Search Results

Flow channels in proton exchange membrane fuel cells (PEMFC) play an irreplaceable role, and flow channel design in bipolar plates is one of the most active research areas at present. The flow channel on the cathode side needs to discharge liquid water out of the fuel cell in time and allow oxygen to flow to the cathode catalytic layer as much as possible to avoid the phenomenon of cathode water flooding and mass transfer loss. In order to improve the performance of PEMFC, a method of setting both side blockages in the cathode flow channel is proposed. In this paper, lateral blockage models with three shapes are proposed to study the influence of blockage on mass transfer and performance. First, a 3D PEMFC model with a middle channel was built to calculate the fuel cell power at different discharge rates.

Hydrogen recirculation system (HRS) is one of the main subsystems of proton exchange membrane fuel cell (PEMFC) system, and an HRS with high performance and low cost is essential to improve the fuel cell lifetime and efficiency. The ejector is becoming an effective alternative to the hydrogen circulation pump in the hydrogen recirculation system because of its small size, low cost and no parasitic power. However, the conventional ejector can only operate at the limited output power of the fuel cell. In order to improve this drawback, a hydrogen recirculation system with a separator-ejector integrated device is proposed. The hydrogen recirculation system based on the integrated device can make the space more compact, reduce the condensation effect of the piping, improve the fuel cell performance and reduce the cost. The design and integration method of the ejector and gas-water separator in this hydrogen recirculation system are introduced.

Knowledge about the health conditions and expected lifetime of an operating fuel cell stack is essential to system control and maintenance of a fuel cell vehicle. To quickly and accurately estimate a stack’s lifetime, a data-driven prediction model for proton exchange membrane fuel cells (PEMFCs) is proposed in this study. In this model, the voltage output of the fuel cell stack is taken as the lifetime evaluation index. Two methods are used to establish the lifetime decay evaluation criteria of the PEMFC stack, i.e., (1) Least Squares Fitting (LSF) method that establishes the standard for stack voltage degradation behavior, and (2) Back Propagation (BP) neural network that learns the stack’s voltage decay characteristics and establishes the standard for the stack’s voltage degradation behavior. The Autoregressive Moving Average (ARMA) time series model is then employed to learn part of the known decay behavior of stack voltage so as to predict future stack decay.

Butanol, which is a renewable biofuel, has been regarded as a promising alternative fuel for internal combustion engines. When blended with diesel and applied to pilot ignited natural gas engines, butanol has the capability to achieve lower emissions without sacrifice on thermal efficiency. However, high blend ratio of butanol is limited by its longer ignition delay caused by the higher latent heat and higher octane number, which restricts the improvement of emission characteristics. In this paper, the potential of increasing butanol blend ratio by adding hot exhaust gas recirculation (EGR) is investigated. 3D CFD model based on a detailed kinetic mechanism was built and validated by experimental results of natural gas engine ignited by diesel/butanol blends. The effects of hot EGR is then revealed by the simulation results of the combustion process, heat release traces and also the emissions under different diesel/butanol blend ratios.

To face the challenges of fossil fuel shortage and air pollution problems, there is growing interest in the potential usage of alternative fuels such as bio-ethanol and bio-butanol in internal combustion engines. The literature shows that the acetone in the Acetone-Butanol-Ethanol (ABE) blends plays an important part in improving the combustion performance and emissions, owing to its higher volatility. In order to study the effects of acetone addition into commercial gasoline, this study focuses on the differences in combustion, performance and emission characteristics of a port-injection spark-ignition engine fueled with pure gasoline (G100), ethanol-containing gasoline (E30) and acetone-ethanol-gasoline blends (AE30 at A:E volumetric ratio of 3:1). The tests were conducted at 1200RPM with the default calibration (for gasoline), at 3 bar and 5 bar BMEP under various equivalence ratios.

Recent research has shown that butanol, instead of ethanol, has the potential of introducing a more suitable blend in diesel engines. This is because butanol has properties similar to current transportation fuels in comparison to ethanol. However, the main downside is the high cost of the butanol production process. Acetone-butanol-ethanol (ABE) is an intermediate product of the fermentation process of butanol production. By eliminating the separation and purification processes, using ABE directly in diesel blends has the potential of greatly decreasing the overall cost for fuel production. This could lead to a vast commercial use of ABE-diesel blends on the market. Much research has been done in the past five years concerning spray and combustion processes of both neat ABE and ABE-diesel mixtures. Additionally, different compositions of ABE mixtures had been characterized with a similar experimental approach.

The paper analyzes the technological features of hydrogen fuel cell vehicles, describes the changes that hydrogen fuel cell vehicles will bring to the automobile industry and the marketing modes, and proposes a brand-new marketing mode of “automobile supermarket”. It also introduces the opportunities and challenges that fuel cell technology will bring to the world energy technology, and puts forward a concept of “hydrogen energy network” to push the mutual development of both hydrogen fuel cell vehicles and hydrogen energy industry.

A new type of dual fuel supply system has been developed. This system is able to economically convert conventional diesel engines into dual-fuel engines like LPG/Diesel engines and CNG/Diesel engines, which are capable of either using single diesel fuel or using dual-fuel including both diesel and CNG fuel or both diesel and LPG fuel. These diesel-LPG engines have been applied to the diesel buses in the public transportation of Guangzhou city, one of the biggest cities in China, owning to their low soot emissions, excellent operating performances and extremely low cost as well. Compared with the diesel baseline engine, it was found that there were a significant reduction in soot emission and an improvement of the fuel consumption with the diesel-LPG engine. Also the strategy on LPG content is discussed in order to meet the demands for soot emission, fuel economy, transient performance and output power at the same time.