Search Results

There is a growing need for low-emissions concepts due to stricter emission regulations, more stringent homologation cycles, and the possibility of a ban on new engines by 2035. Of particular concern are the conditions during a cold start, when the Three-Way Catalyst is not yet heated to its light-off temperature. During this period, the catalyst remains inactive, thereby failing to convert pollutants. Reducing the time needed to reach this temperature is crucial to comply with the more stringent emissions standards. The post oxidation by means of secondary air injection, illustrated in this work, is a possible solution to reduce the time needed to reach the above-mentioned temperature. The strategy consists of injecting air into the exhaust manifold via secondary air injectors to oxidize unburned fuel that comes from a rich combustion within the cylinder.

Urban air mobility (UAM) is a fast-growing industry that utilizes electric vertical take-off and landing (eVTOL) technologies to operate in densely populated urban areas with limited space. However, atmospheric icing serves as a limitation to its operational envelope as in-flight icing can happen all year round anywhere around the globe. Since icing in smaller aviation systems is still an emerging topic, there is a necessity to study icing of eVTOL rotors specifically. Two rotor geometries were chosen for this study. A small 15-inch rotor was selected to illustrate a multirotor UAV drone, while a large 80-inch rotor was chosen to represent a UAM passenger aircraft. The ice accretion experiments were conducted in an icing wind tunnel on the small 15-inch rotor. The icing simulations were performed using FENSAP-ICE. The ice accretion simulations of the 15-inch rotor sections at –5 °C show a large, rather streamlined ice shape instead of the expected glaze ice characteristics.

Knocking is one of today’s main limitations in the ongoing efforts to increase efficiency and reduce emissions of spark-ignition engines. Especially for synthetic fuels or any alternative fuel type in general with a much steeper increase of the knock frequency at the KLSA, such as hydrogen, precise knock prediction is crucial to exploit their full potential. This paper therefore proposes a post-processing tool enabling further investigations to continuously gain better understanding of the knocking phenomenon. In this context, evaluation of local auto-ignitions preceding knock is crucial to improve knowledge about the stochastic occurrence of knock but also identify critical engine design to further optimize the geometry. In contrast to 0D simulations, 3D CFD simulations provide the possibility to investigate local parameters in the cylinder during the combustion.

In this paper, the differences between a production car of the 2018 A-class and an early stage vehicle model with a mostly similar outer skin are examined experimentally and numerically. The aerodynamic development of vehicles at Mercedes-Benz is divided into several phases. When comparing force coefficients differences can be observed between these distinct hardware stages as well as when comparing steady state simulations to wind tunnel measurements. In early phases when prototype vehicles are not yet available, so-called aero foam models are used. These are well-defined full-sized vehicle models, as the outer skin is milled from Polyurethane. Important aerodynamic characteristics such as a motor compartment with a cooling module, deflecting axles with rotatable wheels and underbody covers are represented.

The automotive industry uses supercharging in combination with various EGR strategies to meet the increasing demand for Diesel engines with high efficiency and low engine emissions. The charge air is heated by the EGR and the compression in the turbocharger to such an extent that high NOx emissions and a reduction in engine performance occurs. For this reason, the charge air cooler cools down the charge air before it enters the air intake manifold. In case of low pressure EGR, the charge air possesses a high moisture content and under certain operating conditions an accumulation of condensate takes place within the charge air cooler. During demanding engine loads, the condensate is entrained from the charge air cooler into the combustion chamber, resulting in misfiring or severe engine damage.

This paper investigates the pressure drop with and without condensation inside a charge air cooler. The background to this investigation is the fact that the stored condensate in charge air coolers can be torn into the combustion chamber during different driving states. This may result in misfiring or in the worst-case lead to an engine failure. In order to prevent or reduce the accumulated condensate inside charge air coolers, a better understanding of the detailed physics of this process is required. To this end, one single channel of the charge air side is investigated in detail by using an experimental setup that was built to reproduce the operating conditions leading to condensation. First, measurements of the pressure drop without condensation are conducted and a good agreement with experimental data of a comparable heat exchanger reported in Kays and London [1] is shown.

