Search Results

Ammonia (NH3) is a carbon-free fuel, which could partially or completely eliminate hydrocarbon (HC) fuel demand. Using ammonia directly as a fuel has some challenges due to its low burning speed and low flammability range, which generates unstable combustion inside the combustion chamber. This study investigated the effect of two different compression ratios (CRs) of 10.5 and 12.5 on the performance of ammonia combustion by using a conventional single spark-ignition (SI) approach. It was found that at a lower CR of 10.5, the combustion was unstable even at advanced spark timing (ST) due to poor combustion characteristics of ammonia. However, increasing the CR to 12.5 improved the engine performance significantly with lower cyclic variations. In addition, this research work also observed the effect of multiple spark ignition strategies on pure ammonia combustion and compared it with the conventional SI approach for the same operating conditions.

Hybrid powertrain has been proven to be an effective fuel-saving technology in commercial vehicles, but many hybrid commercial vehicles still use conventional diesel engines, resulting in limited fuel savings. The main purpose of this study is to enhance the thermal efficiency of a dedicated hybrid diesel engine focusing on the characteristic operating conditions. Via fundamental thermodynamics process analysis of internal combustion engine, steel piston with high compression ratio, air system involving two-stage turbocharger(2TC) with an intercooler, and late intake valve closing(IVC) timing are proposed to improve the thermal efficiency of the engine. Experimental results show that high compression ratio and lower thermal conductivity of the combustion chamber surface lead to lower heat release rates, requiring optimization of piston profile to accelerate the mixing rate. Besides, high compression ratio also leads to higher mechanical losses.

As a critical power source, the diesel engine is widely used in various situations. Diesel engine failure may lead to serious property losses and even accidents. Fault detection can improve the safety of diesel engines and reduce economic loss. Surface vibration signal is often used in non-disassembly fault diagnosis because of its convenient measurement and stability. This paper proposed a novel method for engine fault detection based on vibration signals using variational mode decomposition (VMD), K-means, and genetic algorithm. The mode number of VMD dramatically affects the accuracy of extracting signal components. Therefore, a method based on spectral energy distribution is proposed to determine the parameter, and the quadratic penalty term is optimized according to SNR. The results show that the optimized VMD can adaptively extract the vibration signal components of the diesel engine. In the actual fault diagnosis case, it is difficult to obtain the data with labels.

As the impacts of global warming have become increasingly severe, Oxy-Fuel Combustion (OFC) has been widely considered as a promising solution to reduce Carbon Dioxide (CO2) for achieving net-zero emissions. In this study, a one-dimensional simulation was carried out to study the implementation of OFC technology on a practical turbocharged 4-cylinder Gasoline Direct Injection (GDI) engine with economical oxygen-fuel ratios and commercial gasoline. When the engine is converted from Conventional Air-fuel Combustion (CAC) mode to OFC mode, and the throttle opening, oxygen mass fraction, stoichiometric air-fuel ratio (lambda = 1) are kept constant, it was demonstrated that compared to CAC mode, θF gets a remarkable extension whereas θC is hardly affected. θF and θC are very sensitive to the ignition timing, and Brake Specific Fuel Consumption (BSFC) would benefit significantly from applying Maximum Brake Torque (MBT) ignition timing.

Lean-burn combustion is an effective method for increasing the thermal efficiency of gasoline engines fueled with stoichiometric fuel-air mixture, but leads to an unacceptable level of high cyclic variability before reaching ultra-low nitrogen oxide (NOx) emissions emitted from conventional gasoline engines. Multi-point micro-flame ignited (MFI) hybrid combustion was proposed to overcome this problem, and can be can be grouped into double-peak type, ramp type and trapezoid type with very low frequency of appearance. This research investigates the micro-flame ignition stages of double-peak type and ramp type MFI combustion captured by high speed photography. The results show that large flame is formed by the fast propagation of multi-point flame occurring in the central zone of the cylinder in the double-peak type. However, the multiple flame sites occur around the cylinder, and then gradually propagate and form a large flame accelerated by the independent small flame in the ramp type.

Controlled Auto-Ignition (CAI) combustion can effectively improve the thermal efficiency of conventional spark ignition (SI) gasoline engines, due to shortened combustion processes caused by multi-point auto-ignition. However, its commercial application is limited by the difficulties in controlling ignition timing and violent heat release process at high loads. Stratified flame ignited (SFI) hybrid combustion, a concept in which rich mixture around spark plug is consumed by flame propagation after spark ignition and the unburned lean mixture closing to cylinder wall auto-ignites in the increasing in-cylinder temperature during flame propagation, was proposed to overcome these challenges.

