Search Results

An investigation on the effect of dwell time of split injection on a diesel spray evolution and mixture formation process was carried out. A commercial 7-hole injector were used in the experiment to eliminate the possible discrepancies on the spray with single-hole research injector. Laser absorption scattering (LAS) technique was implemented for the measurement of the temporal evolution of fuel evaporation and mixture concentration. The diesel surrogate fuel consists of n-tridecane and 2.5% of 1-methylnaphthalene in volume basis was used. The total amount of fuel injected was initially fixed to 5.0 mg/hole. A split ratio of 9: 1 in mass basis was selected according to the results obtained from a previous study. The dwell time was varied from 120 µs to a negative value of −50 µs. The effects of negative dwell time was not ideal for lean mixture formation when compared to zero or positive dwell time conditions.

To get a better understanding of the characteristics of the high pressure gasoline sprays impinging on a wall, a fundamental study was conducted in a high-temperature high-pressure constant volume vessel under the simulated engine conditions of in-cylinder pressures, temperatures, and wall temperatures. The injection pressure was varied from 20 to 120 MPa. The spray tip penetration, vapor mass distribution, and vaporization rate were quantitatively measured with the laser absorption-scattering (LAS) technique. The velocity fields of the wall-impinging sprays under vaporizing conditions were measured with the particle image velocimetry (PIV) technique using silicone oil droplets as tracers. The effects of injection pressure and spray/wall interactions on spray characteristics were investigated. The results showed that the increased injection pressure improved penetration, vaporization, and turbulence of the sprays.

A comparison of spray characteristics was conducted between single- and multi-hole injectors. A commercial software (AVL FIRE) was used to investigate the internal flow inside the sac volume, as well as the initial spray behavior at 1 mm downstream of the nozzle exit. Microscopic imaging was applied to observe the spray dispersion angle (spray cone angle) at the vicinity of the nozzle. Laser absorption scattering (LAS) technique was implemented for measuring the mixture concentration. Three injection quantities, namely 0.5, 2.5, and 5.0 mg/hole, were selected to observe the differences between transient and quasi-steady spray. The vapor penetration at the initial stage of the injection was greater for single-hole than that of multi-hole injector due to faster fuel pressure build-up process inside the sac volume.

Spray combustion processes of palm oil biodiesel (PO) and conventional diesel fuels were simulated using the CONVERGE CFD code. Thermochemical and reaction kinetic data (115 species and 460 reactions) by Luo et al. (2012) and Lu et al. (2009) (68 species and 283 reactions) were implemented in the CONVERGE CFD to simulate the spray and combustion processes of the two fuels. Tetradecane (C14H30) and n- heptane (C7H16) were used as surrogates for diesel. For the palm biodiesel, the mixture of methyl decanoate (C11H20O2), methyl-9-decenoate (C11H19O2) and n-heptane was used as surrogate. The palm biodiesel surrogates were combined in proportions based on the previous GC-MS results for the five major biodiesel components namely methyl palmitate, methyl stearate, methyl oleate, methyl linoleate and methyl linolenate.

An early formation process of the spray, which was injected by a high-pressure swirl-type injector that is widely used in direct injection spark ignition (DISI) gasoline engines, was investigated through image analyzing techniques. The sprays were illuminated both by an Nd:YAG laser light sheet for getting the spray tomograms and by a tungsten lamp for getting the scattered back light shadow images of the sprays. The sprays were imaged by using a high-resolution CCD camera and a high-speed digital imaging system. The early development aspects of the spray were investigated in detail through the measurement of the tip penetration, cone angle and width of the early spray. At the start of injection, the liquid column emerges first, and it forms the “pre-swirl spray” without the swirl component. Following the liquid column, the liquid sheet emerges, however its radial velocity component is weak to form the complete hollow-cone spray. This spray changes into the “weak-swirl spray”.

