of battery enclosure as this can increase the range of the drive and the life cycle of a battery pack. This paper investigates the following points: I) A conceptualized CAD model of battery enclosure is developed to understand the design parameters such as utilization of different material for strength and structural changes for performance against vibration and strength.

A finite element/contact mechanics (FE/CM) method is used to determine the tooth contact forces, static transmission error, and tooth pair stiffnesses for spur gear pairs that have pitting damage. The pitting damage prevents portions of the tooth surface from carrying load, which results in meaningfully different contact pressure distribution on the gear teeth and deformations at the mesh. Pits of elliptical shape are investigated. Parametric analyses are used to investigate the effect of pit width (along the tooth face) and height (along the tooth profile) on the gear tooth mesh interface. Pitting damage increases static transmission error and decreases tooth pair stiffness. Tooth contact forces differ only in the portions of the mesh cycle when multiple pairs of teeth are in contact and share the transmitted load. Pitting damage does not change the loads when only a single pair of teeth are in contact.

The IC engine still plays an important role in global markets, although electrified vehicles are highly demanded in some markets. Emission requirements for stoichiometric operation are challenging. This requires the bolted joints for turbo, EGR (Exhaust Gas Recirculation) and exhaust manifold to work under much higher temperature than before. How to avoid fastener breakage due to bolt bending caused by cyclic changes of the thermal conditions in engines is a big challenge. The temperatures of the components in the exhaust, EGR (Exhaust Gas Recirculation) and turbo systems change from ambient temperature to about 800 ~ 1000 °C when engines run at peak power with wide-open throttle. The temperature change induces catastrophic cyclic bending and axial strain to the fasteners. This research describes a method to reduce the cyclic bending displacement in the fasteners using a low friction washer.

The new corner-based architecture of electrified road vehicles requires a redesign of vehicle suspension components. The design protocol must satisfy the target parameters derived from dynamics requirements. The roll stiffness of the anti-roll bar is a crucial parameter for the handling performance of a vehicle. During the development of a new suspension, the design of the anti-roll bar needs to be modified. To this aim, two-dimensional beam theory models can quickly provide a preliminary design of this component. However, the simplified models might be inaccurate due to the three-dimensional and complex shapes of the bars. The present study aims to overcome this limitation. An analytical beam model based on the spline description of the bar has been developed, which is accurate even for complex geometries of the bars. Assuming a hollow and closed circular cross-section, the model returns the average diameter and the radial thickness needed to achieve the stiffness performance.

Autonomous vehicle navigation, both global and local, makes use of large amounts of multifactorial data from onboard sensors, prior information, and simulations to safely navigate a chosen terrain. Additionally, as each mission has a unique set of requirements, operational environment and vehicle capabilities, any fixed formulation for the cost associated with these attributes is sub-optimal across different missions. Much work has been done in the literature on finding the optimal cost definition and subsequent mission pathing given sufficient measurements of the preference over the mission factors. However, obtaining these measurements can be an arduous and computationally expensive task. Furthermore, the algorithms that utilize this large amount of multifactorial data themselves are time consuming and expensive.

In the automotive industry, performing steady-state tests on an internal combustion engine can be a time consuming and costly process, but it is necessary to ensure the engine meets performance and emissions criteria set by the manufacturer and regulatory agencies. Any measures that can reduce the amount of time required to complete these testing campaigns provides significant benefits to manufacturers. The purpose of this work is then to develop a systematic approach to minimize the time required to conduct a steady-state engine test campaign using a Savitsky-Golay filter to calculate measured signal gradients for continuous steady-state detection. Experiments were conducted on an Armfield CM11-MKII Gasoline Engine test bench equipped with a 1.2L 3-cylinder Volkswagen EA111 R3 engine. The test bench utilizes throttle position control and an eddy current dynamometer braking system with automatic PID control of engine speed.

Vacuum suction cups are used as transforming handles in stamping lines, which are essential in developing automation and mechanization. However, the vacuum suction cup will crack due to fatigue or long-term operation or installation angle, which directly affects production productivity and safety. The better design will help increase the cups' service life. If the location of stress concentration can be predicted, this can prevent the occurrence of cracks in advance and effectively increase the service life. However, the traditional strain measurement technology cannot meet the requirements of tracking large-field stains and precise point tracking simultaneously in the same area, especially for stacking or narrow parts of the suction cups. The application must allow multiple measurements of hidden component strain information in different fields of view, which would add cost.

