Search Results

Previously, the authors have proposed a novel strategy called trajectory based combustion control for the free piston engine (FPE) where the shape of the piston trajectory between top and bottom dead centers is used as a control input to modulate the chemical kinetics of the fuel-air mixture inside the combustion chamber. It has been shown that in case of a hydraulic free piston engine (HFPE), using active motion control, the piston inside the combustion chamber can be forced to track any desired trajectory, despite the absence of a crankshaft, providing reliable starting and stable operation. This allows the use of optimized piston trajectory for every operating point which minimizes fuel consumption and emissions. In this work, this concept is extended to an electrical free piston engine (EFPE) as a modular power source.

Diesel particulate filter (DPF) technology has proven performance and reliability. However, the addition of a DPF adds significant cost and packaging constraints leading some manufacturers to design engines that reduce particulate matter in-cylinder. Such engines utilize high fuel injection pressure, moderate exhaust gas recirculation and modified injection timing to mitigate soot formation. This study examines such an engine designed to meet US EPA Interim Tier 4 standards for off-highway applications without a DPF. The engine was operated at four steady state modes and aerosol measurements were made using a two-stage, ejector dilution system with a scanning mobility particle sizer (SMPS) equipped with a catalytic stripper (CS) to differentiate semi-volatile versus solid components in the exhaust. Gaseous emissions were measured using an FTIR analyzer and particulate matter mass emissions were estimated using SMPS data and an assumed particle density function.

Diesel fuel injection systems are operating at increasingly higher pressure (up to 250 MPa) with smaller clearances, making them more sensitive to diesel fuel contaminants. Most liquid particle counters have difficulty detecting particles <4 μm in diameter and are unable to distinguish between solid and semi-solid materials. The low conductivity of diesel fuel limits the use of the Coulter counter. This raises the need for a new method to characterize small (<4 μm) fuel contaminants. We propose and evaluate an aerosolization method for characterizing solid particulate matter in diesel fuel that can detect particles as small as 0.5 μm. The particle sizing and concentration performance of the method were calibrated and validated by the use of seed particles added to filtered diesel fuel. A size dependent correction method was developed to account for the preferential atomization and subsequent aerosol conditioning processes to obtain the liquid-borne particle concentration.

The most recent goal of our research program was to identify the optimal features of each of three garments to maintain core temperature and comfort under intensive physical exertion. Four males and 2 females between the ages of 22 and 46 participated in this study. The garments evaluated were the MACS-Delphi, Russian Orlan, and NASA LCVG. Subjects were tested on different days in 2 different environmental chamber temperature/humidity conditions (24°C/H∼28%; 35°C/H∼20%). Each session consisted of stages of treadmill walking/running (250W to 700W at different stages) and rest. In general, the findings showed few consistent differences among the garments. The MACS-Delphi was better able to maintain subjects within a skin and core temperature comfort zone than was evident in the other garments as indicated by a lesser fluctuation in temperatures across physical exertion levels.

The focus of this work was the physical characterization of exhaust aerosol from the University of Minnesota Formula SAE team's engine. This was done using two competition fuels, 100 octane race fuel and E85. Three engine conditions were evaluated: 6000 RPM 75% throttle, 8000 RPM 50% throttle, and 8000 RPM 100% throttle. Dilute emissions were characterized using a Scanning Mobility Particle Sizer (SMPS) and a Condensation Particle Counter (CPC). E85 fuel produced more power and had lower particulate matter emissions at all test conditions, but more fuel was consumed.

The history of off-road equipment manufacturing has been based on proven designs and long times between model updates. In sharp contrast with this strategy is the electronic manufacturing services (EMS) industry. The EMS industry is driven by the larger consumer product industry's continuing pressure for lower costs. Because of this, EMS tools, processes, and practices have evolved to support rapid technology and component changes. However the increasing consumer demand for features like better user-interfaces, more efficient fuel consumption, and the desire for increased operational controls in equipment have forced the off-road industry to increase the frequency of product updates to meet customers' needs. Equipment manufacturers make running changes leading to a “Learning-by-doing” development and manufacturing process. But rapid changes sometimes have an unpredictable impact on the reliability of the final product.

