Search Results

Engine starting vibration of hybrid vehicle with Toyota hybrid system has variations even in the same vehicle, and a large vibration that occurs rarely may cause stress to the passengers. The contribution analysis based on the vibration theory and statistical analysis has been done, but the primary factor of the rare large vibration has not been clarified because the number of factors is enormous. From this background, we apply machine learning that can reproduce multivariate and complicated relationships to analysis of variation factors of engine starting vibration. Variations in magnitude of the exciting force such as motor torque for starting the engine and in-cylinder pressure of the engine and timing of these forces are considered as factors of the variations. In addition, there are also nonlinear factors such as backlash of gears as a factor of variations.

In order to adapt to energy security and the changes of global-scale environment, further improvement of fuel economy and adaptation to each country’s severer exhaust gas emission regulation are required in an automotive engine. To achieve higher power performance with lower fuel consumption, the engine’s basic internal design such as an engine block and cylinder head were changed and the combustion speed was dramatically increased. Consequently, stroke-bore ratio and valve layout were optimized. Also, both flow coefficient and intake tumble ratio port were improved by adopting a laser cladded valve seat. In addition, several new technologies were adopted. The Atkinson cycle using a new Electrical VVT (Variable Valve Timing) and new combustion technology adopting new multi-hole type Direct fuel Injector (DI) improved engine power and fuel economy and reduced exhaust emissions.

As the demand for improved fuel economy increases and new CO2 regulations have been issued, aerodynamic drag reduction has become more critical. One of the important factors to consider is cooling drag. One way to reduce cooling drag is to decrease the air flow volume through the front grille, but this has an undesirable impact on cooling performance as well as component heat load in the under-hood area. For this reason, cooling drag reduction methods while keeping reliability, cooling performance and component heat management were investigated in this study. At first, air flow volume reduction at high speed was studied, where aerodynamic drag has the greatest influence. For vehicles sold in the USA, cooling specification tends to be determined based on low speed, while towing or driving up mountain roads, and therefore, there may be extra cooling capacity under high speed conditions.

The development of the Lexus LFA focused on the pursuit of a passionate driving experience suitable for a super sports car. The shift speed control system in the LFA is an automated manual transmission (AMT) that uses an electrohydraulic actuator. The excellent shifting performance of the AMT was achieved by developing control technology that performs smooth, quick, and highly responsive shifting in accordance with the driving conditions. This was the result of repeated evaluations in both normal driving and on circuits featuring many acceleration, deceleration, and high-speed driving sectors. This paper describes the AMT shift speed control system and technology.

Vehicles have been more required to save energy against the background of the tendency of ecology. As the result of improving efficiency of internal combustion engines and adoption of electric power train, heat loss from engine coolant, which is used to heat the cabin, decreases and consequently additional energy may be consumed to maintain thermal comfort in the passenger compartment in winter. This paper is concerned with the humidity control system that realizes reduction of ventilation heat loss by controlling recirculation rate of the HVAC system by using highly accurate humidity sensor to evaluate risk of fogging on the windshield. As the results of the control, fuel consumption of hybrid vehicles decreases and maximum range of electric vehicles increases.

The finite element method (FEM) is effective for analyzing brake squeal phenomena. Although FEM analysis can be used to easily obtain squeal frequencies and complex vibration modes, it is difficult to identify how to modify brake structure design or contact conditions between components. Therefore, this study deals with a practical design method using sensitivity analysis to reduce brake squeal, which is capable of optimizing both the structure of components and contact conditions. A series of analysis processes that consist of modal reduction, complex eigenvalue analysis, sensitivity analysis and optimization analysis is shown and some application results are described using disk brake systems.

TOYOTA has developed the world's first eight-speed automatic transmission (AA80E) for front-engine, rear-drive passenger cars. The AA80E developed for high-torque engines raises the level of power performance and fuel efficiency. To meet the size requirements needed for mounting in a passenger car application, an 8-speed geartrain, torque converter, transmission case and hydraulic control device were all newly-developed. Furthermore, the AA80E has benefited from technical developments to achieve an extremely high level of quietness and shifting performance. In this paper, the details of the AA80E are introduced.