Although supercharged system has been widely employed in downsized engines, the effect of supercharging on the intake flow characteristics remains inadequately understood. Therefore, it is worthwhile to investigate intake flow characteristics under high intake pressure. In this study, the supercharged intake flow is studied by experiment using steady flow test bench with supercharged system and transient flow simulation. For the steady flow condition, gas compressibility effect is found to significantly affect the flow coefficient (Cf), as Cf decreases with increasing intake pressure drop, if the compressibility effect is neglected in calculation by the typical evaluation method; while Cf has no significant change if the compressibility effect is included. Compared with the two methods, the deviation of the theoretical intake velocity and the density of the intake flow is the reason for Cf calculation error.

Lean NOx trap (LNT) is a great potential NOx abatement method for lean-burn gasoline engines in consideration of exhaust aftertreatment cost and installation space. NOx firstly is adsorbed on storage sites during the lean-burn period, then reduced to N2 under catalysis of the catalyst sites in the rich-burn phase. There must be a spillover of NOx species between both types of sites. For a better understanding of this spillover process of NOx species between Pt (as the catalytic center) and BaO sites (as storage components in commercial catalyst), this work focused on the vital first step of spillover, the adsorption of NOx on clean substrate surface (γ-Al2O3 (110) surface) and Ba\Pt cluster supported by the surface. Based on first principles software VASP (Vienna Ab-initio Simulation Package), the most stable adsorption structures of NO with Pt3 clusters and (BaO)3 clusters on carrier γ- Al2O3 (110) surface were confirmed and the adsorption energy of these structures were compared.

Noise source identification and separation of internal combustion engines is an effective tool for engine NVH (noise, vibration and harshness) development. Among various experimental approaches, noise source identification using signal processing has attracted extensive attention because of that the signal can be easily acquired and the requirements for equipment is relatively low. In this paper, variational mode decomposition (VMD) combined with independent component analysis (ICA) is used for noise source identification of a turbo-charged gasoline engine. Existing algorithms have been proved to be effective to extract signal features but also have disadvantages. One of the key problems in presently used method is that the main components of the signal, i.e. the main source of the noise, are unknown in advance. Thus the parameters selection of signal processing algorithms, which has a significance influence on the identification result, has no uniform criterion.

Two-stroke engines have to face the problems of insufficient charge for short intake time and the loss of intake air caused by long valve overlap. In order to promote the power of a two-stroke poppet valve diesel engine, measures are taken to help optimize intake port structure. In this work, the scavenging and combustion processes of three common types of intake ports including horizontal intake port (HIP), combined swirl intake port (CSIP) and reversed tumble intake port (RTIP) were studied and their characteristics are summarized based on three-dimensional simulation. Results show that the RTIP has better performance in scavenging process for larger intake air trapped in the cylinder. Its scavenging efficiency reaches 84.7%, which is 1.7% higher than the HIP and the trapping ratio of the RTIP reaches 72.3% due to less short-circuiting loss, 11.2% higher than the HIP.

As a major power source, diesel engines are being widely used in a variety of fields. However, because of complex structure, some faults which cannot be detected by direct signals would occur on engines and even lead to accidents. Among all kinds of indirect signals, vibration signal is the most common choice for faults detection without disassemble because of its convenience and stability. This paper proposed a novel approach for detecting multiple engine faults based on block vibration signals using variational mode decomposition (VMD) and echo state network (ESN). Since the quadratic penalty has a great influence on adaptable VMD that may make expected component signals cannot be extracted exactly, this paper proposed a dynamic quadratic penalty value, which will change with decomposing level. This paper selected a best dynamic quadratic penalty value by analyzing a large amount of data and results showed that this approach can decompose signals more exactly.

OH, soot and temperature distributions of wall-impinging diesel fuel spray were investigated in a high-temperature high-pressure constant volume combustion vessel. The ambient temperature (Ta) was set as 773 K, and the wall temperature (Tw) was set as 523 K, 673 K, 773 K, respectively. Three different injection pressures (Pi) of 60 MPa, 100 MPa, 160 MPa, and the ambient pressures (Pa) of 4 MPa were applied. The OH spatial distributions of wall-impinging spray were measured by the method of OH chemiluminescence imaging. Two-color pyrometry was applied to evaluate the spatial distributions of KL factor and flame temperature of wall-impinging spray. The results reveal that, OH chemiluminescence is observed in the region near the impingement point firstly. The regions of high OH chemiluminescence intensity and high KL factor appear in the location near the wall surface along the whole combustion process.

A new two-dimensional wall-flow DPF microstructure model has been developed in this paper to investigate the particle deposition distribution in DPF channels and the deep-bed filtration process of DPF. The substrate wall of the DPF having a thickness of L is divided into several layers with a uniform thickness of Δy along the cross-wall direction, and each layer has specific porosity and pore size. The pressure drop, particle deposition distribution and the dynamic deep-bed filtration process of the DPF with inhomogeneous wall structure are studied under various space velocities. Besides, the differences on DPF’s performance brought by the inhomogeneous wall structure are discussed by comparing with a homogeneous wall structure.

