Search Results

In response to global climate change, there is a widespread push to reduce carbon emissions in the transportation sector. For the difficult to decarbonize heavy-duty (HD) vehicle sector, lower carbon intensity fuels can offer a low-cost, near-term solution for CO2 reduction. The use of natural gas can provide such an alternative for HD vehicles while the increasing availability of renewable natural gas affords the opportunity for much deeper reductions in net-CO2 emissions. With this in consideration, the US National Renewable Energy Laboratory launched the Natural Gas Vehicle Research and Development Project to stimulate advancements in technology and availability of natural gas vehicles. As part of this program, Southwest Research Institute developed a hybrid-electric medium-HD vehicle (class 6) to demonstrate a substantial CO2 reduction over the baseline diesel vehicle and ultra-low NOx emissions.

In this study, engine-out gaseous emissions are reviewed using the Fourier Transform Infrared (FTIR) spectroscopy measurement of methanol diesel dual fuel combustion experiments performed in a heavy-duty diesel engine. Comparison to the baseline diesel-only condition shows that methanol-diesel dual fuel combustion leads to higher regulated carbon monoxide (CO) emissions and unburned hydrocarbons (UHC). However, NOX emissions were reduced effectively with increasing methanol substitution rate (MSR). Under dual-fuel operation with methanol, emissions of nitrogen oxides (NOX), including nitric oxide (NO), nitrogen dioxide (NO2), and nitrous oxide (N2O), indicate the potential to reduce the burden of NOX on diesel after-treatment devices such as selective catalytic reduction (SCR).

The widely accepted best practice for spark-ignition combustion is the four-valve pent-roof chamber using a central sparkplug and incorporating tumble flow during the intake event. The bulk tumble flow readily breaks up during the compression stroke to fine-scale turbulent kinetic energy desired for rapid, robust combustion. The natural gas engines used in medium- and heavy-truck applications would benefit from a similar, high-tumble pent-roof combustion chamber. However, these engines are invariably derived from their higher-volume diesel counterparts, and the production volumes are insufficient to justify the amount of modification required to incorporate a pent-roof system. The objective of this multi-dimensional computational study was to develop a combustion chamber addressing the objectives of a pent-roof chamber while maintaining the flat firedeck and vertical valve orientation of the diesel engine.

According to the Annual Energy Outlook 2022 (AEO2022) report, almost 30% of the transport sector will still use internal combustion engines (ICE) until 2050. The transportation sector has been actively seeking different methods to reduce the CO2 emissions footprint of fossil fuels. The use of lower carbon-intensity fuels such as Renewable Diesel (RD) can enable a pathway to decarbonize the transport industry. This suggests the need for experimental or advanced numerical studies of RD to gain an understanding of its combustion and emissions performance. This work presents a numerical modeling approach to study the combustion and emissions of RD. The numerical model utilized the development of a reduced chemical kinetic mechanism for RD’s fuel chemistry. The final reduced mechanism for RD consists of 139 species and 721 reactions, which significantly shortened the computational time from using the detailed mechanism.

Conventional diesel combustion (CDC) is known to provide high efficiency and reliable engine performance, but often associated with high particulate matter (PM) and nitrogen oxides (NOX) emissions. Combustion of fossil diesel fuel also produces carbon dioxide (CO2), which acts as a harmful greenhouse gas (GHG). Renewable and low-carbon fuels such as renewable diesel (RD) and methanol can play an important role in reducing harmful criteria and CO2 emissions into the atmosphere. This paper details an experimental study using a single-cylinder research engine operated under dual-fuel combustion using methanol and RD. Various engine operating strategies were used to achieve diesel-like fuel efficiency. Measurements of engine-out emissions and in-cylinder pressure were taken at test conditions including low-load and high-load operating points.

Alternative fuels such as methanol can significantly reduce greenhouse gas (GHG) emissions when used in internal combustion engines (ICEs). This study characterized the combustion of methanol, methanol/diesel, and methanol/renewable diesel numerically. Numerical findings were also compared with engine experiments using a single-cylinder engine (SCE). The engine was operated under a dual-fuel combustion mode: methanol was fumigated at the intake port, and diesel was injected inside the cylinder. The characteristic of ignition delay trend as methanol concentration increased is being described at low temperature (low engine load) and high temperature (high engine load) conditions.

As an alternative fuel, renewable diesel (RD) could improve the performance of conventional internal combustion engines (ICE) because of its difference in fuel properties. With almost no aromatic content in the fuel, RD produces less soot emissions than diesel. The higher cetane number (CN) of RD also promotes ignition of the fuel, which is critical, especially under low load, and low reactivity conditions. This study tested RD fuel in a heavy-duty single-cylinder engine (SCE) under compression-ignition (CI) operation. Test condition includes low and high load points with change in exhaust gas recirculation (EGR) and start of injection (SOI). Measurements and analysis are provided to study combustion and emissions, including particulate matters (PM) mass and particle number (PN). It was found that while the combustion of RD and diesel are very similar, PM and PN emissions of RD were reduced substantially compared to diesel.