In this paper, the authors have developed a new measuring method of the liquid fuel film thickness on walls, such as intake ports, the combustion chamber and cylinder liner of a Port Fuel Injection (PFI) engine, and clarified the fuel film behavior under various running conditions when Fiber-based Laser-Induced Fluorescence (Fiber-based LIF) was applied to the newly developed method. The thickness of the fuel film is measured by detecting the intensity of fluorescence from the film that is irradiated by a He-Cd laser. A single optical fiber is used to simultaneously transmit the laser beam and the fluorescence from the film. In addition, the S/N ratio of the fluorescence is improved by using a He-Cd laser of which the wavelength (λ=442nm) is able to efficiently irradiate test fuel doped 2-3-butandione. Using this method, the fuel film thickness on the wall of the PFI engine was analyzed in two case studies.

Reducing disk brake squeal, especially low frequency disk brake squeal (1-5kHz), is an important technical issue in vehicles. The disk brake squeal mechanism has been shown in many papers (1), (2), (3), (4), (5), (6), (7), (8) and (9). Recently, the disk brake squeal comes to be simulated by Finite Element Analysis (FEA) for disk brake design (10), (11), (12), (13), (14), (15), (16), (17), (18) and (19). Though FEA is useful, it is sometimes difficult to modify in large when the prototype of disk brake system has been designed. First Order Analysis gives design concepts, which should be done before FEA. This paper shows First Order Analysis of low frequency disk brake squeal. The equation of motion is shown in 4 degrees of freedom model. In this equation the generalized force matrix is composed of the variations of pressure and friction force between each brake pad and brake disk. The generalized force matrix is arranged with a symmetric matrix and an anti-symmetric matrix.

The tendency of spark ignition direct injection (SIDI) engines to form injector deposits was investigated using engine dynamometer tests on a SIDI engine equipped with fan spray type injectors. Fifteen test fuels with varying 90% distillation temperature (T90), aromatics, olefins, oxygenates and sulfur levels were prepared to identify the effects of fuel properties on injector deposits. The results suggested that not only the T90 but also the number of alkyl substituent of aromatics had effects on injector deposit formation. Effects of detergents on the injector deposit cleanliness were also evaluated in this study.

Numerical 3-D simulations are performed for the improvement of the new direct injection gasoline engine. A solution based local grid refinement method has been developed in order to reduce the CPU time. This method has been incorporated into the CFD program (STAR-CD) with in-house spray and combustion models. Calculation results were compared with the experimental data taken by the LIF technique, and good agreement was obtained for the mixture formation and combustion processes. Some calculations were carried out for the fuel-air mixture formation process during late injection stratified combustion and the following results were obtained. The unburnt fuel has a tendency to remain in the side of the piston cavity at the latter part of the combustion period. To reduce the amount of unburnt fuel, it was shown that the combination of a thin thickness fan spray and compact cavity forms a spherical mixture, suitable for combustion.

A method of fatigue life estimation for the spot-welds of vehicle body structures by means of Finite Element Analysis (FEA) was studied. 6 general forces applied to a nugget of spot-weld under multiaxial loads were determined and the Nominal Structural Stress (σns) was calculated from them. It was confirmed that fatigue strength of the spot-welds under various multiaxial loads could be estimated universally by using σns. Based on the theory of elasticity of plates, stress of spot-weld nugget was analyzed. The theoretical equations for determining the principal stress at the nugget edge from6 general forces acting on a nugget were derived. And the principal stress was defined as the σns. The value of σns was determined by FEM that used a solid model and compared with the theoretical calculation value. They agreed quite well. Fatigue tests of DC specimens under various multiaxial loads (shear plus cross tension and tensile shear plus torsion) were conducted.

