Search Results

Fuel economy is one of the most important performance features for modern engine oils. For some time now, fuel efficient engine oils (called Energy Conserving II or EC-II) have been available in the marketplace. However, the performance of EC-II oils is only 2.7% Equivalent Fuel Economy Improvement (EFEI) as measured by the ASTM Sequence VI Engine Test. To meet future industry needs, more fuel efficient engine oils are desirable. In order to achieve this, a study of highly fuel efficient engine oils was initiated. An initial target of 3.9% EFEI was selected and several candidate oils were evaluated, some of which exceeded this target. The oils were evaluated using a chassis dynamometer using the U. S. EPA mode. The test results may be summarized: 5W-30 Prototype Oil containing MoDTC showed between 1.6 and 2.6% better fuel economy than conventional 5W-30 and 10W-30 EC-II oils. There was an optimum viscosity for maximum fuel economy using the EPA testing mode.

According to the principle of pH measurement, an on-board type engine oil deterioration sensor has been developed. The developed sensor is composed of a Pb and oxidized stainless steel electrodes. The sensor signal shows a good linear relationship to the quasi-pH value of the oil. Especially in the region where the oil deterioration proceeds, the remaining basic additives in the oil is easily estimated from the sensor signal.

Quality control of gasoline constituents and its effect on the Intake Valve Deposits (IVD) has become a recent issue. In this paper, the effects of gasoline and oil quality on intake valve deposits were investigated using an Intake Valve Deposit Test Bench and a Sludge Simulator. The deposit formation from the gasoline maximized at an intake valve temperature of approximately 160 °C, and the deposits formed from the engine oil were maximum at approximately 250 °C. Therefore, the contribution of the gasoline or the engine oil appears to depend on the engine conditions. The gasoline which contains MTBE or ethanol with no detergent additive slightly increases the deposition amount. The gasoline with a superior detergent significantly decreases the deposition amount even when MTBE or ethanol is blended in the gasoline. Appropriate detergent fuel additive retards the oil deterioration.

The effects of the phosphorus and sulfated ash contents of engine oils on the deactivation of monolithic three-way catalysts and oxygen sensors were studied. The effect of temperature was evaluated as well. The catalysts and oxygen sensors were poisoned in a 100-hour engine bench test. As a result, it was learned that engine oils with higher phosphorus contents showed a higher concentration of phosphorus on the catalyst surfaces, and the ability of the catalysts to convert carbon monoxide and oxides of nitrogen decreased. However, the phosphorus content was not observed to have any effect on hydrocarbons. The sulfated ash reduced the phosphorus concentration on the catalyst surface, but it also had a negative effect on the catalytic activity. The deactivation of the catalysts was much more noticeable at 800°C than at 720°C. In the tests at 720°C and 800°C, no deactivation of the oxygen sensors was observed, regardless of the composition of the engine oil.

Fifty percent distillation temperature (T50) can be used as a warm-up driveability indicator for a hydrocarbon-type gasoline. MTBE-blended gasoline, however, provides poorer driveability than a hydrocarbon-type gasoline with the same T50. The purposes of this paper are to examine the reason for poor engine driveability caused by MTBE-blended gasolines, and to propose a new driveability indicator for gasolines including MTBE-blended gasolines. The static and dynamic evaporation characteristics of MTBE-blended gasolines such as the evaporation rate and the behavior of each component during evaporation were analyzed mainly by using Gas Chromatography/Mass Spectrometry. The results of the analysis show that the MTBE concentration in the vapor, evaporated at ambient temperature (e.g. 24°C), is higher than that in the original gasoline. Accordingly, the fuel vapor with enriched MTBE flows into the combustion chamber of an engine just after the throttle valve is opened.

It has been reported that the middle range of gasoline distillation temperatures strongly affects vehicle driveability and exhaust hydrocarbon (HC) emissions, and that MTBE(CH3-O-C4H9)- blended gasoline causes poor driveability during warm-up. The present paper is concerned with the results of subsequent detailed research on gasoline characteristics, exhaust emissions and driveability. In this paper, first it is demonstrated by using four models of passenger cars having different types of exhaust gas treatment system that decreased 50% distillation temperature (T50) reduces exhaust HC emission. This result indicates lowering T50 in the market will contribute to improving air quality. Secondly gasoline behavior in the intake manifold is investigated by using an engine on the dynamometer in order to clarify the mechanisms of HC emission increase and poor engine response which are caused by high T50.