A physics-based spark ignition model was developed and integrated into a commercial CFD code. The model predicted the spark discharge process based on the electrical parameters of the secondary ignition circuit, tracked the spark motion as it was stretched by in-cylinder gas motion, and determined the resulting energy deposition to the gas. In concert with the existing kinetic solver in the CFD code, the resulting ignition and flame propagation processes were simulated. The model results have been validated against both imaging rig experiments of the spark in moving air and against engine experimental data. The model was able to replicate the key features of the spark and to capture the cyclic variability of high-dilution combustion when multiple engine cycles were simulated.

The automotive sector is rapidly transitioning to decarbonized, electric vehicles solutions. However, due to challenges with such rapid adoption, Internal combustion engines (ICE) are expected to be used for decades to come. In this transition period it is important to continue to improve ICE efficiency. A key design parameter to increase ICE efficiency is the compression ratio. For gasoline engines, the compression ratio is limited so as to avoid knock. Engine designers can employ several strategies to mitigate knock and enable higher compression ratios. In this study, a new methodology has been developed to compare various knock mitigation strategies. By comparing the knock limited load at a given combustion phasing the expected compression ratio increase can be inferred.

Simulating high amounts of exhaust gas recirculation in spark ignited engines to predict combustion using the currently available CFD modeling approaches is a challenge and does not always give reasonable matches with experimental observations. One of the reasons for the mismatch lies with the secondary circuit treatment of the ignition coil and the resulting energy deposition or a complete lack of it thereof. An ignition modeling approach is developed in this work which predicts the energy transfer from the electrical circuit to the gases in the combustion chamber leading to flame kernel growth under high EGR and high gas flow velocity conditions. Secondary circuit sub-model includes secondary side of the coil, spark plug and spark gap. The sub-model calculates the delivered energy to the gas based on given circuit properties and total initial electrical energy.

The worldwide trend of tightening CO2 emissions standards and desire for near zero emissions is driving development of high efficiency natural gas engines for a low CO2 replacement of traditional diesel engines. A Cummins Westport ISX12 G was previously converted to a Dedicated EGR® (D-EGR®) configuration with two out of the six cylinders acting as the EGR producing cylinders. Using a systems approach, the combustion and turbocharging systems were optimized for improved efficiency while maintaining the potential for achieving 0.02 g/bhp-hr NOX standards. A prototype variable nozzle turbocharger was selected to maintain the stock torque curve. The EGR delivery method enabled a reduction in pre-turbine pressure as the turbine was not required to be undersized to drive EGR. A high energy Dual Coil Offset (DCO®) ignition system was utilized to maintain stable combustion with increased EGR rates.

Southwest Research Institute (SwRI) converted a Cummins ISX 12 G in-line six-cylinder engine to a Dedicated EGRTM (D-EGRTM) configuration. D-EGR is an efficient way to produce reformate and increase the EGR rate. Two of the six cylinders were utilized as the dedicated cylinders. This supplied a nominal EGR rate of 33% compared to the baseline engine utilizing 15-20% EGR. PFI injectors were added to dedicated cylinders to supply the extra fuel required for reformation. The engine was tested with a high energy dual coil offset (DCO®) ignition system. The stock engine was tested at over 70 points to map the performance, 13 of these points were at RMC SET points. The D-EGR converted engine was tested at the RMC SET points for comparison to the baseline. The initial results from the D-EGR conversion show a 4% relative BTE improvement compared to the baseline due to the increased EGR rate at 1270 rpm, 16 bar BMEP.

Present day natural gas engines have a significant efficiency disadvantage but benefit with low carbon-dioxide emissions and cheap three-way catalysis aftertreatment. The aim of this work is to improve the efficiency of a natural gas engine on par with a diesel engine. A Cummins-Westport ISX12-G (diesel) engine is used for the study. A baseline model is validated in three-dimensional Computational Fluid Dynamics (CFD). The challenge of this project is adapting the diesel engine for the natural gas fuel, so that the increased squish area of the diesel engine piston can be used to accomplish faster natural gas burn rates. A further increase efficiency is achieved by switching to D-EGR technology. D-EGR is a concept where one or more cylinders are run with excess fueling and its exhaust stream, containing H2 and CO, is cooled and fed into the intake stream. With D-EGR although there is an in-cylinder presence of a reactive H2-CO reformate, there is also higher levels of dilution.

