Search Results

The effects of high boiling point fuel additives on deposits were investigated in a commercial turbocharged direct injection gasoline engine. It is known that high boiling point substances have a negative effect on deposits. The distillation end points of blended fuels containing these additives may be approximately 15°C higher than the base fuel (end point: 175°C). Three additives with boiling points between 190 and 196°C were examined: 4-tert-Butyltoluene (TBT), N-Methyl Aniline (NMA), and 2-Methyl-1,5-pentanediamine (MPD). Aromatics and anilines, which may be added to gasoline to increase its octane number, might have a negative effect on deposits. TBT has a benzene ring. NMA has a benzene ring and an amino group. MPD, which has no benzene ring and two amino groups, was selected for comparison with the former two additives.

The effects of Hydrotreated vegetable oil (HVO) on combustion and emission characteristics in a diesel engine were investigated by using spray analyzer, engine dynamometer and vehicle tests. Spray analysis showed that spray characteristics was virtually the same for HVO and diesel. From the results of the engine dynamometer and the vehicle tests, it was found that the high cetane number and the zero aromatics of HVO could reduce in HC and PM emissions. Moreover, as a result of optimized engine calcification, HVO is capable of improving partial fuel consumption and full-load torque. These results indicate that HVO has beneficial fuel characteristics for diesel engine.

In order to clarify the diesel fuel spray characteristics inside the cylinder, we developed two novel techniques, which are preparation of same level of temperature and pressure ambient as inside cylinder and quantitative measurement of vapor concentration. The first one utilizes combustion-type constant-volume chamber (inner volume 110cc), which allows 5 MPa and 873K by igniting the pre-mixture (n-pentane and air) with two spark plugs. In the second technique, TMPD vapor concentration is measured by using Laser Induced Exciplex Fluorescence method (LIEF). The concentration is compensated by investigation of the influence of ambient pressure (from 3 to 5 MPa) and temperature (from 550 to 900 K) on TMPD fluorescence intensity. By using two techniques, we investigated the influence of nozzle hole diameter, injection pressure and ambient condition on spray characteristics.

The higher compression ratio engines, two-stroke engines and flexible fuel vehicles currently under development tend to face the problems of spark plug fouling owing to the necessity of using cold type spark plugs. This paper analyzes the sparking of fouled spark plugs and investigates the characteristics required of an ignition system in order to avoid fouling problems. The results clearly establish that to maintain a strong spark even when the plug is fouled, a high voltage should be instantaneously applied to the spark plug. A series-gap on the high-tension side was confirmed to be an effective means of achieving this and a new plug cap provided with a series-gap has resolved fouling problems such as failure to start. Lately, fuel economy and long-term energy conservation have become critically important. For automobiles, higher compression ratio engines, two-stroke engines and flexible fuel vehicles (FFVs) are being developed.

The new generation engines currently being developed tend to require cold type spark plugs, which are prone to fouling. This paper describes the development of a new Coil on Plug ignition system that resolves this problem by using the high energy and the fast secondary voltage rise time of a capacitive ignition while maintaining inductive ignition characteristics for good ignitability. To evaluate the effectiveness of the system, spark plug insulation resistance was monitored and cold tests were conducted. The results demonstrated that the new ignition system is remarkably effective: insulation resistance remains high and startability and driveability are unaffected under conditions normally leading to excessive misfires and failure to start with a conventional inductive system. To satisfy environmental concerns, automobile manufactures are increasingly turning to high compression ratio engines in view of their improved performance.

For a Knock Control System (KCS) with a vibration sensor mounted on the engine block, means of improving the ratio of knock signal to engine vibration noise are discussed. From analyses of cylinder pressure and engine block vibration spectrums, it is shown that noise is lower in the second knock resonance frequency. The development of a resonance type knock sensor detecting this higher frequency is described. A new KCS utilizing this sensor is evaluated and found to improve knock controllability, especially in engines with a high compression ratio or supercharging.