Search Results

One of the prime requisites for automobile radar systems is obstacle hazard evaluation, the extent needed being dependent upon the particular system application. Much of the information necessary for a radar system to assess the degree of hazard of a target must come from characteristics which can be measured by the radar itself. While the hazard evaluation capacity has not yet been developed for automobile radar systems, research to provide this capability is in progress. Continuous wave (CW) scattering measurements have been made in a manner which is consistent with automobile radar operation. Various aspects of simple targets and of an automobile were measured in a microwave anechoic chamber. Both horizontal and vertical linear polarizations were transmitted and their co-linear and cross polarizations received. These data have been used to confirm the existence of and to understand certain scattering mechanisms.

A general purpose data acquisition system has been developed which converts analog data to scaled, tabulated, and graphical output. A scanning synchronization unit ensures that each input channel is sampled synchronously with input data pulses. System input can be either direct from the test area or from an analog tape recorder, in which case time expansion is possible by the use of high record-low play/back speeds. A computer program controls the analog to digital conversion process. The on-line control of the program minimizes the subsequent data reduction, and through the use of input parameters, flexibility is attained in data formatting. The data reduction error is less than 1% and statistical programs included in the system provide estimates of the quality of the input data. The entire system including all associated hardware and software is described in detail, using acquisition of pressure data synchronously with crank angle as an example.

Several polymeric materials were developed and evaluated for possible inclusion in the neck structure of state-of-the-art anthropomorphic dummies. These included three types of foam-polyvinylchloride, polyethylene, and polyurethane, and two flexible polymers-polyurethane and a polyvinylchloride chlorinated polyethylene blend (PVC-CPE). Two materials, the polyurethane elastomer and the PVC-CPE blend, were found to be satisfactory in their dynamic response. Because of the ease of casting, the polyurethane material will be used in the GMR 1 state-of-the-art dummy.

Tests of laser ignition are conducted in a combustion bomb. A range of fuels is investigated comprising isooctane, cyclohexane, n-heptane, n-hexane, clear indolene, and No. 1 diesel fuel. The ignition characteristics of laser-induced sparks are compared with sparks generated with a spark plug for different air/fuel ratios. The power density required to produce laser induced sparks is investigated. Although laser ignition appears to be impractical as an ignition device because of its low efficiency and high cost, it presents some interesting possibilities compared to the standard spark plug in that the laser spark is electrodeless and can be positioned anywhere inside the combustion chamber. Its primary use appears to be as a research tool.

Two Highway Safety Research Institute (HSRI) dummies were tested and evaluated. Based on the analysis given, the HSI dummy should not be used for vehicle qualification testing. However, many of its components offer viable alternatives for future dummy development. The dummy was found to have inadequate biomechanical fidelity in the head, neck, and chest, although its characteristics were very promising and, as a whole, biomechanically superior to the Hybrid II. Its repeatability and reproducibility in dynamic component tests were better than the Hybrid II dummy. In particular, the HSRI friction joints were outstanding in repeatability and had a significant advantage in usability in that they do not require resetting between tests. In three-point harness and ACRS systems tests, the values of injury criteria produced by the HSRI dummy were generally lower than those obtained with the Hybrid II, especially the femur loads in the ACRS tests.

Noise produced by automotive ignition systems can deteriorate the performance of nearby communication systems. An important step toward alleviating this difficulty is to characterize the ignition noise. Measurements have been made of the noise peak amplitude distribution of a number of identically equipped vehicles over a fixed period of time. Both vertical and horizontal polarizations were used, and measurements were made at two frequencies, 145 and 230 MHz. These statistics were then compared to various probability distributions to attempt to characterize the amplitude distribution of the noise. The distributions studied were: the log-normal, the exponential, the Rayleigh, and the Weibull distributions. It was concluded that the best fit was provided by the Weibull distribution. The parameters of the best fitting distribution are primarily a function of the antenna's polarization, with frequency having only a minor effect.

This paper evaluates the tendency of lip seals to fracture in a test apparatus in which dynamic runout is 0.010 in and the temperature is cycled between -30 and 0 F. Seals made of eight different polyacrylate polymers were soap-sulfur cured with various types and amounts of carbon black. Physical tests included room-temperature flexibility defined by Young's modulus at small strains, standard tensile tests at room temperature, flexibility at sub-zero temperatures determined by a Gehman test, and sub-zero starting torques of the seals. Primary determinant of successful fracture resistance is a low starting torque resulting from good low-temperature flexibility. The effect of adding graphite to some of these formulations is described and some current commercially available seals are evaluated.