Many engine exhaust emissions measurements require exhaust dilution. With low-emission engines, there is the possibility for contaminants in the dilution air to contribute artifacts to the emissions measurement. The objectives of this work are to discuss common methods used to clean the dilution air, to present the detailed analysis of a pressure swing adsorption (PSA) system and to compare the performance of the PSA with 2 other systems commonly used to provide dilution air for engine exhaust nanoparticle measurements. The results of the comparison are discussed in context with some emissions measurements that require exhaust dilution.

A one-stage dilution tunnel has been developed to sample and dilute diesel exhaust. The tunnel has the capability of simulating many aspects of the atmospheric dilution process. The dilution rate and overall dilution ratio, temperature, relative humidity, and residence time in the tunnel, as well as residence time and temperature in the transfer line between the tunnel and exhaust sampling point may be varied. In this work we studied the influence of the exhaust transfer line, tunnel residence time, and dilution air temperature on the exhaust particle size distribution. The influences of fuel sulfur content on the size distribution and on the sensitivity of the size distribution to dilution and sampling conditions were also examined. We do not suggest an optimum dilution scheme, but do identify critical variables.

Particle size distribution and number concentration measurements have been made in the diluted exhaust of a medium-duty, turbocharged, aftercooled, direct-injection Diesel engine using a unique variable residence time micro-dilution system that allows systematic variation of dilution and sampling conditions, and a scanning mobility particle sizer (SMPS). The measurements show that the number concentrations in the nanoparticle (Dp < 50 nm) and the ultrafine (Dp < 100 nm) ranges are very sensitive to dilution conditions and fuel sulfur content. Changes in concentration of up to two orders of magnitude have been observed when conditions are varied over the range that might be encountered in typical laboratory dilution systems. For example, at a dilution ratio of 12, dilution temperature of 32 °C, and a residence time of 1000 ms, the number concentrations reach 6 × 108 part.

The purpose of this study is to compare the dust loading behavior of ten filter media. The filters are used in engine air filtration, self-cleaning industrial air cleaners, building heating ventilation and cooling (HVAC), automotive cabin air filtration, air respirators, and general purpose air cleaning. Several types of filter media are tested. The filters include cellulose, synthetic (felt), glass, dual-layered glass/cellulose, mixed synthetic/glass, gradient packing glass, and electrically charged fibers. The initial pressure drops and fractional collection efficiencies as a function of particle size are reported. The filters were evaluated with two test dusts to investigate the size-dependent dust loading behavior. The two test dusts are SAE fine and submicron alumina powder (median diameter 0.25 μm). The results are analyzed and compared. It was found that the cellulose filters exhibited surface loading behavior and have the fastest growth of pressure drops.

The dust holding capacity of air cleaning filter depends on the size distribution of the particles. Traditional test dusts like Arizona road dust consist of a single mode of coarse particles. The purpose of this study is to evaluate the dust holding capacities of air filters with a bi-modal test dust that simulates the dust in atmospheric environments. The fine mode of the test dust consists of submicron Alumina particles that represent the fine particles in atmosphere. The coarse mode consists of traditional AC fine dust. The fine and coarse dusts are mixed in different mass ratios to simulate different atmospheric conditions. The ratios are 100% fine, 50%/50%, 25%/75%, 10%/90%, and 100% coarse. An engine air filter and a HVAC filter were studied with the bi-modal test dusts. The filter pressure drops were measured as a function of the dust loading. The results show that the flow resistance rises significantly faster as the ratio of fine to coarse fraction increases.

Two types of in-cylinder optical probes were applied to a single cylinder CFR engine to detect knocking combustion. The first probe was integrated directly into the engine spark plug to monitor the radiation from burned gas in the combustion process. The second was built into a steel body and installed near the end gas region of the combustion chamber. It measured the radiant emission from the end gas in which knock originates. The measurements were centered in the near infrared region because thermal radiation from the combustion products was believed to be the main source of radiation from a spark ignition engine. As a result, ordinary photo detectors can be applied to the system to reduce its cost and complexity. It was found that the measured luminous intensity was strongly dependent upon the location of the optical sensor.