In a stage of designing a CVJ boot, analytic conditions of FEA method are established so that values calculated with the FEA method coincide with the actually measured values. This has made it possible to predict the life of the boot under bench testing. Furthermore, the boot field life can also be predicted by the minor rule based on the joint-angle frequencies of a vehicle. As a result, it has become possible to determine an optimal configuration in the design stage and to decrease the number of test cycles, resulting in reduced development lead time.

One of the main types of window regulators that are in current use is the X-arm type window regulator, which utilizes a linkage mechanism to raise and lower the window glass. One of the evaluation items that are necessary in analyzing the performance of a window regulator is the operating force that is required to operate the handle for moving up the window glass. It is difficult to estimate this force during the design stage. We have to take into consideration factors such as the influences of the various types of contacts and the elastic deformation of linkage arm. Therefore, we used the LS-DYNA, which is dynamic and kinematic nonlinear finite element analysis code, to develop a technique for analyzing the handle operating force. Then, we used this technique to conduct parameter studies to identify the factors that are believed to exert a greater influence on the operating force.

Recently, use of aluminum engine parts has increased for fuel economy and power improvements. Aluminum cylinder heads, for example, are currently used in most engines. But, only low performance engine coolants are available for prevention of heat-transfer corrosion of aluminum cylinder heads. The authors have studied a laboratory test method that is able to accurately evaluate the performance of engine coolants for prevention of aluminum cylinder head corrosion. And we have developed the new test method by changing the test specimen temperature higher and the engine coolant temperature lower than the ASTM D4340 test. The new test has been confirmed engine bench test. We evaluated further the performance of many engine coolants of the world for prevention of aluminum cylinder head corrosion using the new test. We have known that there were a lot of poor performance engine coolants in the world.

A practical shape optimization technique is presented. We employed the basis vector method to parameterize the shape of the structural domain that is usually discretized by the finite element method. VMA/GENESIS software, the optimization system with finite element analysis, sensitivity analysis, and numerical optimization capabilities, was used for this study. Various design problems such as body, chassis, and engine parts design are solved to demonstrate the effectiveness and the robustness of the present approach for automotive applications.

Air flow around a car front end configuration and through the radiator and condenser was computed simultaneously. Although the engine compartment was simplified to reduce computational cost, comparison of experimental data with the analysis showed excellent prediction of the air flow through the radiator and condenser.

An experimental simulation method has been developed for predicting the noise and vibration characteristics of a complete vehicle when body frame stiffness is changed. This method was developed by means of an improved transfer function synthesis method. Advantages over numerical simulation methods, such as finite element analysis include dramatic reductions in computation time. This experimental method is also very easy to carry out with a few measurement data. By applying this method to investigate the effects of stiffness changes of different vehicle components on low frequency road noise, effective ways of reducing road noise were proposed in the first stage of vehicle development.

Concerns on environmental protection are being intensified throughout the world in recent years. Of those concerns, depletion of the ozone layer in the atomosphere caused by CFC emission into the atomosphere is the target of serious concern as shown in Fig. 1. At present, the use of CFC production is restricted by regulations at the global level, and CFC will be phased out by the end of 1995. In this regard, the authors have developed a new vehicle air conditioner to adapt to a new refrigerant HFC-134a, which is gentle to the ozone layer, and to replace CFC-12. The new refrigerant system was introduced to the market in October, 1991, and the replacement will be almost completed by the end of 1993 for the Lexus and Toyota production vehicles. This paper describes the development of the new compressor lubricant, seal rubber, hose and desiccant by taking into consideration the materials concerned and the number of technological issues involved in the new refrigerant, HFC-134a.

In order to achieve higher assembly accuracy for automotive body, increased body rigidity, and decreased stamping and assembly costs in car body manufacturing, a new method of sheet metal stamping has been developed, in which several blanks of different strength and thickness are integrated using CO2 laser-welding. The stamping formability of the laser-welded blank is limited compared with that of the conventional single blank. It is very difficult to predict the exact decrease in formability for different positions of the weld line and for different matching of materials. Because experimental estimations were indispensable for stamping die designers to evaluate formability at the stage of planning dies, many man-hours were spent conducting actual experiments.