This paper summarizes an analysis, design, and test project in which a dummy chest structure was developed. The chest consisted of mechanical elements that had been characterized by computer simulations as giving responses to blunt frontal impacts necessary for biofidelity. An analysis of mechanical rib structures indicated that materials having a high ratio of yield stress to modulus of elasticity were required. Only metals having unusually high yield strengths, such as spring steels, qualified. A mechanical system was developed with steel ribs pivoted at each end as a primary spring. A secondary spring was a pair of commercially available die springs acting in parallel with the ribs after 25.4 mm (1.00 in) deflection. A fluid damper was developed to provide the damping. The chest structure was tested under conditions modified from those used by Kroell. The modifications were holding the spine rigidly and reducing the impact masses.

Most transducers offered commercially are suitable for laboratory, aerospace, or industrial process applications but do not meet additional, stringent automotive requirements. A need exists, both present and future, for various types of transducers in automotive powerplant control systems. Possible electronic systems and subsystems requiring transducers are discussed, and the types of transducers needed for these systems are described along with a discussion of a general set of specifications with respect to accuracy, reliability, and durability. Substantial transducer development is needed to enhance the advancement of certain automotive electronic systems. This paper points out these requirements to the electronics industry in an effort to encourage a mutual industry development that will advance the technology.

Various proposals for emissions cleanup systems have shown the desirability of regulating engine air-fuel ratio within precise limits. For this purpose a prototype exhaust sensor has been investigated. The sensor is a ceramic device, made of stabilized zirconia, which operates via electrochemical principles. It is placed directly in the exhaust stream and generates a voltage signal which is an approximate indication of engine air-fuel ratio. Several sensors have been installed in situ on engines operated under controlled dynamometer conditions. Fundamental response characteristics of the sensors have been determined. The results of this investigation, together with descriptions of the construction and installation configuration of the prototype sensor, are discussed.

The following work was done in support of a continuing program to better characterize the behavior of the human chest during blunt sternal impact. Previous work on this problem has focused on determining the force-time, deflection-time, and force-deflection response of embalmed and fresh cadavers to impact by a 15 cm (6 in) diameter striker of variable mass traveling at velocities of 22.5-51 km/h (14-32 mph) and striking the sternum at the level of the fourth intercostal space. Additional questions persist concerning whether the anterior and posterior regions of the chest behave as highly damped masses or oscillate after impact, the relationship between force delivered to the surface of the body and the acceleration of the underlying regions, and the influence of air compressed in the lung on thoracic mechanics.

A viscoelastic neck structure that responds to impact environments in a manner similar to the human neck is described. The neck structure consists of four ball-jointed segments and one pin-connected “nodding” segment with viscoelastic resistive elements inserted between segments that provide bending resistance as well as the required energy dissipation. Primary emphasis was placed on developing appropriate flexion and extension responses with secondary emphasis placed on axial, lateral, and rotational characteristics. The methods used to design the resistance elements for the neck structure are discussed. Three variations of the resistive elements have been developed that meet the response characteristics based on the data of Mertz and Patrick. However, no single resistive element has satisfied the flexion and extension characteristics simultaneously, but such an element appears to be feasible.

This study explores the application of viscoelastic modeling for characterization of the response of the brain to impulsive loading with the objective of learning whether such models could exhibit the same time dependency of strain or likelihood of injury, as exhibited by the Severity Index, HIC Index, Wayne Tolerance Curve, and other similar representations of tolerance. The mathematical relationships between viscoelastic properties and the corresponding time dependency of tolerance are shown for Newtonian, Bingham plastic, and Pseudo-Bingham, as well as more general behavior. Preliminary static and dynamic tests upon small mammalian material are described with particular attention given to strain in the vicinity of the brainstem as a function of loading profile. Both the theoretical and experimental results show that the falling time dependency of the above indexes can be interpreted in terms of nonlinear viscoelastic response.