Particulate emissions from heavy-duty buses were measured in real time under conditions encountered during the standard Central Business District (CBD) driving cycle. The buses tested were equipped with 1994 Detroit Diesel Engine Corporation 6V92-TA engines, and some included after treatment devices on the exhaust. Instantaneous, time-resolved measurements of CO2 and amorphous carbon concentrations were obtained using an optical extinction technique and compared to simultaneous results obtained using conventional dilution tunnel sampling methods. Good agreement was obtained between the real-time extinction measurements and the diluted CO2 and cycle-integrated filter measurements. The instantaneous measurements revealed that acceleration transients accounted for roughly 80% of the particulate mass emitted during the cycle but only about 45% of the fuel consumption.

As part of an ongoing program to control the emissions of diesel-powered equipment used in underground mines, the U. S. Bureau of Mines evaluated exhaust emissions from a compression ignition engine using oxygenated diesel fuels and a diesel oxidation catalyst (DOC). The fuels include neat (100%) soy methyl ester (SME), and a blend of 30% SME (by volume) with 70% petroleum diesel fuel. A Caterpillar 3304 PCNA engine was tested for approximately 50 hours on each fuel. Compared with commercial low-sulfur diesel fuel (D2), neat SME increased volatile organic diesel particulate matter (DPM) but greatly decreased non-volatile DPM, for a net decrease in total DPM. The DOC further reduced volatile and total DPM NOx emissions were slightly reduced for the case of neat SME, but otherwise were not significantly affected. Peak brake power decreased 9% and brake specific fuel consumption increased 13 to 14% for the neat methyl soyate because of its lower energy content compared with D2.

Results of comparisons of computed and measured soot and NO in a direct-injection Diesel engine are presented. The computations are carried out using a three-dimensional model for flows, sprays and combustion in Diesel engines. Autoignition of the Diesel spray is modeled using an equation for a progress variable which measures the local and instantaneous tendency of the fuel to autoignite. High temperature chemistry is modeled using a local chemical equilibrium model coupled to a combination of laminar kinetic and turbulent characteristic times. Soot formation is kinetically controlled and soot oxidation is represented by a model which has a combination of laminar kinetic and turbulent mixing times. Soot oxidation appears to be controlled near top-dead-center by mixing and by kinetics as the exhaust is approached. NO is modeled using the Zeldovich mechanism.

Results of three-dimensional computations of non-vaporizing and vaporizing Diesel sprays in a very high pressure (up to 18.4 MPa without combustion) environment are presented. These pressures and corresponding density ratios of ambient gas to injected liquid are about a factor of two greater than those in current Diesel engines. The spray model incorporates a line source for drops, heat, mass and momentum exchange between the gas and liquid phases, turbulent dispersion of drops, collisions and coalescences, and drop breakup. The accuracy of the model is assessed by making comparisons of computed and measured spray penetrations. Reasonable agreement is obtained for a broad range of conditions. A scaling for time and axial distance clarifies these results.

This paper quantifies typical United States in-vehicle cowl area particulate filter parameters such as temperature, humidity and environmental conditions. Secondly, United States and Germany particulate filter fleet results will be included to help quantify the effect of loading on electret nonwoven particulate filter fractional efficiency and demonstrate the amount and types of particulate matter captured. Finally the paper will address the low submicron fractional filter efficiency of a simulated production “wet and dry” plate-fin automotive evaporator core.

Previous studies have shown Late Intake Valve Closure (LIVC) through Variable Valve Timing (VVT) to offer reduced fuel consumption through reduced pumping work. Load modulation through the controlled phasing of one of two intake valves/cylinder is one means of accomplishing the LIVC strategy on a multi-valve engine. Experimental studies of LIVC show that cycle-to-cycle variations and reduced flame velocity in single or synchronized multiple intake valve engines are associated with performance which, though superior to throttled engine performance, falls short of its promised fuel economy. To examine if the higher mixture velocity promised by valve phasing relative to single or synchronized LIVC mitigates cycle-to-cycle variations and flame velocity defects, a modification of the Quad 4 engine has been designed and built and is, at the present writing, being tested. The design employs a third camshaft placed above the original intake valve camshaft.

Combustion characteristics of an L-head engine combustion chamber have been examined using ionization probes and piezioelectric pressure transducers. The method describes how pressure rise rates, peak pressures, mean effective pressures, and flame arrival times were recorded. The flame arrival times were then used to find the position and shape of the flame front as a function of time. The influence of spark plug location on the above parameters was then examined for two different combustion chamber shapes.