A comprehensive model for sprays emerging from high-pressure swirl injectors in DISI engines has been developed accounting for both primary and secondary atomization. The model considers the transient behavior of the pre-spray and the steady-state behavior of the main spray. The pre-spray modeling is based on an empirical solid cone approach with varying cone angle. The main spray modeling is based on the Liquid Instability Sheet Atomization (LISA) approach, which is extended here to include the effects of swirl. Mie Scattering, LIF, PIV and Laser Droplet Size Analyzer techniques have been used to produce a set of experimental data for model validation. Both qualitative comparisons of the evolution of the spray structure, as well as quantitative comparisons of spray tip penetration and droplet sizes have been made. It is concluded that the model compares favorably with data under atmospheric conditions.

Experimental results of a diesel engine have shown that using split-injection can reduce the NOx and particulate emissions. For understanding the mechanism of emissions reduction, mixture formation in split-injection diesel sprays was characterized in the present paper. A dual-wavelength laser absorption-scattering (LAS) technique was developed by use of the second harmonic (532nm) and the fourth harmonic (266nm) of a pulsed Nd:YAG laser as the incident light and dimethylnaphthalene (DMN) as the test fuel. By applying this technique, imaging was made of DMN sprays injected into a high-temperature and high-pressure constant volume vessel by a single-hole nozzle incorporated in a common rail injection system for D.I. diesel engine. The line-of-sight optical thickness of both fuel vapor and droplets in the sprays was yielded from the sprays images.

An experimental study was conducted to investigate the flame propagation characteristics in the presence of a heterogeneous concentration distribution of a fuel-air mixture in order to provide fundamental knowledge of the effects of gaseous mixture concentration heterogeneity on the combustion process. Different propane-air mixture distributions were produced by the reciprocating movements of a pair of perforated plates in a constant volume combustion chamber. The mean equivalence ratio of the fuel-air mixture was varied from 0.7 on the lean side to 1.6 on the rich side, the turbulence intensity in the combustion chamber was also varied at levels of 0.185 m/s, 0.130 m/s, 0.100 m/s, and 0.0 m/s. By an independent control of the mixture distribution and the turbulence intensity in the combustion chamber, the flame structure and flame propagation speed at various heterogeneous levels of the mixture distribution were investigated in detail.

The internal flow of a diesel injection nozzle was studied by using transparent model nozzles to clarify the effects of the flows in the sac chamber and the discharge hole on the spray behaviors. The geometry of the model nozzle was scaled up 10 times the actual nozzle and the injection pressure for the model nozzle was adjusted so as to achieve a Reynolds number at the discharge hole which was the same as an actual nozzle. Aluminium oxide (Al2O3) tracers were used to visualize the flow patterns in the sac chamber. Sequential photographs of the internal flow and the issuing spray plume during the opening process of the needle valve were taken by a high-speed video camera. By locating the discharge hole on the upper side of the sac chamber, the turbulence intensity in the sac chamber increases and the spread angle of the spray plume becomes large.

This paper presents the experimental analysis for the turbulence in the combustion chamber of a direct injection (D.I.) diesel engine. A dual beam mode, forward-scattering laser doppler velocimeter was applied to the flow measurement in a four-stroke, single-cylinder direct injection diesel engine of 110 mm bore and 125 mm stroke. The turbulence component was separated from instantaneous velocity using a high-pass filter. As a result, the difference in turbulent intensity between the intake and compression processes was discussed. Also, the effect of intake port and piston cavity shapes, the compression ratio and the engine speed on the turbulent intensity were clarified. In addition, the empirical equation for the decay of turbulent intensity in the compression process was expressed by a function of the Reynolds number based on the mean swirling flow.

A mathematical model was developed for predicting the concentration of exhaust nitric oxide, soot and other emissions in a direct injection diesel engine. In the model, it was emphasized to describe the phenomena occurring in the combustion chamber from the microscopic point of view. The prediction was based on the knowledges concerning a single droplet as well as the droplet size distribution in a fuel spray and the spatial and temporal distribution histories of fuel in a combustion chamber. The heterogeneous field of temperature and equivalence ratio, and uniform pressure in the cylinder were postulated. The heat release model gives the burning rate of injected fuel and pressure and temperature history in the cylinder. The concentration of nitric oxide and soot in the cylinder was predicted by the emission formation model.