As the efforts to push capabilities of current engine hardware to their durability limits increases, more accurate and reliable analysis is necessary to ensure that designs are robust. This paper evaluates a method of Conjugate Heat Transfer (CHT) analysis for a gasoline and a diesel engine that combines combustion Computational Fluid Dynamics (CFD), engine Finite Element Analysis (FEA), and cooling jacket CFD with the goal of obtaining more accurate temperature distribution and heat loss predictions in an engine compared to standard de-coupled CFD and FEA analysis methods. This novel CHT technique was successfully applied to a 2.5 liter GM LHU gasoline engine at 3000 rpm and a 15.0 liter Cummins ISX heavy duty diesel engine operating at 1250 rpm. Combustion CFD simulations results for the gasoline and diesel engines are validated with the experimental data for cylinder pressure and heat release rate.

Diesel engines are facing increased competition from gasoline engines in the light-duty and small non-road segments, primarily due to the high relative cost of emissions control systems for lean-burn diesel engines. Advancements in gasoline engine technology have decreased the operating cost advantage of diesels and the relatively high initial-cost disadvantage is now too large to sustain a strong business position. SwRI has focused several years of research efforts toward enabling diesel engine combustion systems to operate at stoichiometric conditions, which allows the application of a low-cost three-way catalyst emission control system which has been well developed for gasoline spark-ignited engines. One of the main barriers of this combustion concept is the result of high smoke emissions from poor fuel/air mixing.

The influence of nozzle geometry on spray and combustion of diesel continues to be a topic of great research interest. One area of promise, injector nozzles with micro-holes (i.e. down to 30 μm), still need further investigation. Reduction of nozzle orifice diameter and increased fuel injection pressure typically promotes air entrainment near-nozzle during start of injection. This leads to better premixing and consequently leaner combustion, hence lowering the formation of soot. Advances in numerical simulation have made it possible to study the effect of different nozzle diameters on the spray and combustion in great detail. In this study, a baseline model was developed for investigating the spray and combustion of diesel fuel at the Spray A condition (nozzle diameter of 90 μm) from the Engine Combustion Network (ECN) community.

Recently conducted work has been funded by the California Air Resources Board (CARB) to explore the feasibility of achieving 0.02 g/bhp-hr NOX emissions for heavy-duty on-road engines. In addition to NOX emissions, greenhouse gas (GHG), CO2 and methane emissions regulations from heavy-duty engines are also becoming more stringent. To achieve low cold-start NOX and methane emissions, the exhaust aftertreatment must be brought up to temperature quickly while keeping proper air-fuel ratio control; however, a balance between catalyst light-off and fuel penalty must be addressed to meet future CO2 emissions regulations. This paper details the work executed to improve catalyst light-off for a natural gas engine with a close-coupled and an underfloor three-way-catalyst while meeting an FTP NOX emission target of 0.02 g/bhp-hr and minimizing any fuel penalty.

The primary focus of this investigation was to determine the hydrogen reformation, efficiency and knock mitigation benefits of methanol-fueled Dedicated EGR (D-EGR®) operation, when compared to other EGR types. A 2.0 L turbocharged port fuel injected engine was operated with internal EGR, high-pressure loop (HPL) EGR and D-EGR configurations. The internal, HPL-EGR, and D-EGR configurations were operated on neat methanol to demonstrate the relative benefit of D-EGR over other EGR types. The D-EGR configuration was also tested on high octane gasoline to highlight the differences to methanol. An additional sub-task of the work was to investigate the combustion response of these configurations. Methanol did not increase its H2 yield for a given D-EGR cylinder equivalence ratio, even though the H:C ratio of methanol is over twice typical gasoline.

It is projected that even when the entire on-road fleet of heavy-duty vehicles operating in California is compliant with 2010 emission standards of 0.20 g/bhp-hr, the National Ambient Air Quality Standards (NAAQS) requirements for ambient ozone will not be met. It is expected that further reductions in NOX emissions from the heavy-duty fleet will be required to achieve compliance with the ambient ozone requirement. To study the feasibility of further reductions, the California Air Resources Board (CARB) funded a research program to demonstrate the potential to reach 0.02 g/bhp-hr NOX emissions. This paper details the work executed to achieve this goal on the heavy-duty Federal Test Procedure (FTP) with a heavy-duty natural gas engine equipped with a three-way catalyst. A Cummins ISX-12G natural gas engine was modified and coupled with an advanced catalyst system.

The CO2 advantage coupled with the low NOX and PM potential of natural gas (NG) makes it well-suited for meeting future greenhouse gas (GHG) and NOX regulations for on-road medium and heavy-duty engines. However, because NG is mostly methane, reduced combustion efficiency associated with traditional NG fueling strategies can result in significant levels of methane emissions which offset the CO2 advantage due to reduced efficiency and the high global warming potential of methane. To address this issue, the unique co-direct injection capability of the Westport HPDI fuel system was leveraged to obtain a partially-premixed fuel charge by injecting NG during the compression stroke followed by diesel injection for ignition timing control. This combustion strategy, referred to as DI2, was found to improve thermal and combustion efficiencies over fumigated dual-fuel combustion modes.