Search Results

Modern thermal propulsion systems (TPS) as part of hybrid powertrains are becoming increasingly complex. They have an increased number of components in comparison to traditionally powered vehicles leading to increased demand in packaging requirements. Many of the components in these systems relate to achieving efficiency gains, weight saving and pollutant reduction. This includes turbochargers and diesel or gasoline particulate filters for example and these are known to be very sensitive to inlet boundary conditions. When overcoming packaging requirements, sub-optimal flow distributions throughout the TPS can easily occur. Moreover, the individual components are often designed in isolation assuming relatively flat and artificially quiescent inlet flow conditions in comparison to those they are actually presented with. Thus, some of the efficiency benefits are lost through reduced component aerodynamic efficiency.

Resistive forces are a great source of fuel consumption in vehicles. In particular, rolling resistance represent the major resistance force at low speeds. It is highly influenced by the inflation pressure of the tire and vertical load over it. In the present work, a computer model is created with the objective of investigating the influence of tire inflation pressure on fuel consumption and rolling resistance force. Pressure is varied and parameters analyzed at different vehicle speeds for two different calculation methods. Results show significant decrease in fuel consumption and rolling resistance force as inflation pressure is augmented.

Reducing environmental pollution by the transport sector has been influenced according to the increasingly restrictions imposed by regulatory standards. For this, legislation such as Euro (at global level) and Proconve (at local level) set new limits each new phase, usually stipulating reductions in the levels of greenhouse gas emissions. Compliance with these requirements is seen with the vehicle or engine ratings working through the conditions imposed by a standard test cycle. However, standard driving conditions often do not represent the real-world driving conditions, being influenced by relief, traffic lights and other peculiarities of each city or route. This paper aims to compare real-world driving cycles of urban bus and passenger car in the city of Santa Maria, in southern Brazil, with the conditions used for light gasoline vehicles and heavy diesel vehicles approval.

The internal combustion engines require an efficient cooling system, the high temperatures generates at the time of combustion, reaching 2500 K peak burned gas. The materials used in the construction of the cylinder must operate within a maximum value, as well as the fluid film of lubricant oil. A bad dimensioned cooling system can lead to serious consequences such as loss of engine performance and/or efficiency, pre-ignition and increased exhaust emissions and may even lead to the destruction of the engine. In the torch ignition system overheating of the pre-chamber is even more critical and may lead to significant losses. Thus the torch ignition system requires an efficient cooling to prevent deterioration of the pre-chamber and consequently the engine caused by overheating. The solution proposed to resolve this inconvenience is the use of the cooling gallery in the cylinder head, for cooling the pre-chamber that is selected.

An torch ignition system with homogeneous charge is numerically analyzed using a one-dimensional computational model. The new ignition system is implemented in a four-cylinder engine, spark ignition, 1600 cm3, 16 valves. Parameters such as mass burn fraction profile and pressure vs crank angle are compared with experimental data obtained with the torch ignition system operating homogeneous charge with stoichiometric mixture. The computational model uses information such as the pre-chamber pressure as a function of crack angle, intake and exhaust pressure, volumetric efficiency, maps of injection and ignition, valve discharge and valve intake coefficient, lifting valve, laminar flame speed, among others parameters.

To attend the new tendencies of the automotive market, new technologies must be used throughout the engine conception. One way of improving the project is to use computational numerical simulation, predicting engine behavior in a wide range of situations. This paper presents a methodology to estimate the engine characteristic parameters necessary to numerical simulation. Morse test was used to determine friction power, mean effective pressure friction and friction torque, considering the engine behavior during cylinder ignition cut-off. In this test all the results were compatible with manufacturer data, which validates the methodology. To define the moment of inertia, it's also proposed a fuel cut methodology, associated with the Morse test, because the torque values measured by dynamometer after the fuel cut did not correspond to the real value. Thus, plausible values of engine moment of inertia, very close to values obtained by software, were obtained.

Driven by the necessity to reduce costs and improve products quality the automotive industry replaced the design method known as "trial and error" by those grounded on mathematical and physical theory. In this context, a longitudinal performance test was made by BAJA SAE UFMG team, in order to acquire vehicular performance data that will be used to validate computer models. The methodology consists of sensors and data acquisition system research, validation, fixation and installation in the vehicle, test and process of acquired data. From these steps, correlated data were acquired from magnitudes such as angular velocity in transmission shafts, global longitudinal acceleration and velocity, travel of break and throttle pedals and pressure inside of master cylinder. These results developed the knowledge about vehicular dynamic allowing the improvement of futures prototypes.

Computer simulations, dummy experiments with a new enhanced upper extremity, and small female cadaver experiments were used to analyze the small female upper extremity response under side air bag loading. After establishing the initial position, three tests were performed with the 5th percentile female hybrid III dummy, and six experiments with small female cadaver subjects. A new 5th percentile female enhanced upper extremity was developed for the dummy experiments that included a two-axis wrist load cell in addition to the existing six-axis load cells in both the forearm and humerus. Forearm pronation was also included in the new dummy upper extremity to increase the biofidelity of the interaction with the handgrip. Instrumentation for both the cadaver and dummy tests included accelerometers and magnetohydrodynamic angular rate sensors on the forearm, humerus, upper and lower spine.