Digital shearography has many advantages, such as full-field, non-contact, high sensitivity, and good robustness. It was widely used to measure the deformation and strain of materials, also to the application of nondestructive testing (NDT). However, most digital sherography applications can only work in one field of view per measurement, and some small defects may not be detected as a result. Multiple measurements of different fields of view are needed to solve this issue, which will increase the measurement time and cost. The difficulty in performing multiple measurements may also increase for cases where the loading is not repeatable. Therefore, a system capable of measuring dual fields of view at the same time is necessary. The carrier frequency spatial phase shift method may be a good candidate to reach this goal because it can simultaneously record phase information of multiple images, e.g. two speckle interferograms with different fields of view.

Engineering practice routinely involves decision making under uncertainty. Much of this decision making entails reconciling multiple pieces of information to form a suitable model of uncertainty. As more information is collected, one expectedly makes better and better decisions. However, conditional probability assessments made by human decision makers, as new information arrives does not always follow expected trends and instead exhibits inconsistencies. Understanding them is necessary for a better modeling of the cognitive processes taking place in their mind, whether it be the designer or the end-user. Doing so can result in better products and product features. Quantum probability has been used in the literature to explain many commonly observed deviations from the classical probability such as: question order effect, response replicability effect, Machina and Ellsberg paradoxes and the effect of positive and negative interference between events.

Mobility in the automotive and transportation sectors has been experiencing a period of unprecedented evolution. A growing need for efficient, clean and safe mobility has increased momentum toward sustainable technologies in these sectors. Toward this end, battery electric vehicles have drawn keen interest and their market share is expected to grow significantly in the coming years, especially in light-duty applications such as passenger cars. Although the battery electric vehicles feature high performance and zero tailpipe emission characteristics, economic and technical issues such as battery cost, driving range, recharging time and infrastructure remain main hurdles that need to be fully addressed. In particular, the low power density of the battery limits its broad adoption in heavy-duty applications such as class 8 semi-trailer trucks due to the required size and weight of the battery and electric motor.

Fasteners, commonly used in automotive industry, play an important role in the safety and reliability of the vehicle structural system. In practical application, bolted joints would never undergo fully reversed loading; there always will be positive mean stress on bolt. The mean stress has little influence on the fatigue life if the maximum stress is lower than a threshold which is near the yield stress of the bolt. However, when the sum of the mean stress and the stress amplitude exceeds the threshold, the endurance limit stress amplitude decreases fast as the mean stress increases. The purpose of this paper is to research the fatigue endurance limit of a fastener and establish the threshold for safe design in automotive application. In order to obtain the fatigue endurance limit at different mean stress levels, various mechanical tests were performed on M12x1.75 and M16x1.5 Class 10.9 fasteners using MTS test systems.

This paper proposes a new nonlinear model predictive control (NMPC) for autonomous vehicle path tracking problem. The vehicle is equipped with active rear steering, allowing independent control of front and rear steering. Traditional NMPC, which runs at fixed sampling rate, has been shown to provide satisfactory control performance in this problem. However, the high throughput of NMPC limits its implementation in production vehicle. To address this issue, we propose a novel event-triggered NMPC formulation, where the NMPC is triggered to run only when the actual states deviate from prediction beyond certain threshold. In other words, the event-triggered NMPC will formulate and solve a constrained optimal control problem only if it is enabled by a trigger event. When NMPC is not triggered, the optimal control sequence computed from last NMPC instance is shifted to determine the control action.

Increasing the demand for EV charging has increased the burden and accretion of the power quality issues. Harmonic voltages and currents have a significant negative influence on power system components, specifically power transformers. The voltage and current harmonics created by EV chargers and their impacts on power transformers have been discussed in this paper, and an approach is proposed to reduce such harmonics in the system. For this purpose, firstly, the total harmonic distortion (THD) of a typical EV charger is evaluated. Then an analysis is performed utilizing Fast Fourier Transform (FTT) to extract individual harmonics. To this end, this paper addresses the power quality issues on the power transformers by implementing a passive filter. The harmonic voltages and currents were measured on different levels of charging loads. The simulation results show that more than 30% of total harmonic distortions were reduced to 1.16% using a passive filter.

The presented paper is dedicated to the driving comfort evaluation in the case of the electric vehicle architecture with four independent wheel corners equipped with in-wheel motors (IWMs). The analysis of recent design trends for electrified road vehicles indicates that a higher degree of integration between powertrain and chassis and the shift towards a corner-based architecture promises improved energy efficiency and safety performances. However, an in-wheel-mounted electric motor noticeable increases unsprung vehicle mass, leading to some undesirable impact on chassis loads and driving comfort. As a countermeasure, a possible solution lies in integrated active corner systems, which are not limited by traditional active suspension, steer-by-wire and brake-by-wire actuators. However, it can also include actuators influencing the wheel positioning through the active camber and toe angle control.