Controlled Auto-Ignition (CAI) combustion, also known as Homogeneous Charge Compression Ignition (HCCI), has the potential to simultaneously reduce the fuel consumption and nitrogen oxides emissions of gasoline engines. However, narrow operating region in loads and speeds is one of the challenges for the commercial application of CAI combustion to gasoline engines. Therefore, the extension of loads and speeds is an important prerequisite for the commercial application of CAI combustion. The effect of intake charge boosting, charge stratification and spark-assisted ignition on the operating range in CAI mode was reviewed. Stratified flame ignited (SFI) hybrid combustion is one form to achieve CAI combustion under the conditions of highly diluted mixture caused by the flame in the stratified mixture with the help of spark plug.

Controlled Auto-Ignition (CAI), also known as Homogeneous Charge Compression Ignition (HCCI), can improve the fuel economy of gasoline engines and simultaneously achieve ultra-low NOx emissions. However, the difficulty in combustion phasing control and violent combustion at high loads limit the commercial application of CAI combustion. To overcome these problems, stratified mixture, which is rich around the central spark plug and lean around the cylinder wall, is formed through port fuel injection and direct injection of gasoline. In this condition, rich mixture is consumed by flame propagation after spark ignition, while the unburned lean mixture auto-ignites due to the increased in-cylinder temperature during flame propagation, i.e., stratified flame ignited (SFI) hybrid combustion.

The potential of diesel/gasoline RCCI combustion coupled with late intake valve closing (LIVC) and double direct injection of diesel for meeting high fuel efficiency with ultra-low emissions was investigated in this study. The study was aiming at high load operation in a heavy-duty diesel engine. Based on the reactivity stratification of RCCI combustion, the employment of double injection of diesel fuel provided concentration stratification of the high-reactivity fuel, which is to further realize effective control of the combustion process. Meanwhile, late intake valve closing (LIVC) strategy is introduced to control the maximum in-cylinder pressure and nitrogen oxides (NOx) emissions.

The application of oxygen-enriched or oxy-fuel combustion coupled with carbon capture and storage technology has zero carbon dioxide emission potential in the boiler and gas turbine of the power plant. However, the oxygen-enriched combustion with high oxygen level has few studies in internal combustion engines. The fundamental issues and challenges of high oxygen level are the great differences in the physical properties and chemical effects compared with the combustion in air condition. As a consequence, the diesel spray combustion characteristics at high oxygen level were investigated in an optical constant volume vessel. The oxygen volume fraction of tested gas was from 21% to 70%, buffered with argon. The high-speed color camera was used to record the natural flame luminosity.

In order to improve the combustion and emissions for high-speed marine diesel engines, numerical investigations on effects of different combustion chamber structures combined with oxygen enriched air have to be conducted. The study uses AVL Fire code to establish three-dimensional combustion model and simulate the in-cylinder flow, air-fuel mixing and combustion process with the flow dynamics metrics such as swirl number and uniformity index, analyze the interactional effects of combustion chamber structures and oxygen enriched air against the experimental data for a part load operation at 1350 r/min, find the optimized way to improve engine performance as well as decrease the NOx and soot emissions. The novelty is that this study is to combine different oxygen concentration with different combustion chamber structures including the re-entrant chamber, the straight chamber and the open chamber.

In order to meet the increasingly stringent emissions restriction, it is indispensable to improve the combustion and emissions technology of high-speed marine diesel engines. Oxygen-enriched combustion and intake air humidification are effective ways to control pollution from diesel engines and improve combustion of diesel engines. In this study, the combustion and emission characteristics of supercharged intercooled marine diesel engine with humidity ratio and intake oxygen concentration were investigated by using multi-dimensional CFD model. The combustion model was established by AVL Fire code. The combination strategy of intake air humidification and oxygen-enriched combustion were optimized under partial load at 1350 rpm.

In order to achieve high-efficiency and clean combustion in HCCI engines, combustion must be controlled reasonably. A great variety of species with various reactivities can be produced through low temperature oxidation of fuels, which offers possible solutions to the problem of controlling in-cylinder mixture reactivity to accommodate changes in the operating conditions. In this work, in-cylinder combustion characteristics with low temperature reforming (LTR) were investigated in an optical engine fueled with low octane number fuel. LTR was achieved through low temperature oxidation of fuels in a reformer (flow reactor), and then LTR products (oxidation products) were fed into the engine to alter the charge reactivity. Primary Reference Fuels (blended fuel of n-heptane and iso-octane, PRFs) are often used to investigate the effects of octane number on combustion characteristics in engines.