Search Results

The purpose of this work was to gain a fundamental understanding of which fuel property parameters are responsible for particulate emission characteristics, associated with key intermediate behavior in the engine cylinder such as the fuel film and insufficient mixing. Accordingly, engine tests were carried out using various fuels having different volatility and chemical compositions under different coolant temperature conditions. In addition, a fundamental spray and film visualization analysis was also conducted using a constant volume vessel, assuming the engine test conditions. As for the physical effects, the test results showed that a low volatility fuel displayed high particulate number (PN) emissions when the injection timing was advanced. The fundamental test clearly showed that the amount of fuel film on the impingement plate increased under such operating conditions with a low volatility fuel.

Certain diesel fuel specification properties are considered to be environmental parameters according to the European Fuels Quality Directive (FQD, 2009/EC/30) and previous regulations. These limits included in the EN 590 specification were derived from the European Programme on Emissions, Fuels and Engine Technologies (EPEFE) which was carried out in the 1990’s on diesel vehicles meeting Euro 2 emissions standards. These limits could potentially constrain FAME blending levels higher than 7% v/v. In addition, no significant work has been conducted since to investigate whether relaxing these limits would give rise to performance or emissions debits or fuel consumption benefits in more modern vehicles. The objective of this test programme was to evaluate the impact of specific diesel properties on emissions and fuel consumption in Euro 4, Euro 5 and Euro 6 light-duty diesel vehicle technologies.

Octane appetite of modern engines has changed as engine designs have evolved to meet performance, emissions, fuel economy and other demands. The octane appetite of seven modern vehicles was studied in accordance with the octane index equation OI=RON-KS, where K is an operating condition specific constant and S is the fuel sensitivity (RONMON). Engines with a displacement of 2.0L and below and different combinations of boosting, fuel injection, and compression ratios were tested using a decorrelated RONMON matrix of eight fuels. Power and acceleration performance were used to determine the K values for corresponding operating points. Previous studies have shown that vehicles manufactured up to 20 years ago mostly exhibited negative K values and the fuels with higher RON and higher sensitivity tended to perform better.

In a modern diesel engine, a high fuel injection pressure is achieved by a common-rail system. Therefore, it is important to understand the effects of fuel properties on engine performances because a diesel fuel could deteriorate inside an injector at such severe conditions. The test methods so far basically use the fuel with pro-fouling agent to form deposit on injector. In this study, a novel test procedure was developed to evaluate the effect of the use of the fuel with and without zinc contaminant on injector performance. With Zn doped European specification B7 fuel (7% biodiesel) as a reference, the test result showed that an engine torque decreased almost lineally over time, and the overall torque drop was 9% after 300 hours. The investigation of the dismantled injector after the test revealed that the deposit was not formed on the sliding parts of the injector, but on the nozzle hole surface.

This paper presents a statistical characterisation of the effects of variations in vehicle parameters on vehicle road load data using a quarter vehicle as a case study. A model of a quarter vehicle test rig constructed from a commercial SUV is created in a multi-body dynamics (MBD) simulation environment to reproduce the real-life behaviour of the SUV. The model is thereafter validated by correlating the response data collected from both the model and laboratory test rig to the same road input. In order to ensure that only the effects of the variation of the vehicle parameters are captured, a time domain drive signal for a kerb strike road event on the physical vehicle is generated from the proving ground data collected during durability testing of the vehicle.

This research proposes the use of Artificial Neural Networks (ANN) to predict the road input for road load data generation for variants of a vehicle as vehicle parameters are modified. This is important to the design engineers while the vehicle variant is still in the initial stages of development, hence no prototypes are available and accurate proving ground data acquisition is not possible. ANNs are, with adequate training, capable of representing the complex relationships between inputs and outputs. This research explores the implementation of the ANN to predict road input for vehicle variants using a quarter vehicle test rig. The training and testing data for this research are collected from a validated quarter vehicle model.

There is an increasing recognition of injector deposit (ID) formation in fuel injection equipment as direct injection spark ignition (DISI) engine technologies advance to meet increasingly stringent emission legislation and fuel economy requirements. While it is known that the phenomena of ID in DISI engines can be influenced by changes in fuel composition, including increasing usage of aliphatic alcohols and additive chemistries to enhance fuel performance, there is however still a great deal of uncertainty regarding the physical and chemical structure of these deposits, and the mechanisms of deposit formation. In this study, a mechanical cracking sample preparation technique was developed to assess the deposits across DISI injectors fuelled with gasoline and blends of 85% ethanol (E85).