At the 1970 SAE International Automobile Safety Conference, the first experimental chest impact results from a new, continuing biomechanics research program were presented and compared with earlier studies performed elsewhere by one of the authors using a different technique. In this paper, additional work from the current program is documented. The general objective remains unchanged: To provide improved quantification of injury tolerance and thoracic mechanical response (force-time, deflection-time, and force-deflection relationships) for blunt sternal impact to the human cadaver. Fourteen additional unembalmed specimens of both sexes (ranging in age from 19-81 years, in weight from 117-180 lb, and in stature from 5 ft 1-1/2 in to 6 ft) have been exposed to midsternal, blunt impacts using a horizontal, elastic-cord propelled striker mass. Impact velocities were higher than those of the previous work, ranging from 14-32 mph.

A professional high diver, instrumented with accelerometers, performed sixteen dives from heights between 27-57 ft. For each dive, he executed a 3/4 turn and landed supine on a 3-ft deep mattress which consisted of pieces of low-density urethane foam encased in a nylon cover. Using FM telemetry, sagittal plane decelerations were recorded for a point either on the sternum or the forehead. Impact velocities and corresponding stopping distances for the thorax and the head were calculated from high-speed movies of the dives. For a 57-ft dive, the impact velocity of the thorax was 41 mph with a corresponding stopping distance of 34.6 in. The peak resultant deceleration of the thorax was 49.2 g with a pulse duration of 100 ms. The maximum rate of change of the deceleration of the thorax was 5900 g/s. No discomfort was experienced as a result of this impact. The maximum forehead deceleration occurred during a 47.0-ft drop and exceeded 56 g with a Gadd Severity Index greater than 465.

The principal objectives of this study were first to obtain experimental curves of angulation versus moment of resistance of the human neck in hyperextension and lateral flexion, and second to determine angular limits short of significant injury observable in the unembalmed subjects employed in the study. The first of the tests were of the “static” type with load applied over a period of approximately 1s. To determine the applicability of the data to dynamic conditions, tests were also made of the dissected neck at angulation velocities comparable with those of typical accidental injury. Overall resisting moment and injury threshold were similar under the dynamic loading, but somewhat greater moment of resistance was noted during the (earlier) portion of the loading cycle when angular velocity was greatest.

Utilizing unembalmed cadaver test subjects, a series of tests was carried out to characterize quantitatively the resistance of the skin, the soft underlying tissue of the scalp, and certain other typical areas of the body to impact loading. The impacts were delivered by the use of an instrumented free-fall device similar to that previously employed for facial bone fracture experiments. In one group of tests, metal and glass edges were affixed to the impacting device to produce localized trauma under conditions which were standardized with respect to variables affecting the degree of the injury. In the second group of experiments, specimens of skin, together with underlying tissue of uniform thickness, were subjected to compressive impact between the parallel surfaces of the impacting weight and a heavy metal platen. From these latter experiments the force-time histories, coefficient of restitution, and hysteresis loops of load versus deflection were obtained for the specimens.

Forces necessary for fracture under localized loading have been obtained experimentally for a number of regions of the head. Three of these, the frontal, temporoparietal, and zygomatic, have been studied in sufficient detail to establish that the tolerances are relatively independent of impulse duration, in contrast with the tolerance of the brain to closed-skull injury. Significantly lower average strength has been found for the female bone structure. Other regions reported upon more briefly are mandible, maxilla, and the laryngotracheal cartilages of the neck. Pressure distribution has been measured over the impact area, which has been 1 sq in. in these tests, and the relationship between applied force as measured and as predicted from a head accelerometer is examined.

To promote improved automotive safety, present Federal specifications require the reduction of glare by sunlight reflection from a trim surface by restricting its intensity. The specifications imply that matte surfaces must be used. The alternative described herein reduces glare of reflected sunlight from reflective surfaces by decreasing the apparent size of the image. The necessary demagnification is obtained by utilization of surface curvature. The maximum radius of curvature is calculated by geometric optics.

The tedious, time consuming task of hand reducing data from the California exhaust emission test has been alleviated through the use of digital data acquisition equipment and a digital computer. Analog signals from exhaust gas analyzers and an engine speed transducer are converted to digital measurements which are recorded on tape and submitted to a digital computer for data analysis and computation of results. In the data analysis, the computer identifies the required driving modes from engine speed changes, taking into account the sample delay time. “Reported” composite emissions determined by the automatic data reduction method agree within 5% with results determined by careful hand analysis of analog strip chart recordings. The results determined by the automatic data reduction system are more consistent and accurate because human errors prevalent in hand analysis have been eliminated, and because nonlinear analyzer response is accounted for.