In the development of a more accurate laboratory scale method, the ability to replicate the thermal oxidative degradation mechanisms seen in gas turbine lubricants, is an essential requirement. This work describes an investigation into the influence of key reaction parameters and the equipment set up upon extent and mechanism of oil degradation. The air flow rate through the equipment was found to be critical to both degradation rate and extent of volatilization loss from the system. As these volatile species can participate in further reactions, it is important that the extent to which they are allowed to leave the test system is matched, where possible, to the conditions in the gas turbine. The presence of metal specimens was shown to have a small influence on the rate of degradation of the lubricant. Loss of metal from the copper and silver specimens due to the mild corrosive effect of the lubricant was seen.

This paper presents an overview of the results on light duty vehicles collected in the “PARTICULATES” project which aimed at the characterization of exhaust particle emissions from road vehicles. A novel measurement protocol, developed to promote the production of nucleation mode particles over transient cycles, has been successfully employed in several labs to evaluate a wide range of particulate properties with a range of light duty vehicles and fuels. The measured properties included particle number, with focus separately on nucleation mode and solid particles, particle active surface and total mass. The vehicle sample consisted of 22 cars, including conventional diesels, particle filter equipped diesels, port fuel injected and direct injection spark ignition cars. Four diesel and three gasoline fuels were used, mainly differentiated with respect to their sulfur content which was ranging from 300 to below 10 mg/kg.

A field problem associated with flakes of combustion chamber deposits getting trapped on the exhaust valve seat and causing starting problems has appeared recently. Four fuels have been tested in three different car models using a deposit flaking road test procedure. For each piston top, flaking can be characterised using T1 and T2, the mean deposit thickness on the piston crown before and after flaking respectively. A new measure of deposit flaking, ΔT, the mean of (T1-T2) averaged over all cylinders has been introduced and its variance established for the standard test using one of the models. ΔT quantifies the actual amount of deposits that have flaked and is likely to be a more relevant indicator of flaking for startability problems than Rw, the mean of the ratio of T2 to T1, used in previous work. Deposit flaking is directly related to an increase in valve leakage rates and startability problems.

Biodegradable hydraulic fluids have been introduced relatively recently and, initially, acceptable environmental performance and technical performance were neither well specified or controlled. Over the past few years, many standards and specifications have been written, especially in the area of biodegradability and ecotoxicity. Technical performance test requirements are emerging more slowly, however, and there is still some doubt over appropriate tests and limits for some performance areas. The proliferation of standards is confusing to both the product developer and fluid user. This paper summarizes the common biodegradability and ecotoxicity elements in the main environmental performance standards. It also discusses appropriate laboratory performance tests for oxidation stability, hydrolytic stability and wear, and sets acceptable limits in these tests, based on correlation of lab and field performance of two synthetic ester based hydraulic fluids.

Fuel volatility and vehicle characteristics have long been recognised as important parameters influencing the exhaust emissions and the driveability of gasoline vehicles. Limits on volatility are specified in a number of world-wide / national fuel specifications and, in addition, many Oil Companies monitor driveability performance to ensure customer satisfaction. However, the relationship between driveability and exhaust emissions is relatively little explored. A study was carried out to simultaneously measure driveability and exhaust emissions in a fleet of 10 European gasoline vehicles. The vehicles were all equipped with three-way catalysts and single or multi-point fuel injection. The test procedure and driving cycle used were based on the European Cold Weather Driveability test method.

This paper presents the findings of theoretical and practical studies of an exhaust-gas reforming process, as applied to hydrocarbon fuels. It is shown that hydrogen-containing gaseous reformed fuels can be produced by the interaction of hot combustion products and an n-heptane feedstock in a small-scale catalytic reforming reactor. Predicted and observed reformed fuel chemical compositions were found to correlate well at the lower reactor space velocities tested, where chemical equilibrium conditions can be closely approached. Under these conditions, respective hydrogen and carbon monoxide yields of around 32 and 20 volume per cent were obtained. Under certain conditions, it was found that carbon solids were deposited on the reforming catalyst. Measures taken to avoid this problem included changes in the reforming oxidant to fuel ratio, and the addition of excess steam to the oxidant composition.