Further improvements of internal combustion engines to reduce fuel consumption and to face future legislation constraints are strictly related to the study of mixture formation. The reason for that is the desire to supply the engine with homogeneous charge, towards the direction of a global stoichiometric blend in the combustion chamber. Fuel evaporation and thus mixture quality mostly depend on injector atomization features and charge motion within the cylinder. 3D-CFD simulations offer great potential to study not only injector atomization quality but also the evaporation behavior. Nevertheless coupling optical measurements and simulations for injector analysis is an open discussion because of the large number of influencing parameters and interactions affecting the fuel injection’s reproducibility. For this purpose, detailed numerical investigations are used to describe the injection phenomena.

The industry is working intensively on the precision of thermal management. By using complex thermal management strategies, it is possible to make engine heat distribution more accurate and dynamic, thereby increasing efficiency. Significant efforts are made to improve the cooling efficiency of the engine water jacket by using 3D CFD. As well, 1D simulation plays a significant role in the design and analysis of the cooling system, especially for considering transient behaviour of the engine. In this work, a practice-oriented universal method for creating a 1D water jacket model is presented. The focus is on the discretization strategy of 3D geometry and the calculation of heat transfer using Nusselt correlations. The basis and reference are 3D CFD simulations of the water jacket. Guidelines for the water jacket discretization are proposed. The heat transfer calculation in the 1D-templates is based on Nusselt-correlations (Nu = Nu(Re, Pr)), which are derived from 3D CFD simulations.

For the gasoline engine, the isochoric process is the ideal limit of the ideal processes. During the project, a combustion engine with real isochoric boundary conditions is built. A “resting time” of the piston for several degrees crank angle in the top dead center (TDC) can be realized with a special crank drive. This crank drive consists of two crankshafts with different strokes, which are combined. The two crankshafts rotate with a ratio of two to one in opposite directions. The total stroke corresponds to the amount of the first crankshaft, so it is possible to investigate different strokes of the second crankshaft in the same crankcase. Different “resting times” can be achieved by different strokes of the second crankshaft. A specific combination of both crankshafts make a stroke possible which corresponds to that of a conventional combustion engine.

As a consequence of reduced fuel consumption, direct injection gasoline engines have already prevailed against port fuel injection. However, in-cylinder fuel homogenization strongly depends on charge motion and injection strategies and can be challenging due to the reduced available time for mixture formation. An insufficient homogenization has generally a negative impact on the combustion and therefore also on efficiency and emissions. In order to reach the targets of the intensified CO2 emission reduction, further increase in efficiency of SI engines is essential. In this connection, 0D/1D simulation is a fundamental tool due to its application area in an early stage of development and its relatively low computational costs. Certainly, inhomogeneities are still not considered in quasi dimensional combustion models because the prediction of mixture formation is not included in the state of the art 0D/1D simulation.

Engine valve flow coefficients are used to describe the flow throughput performance of engine valve/port designs, and to model gas exchange in 0D/1D engine simulation. Valve flow coefficients are normally determined at a stationary flow test bench, separately for intake and exhaust side, in the absence of the piston. However, engine operation differs from this setup; i. a. the piston might interact with valve flow around scavenging top dead center, and instead of steady boundary conditions, valve flow is nearly always subjected to pressure pulsations, due to pressure wave reflections within the gas exchange ports. In this work the influences of piston position and flow pulsation on valve flow coefficients are investigated for different SI engine geometries by means of 3D CFD and measurements at an enhanced flow test bench.

Engine valve flow coefficients are not only used to characterize the performance of valve/port designs, but also for modelling gas exchange in 0D/1D engine simulation. Flow coefficients are usually estimated with small pressure ratios and at ambient air conditions. In contrast, the ranges for pressure ratio, pressure and temperature level during engine operation are much more extensive. In this work the influences of these three parameters on SI engine poppet valve flow coefficients are investigated using 3D CFD and measurements for validation. While former investigations already showed some pressure ratio dependencies by measurement, here the use of 3D CFD allows a more comprehensive analysis and a deeper understanding of the relevant effects. At first, typical ranges for the three mentioned parameters during engine operation are presented.

The real cycle simulation is an important tool to predict the engine efficiency. To evaluate Extended Expansion SI-engines with a multi-link cranktrain, the challenge is to consider all concept specific effects as best as possible by using appropriate submodels. Due to the multi-link cranktrain, the choice of a suitable heat transfer model is of great importance since the cranktrain kinematics is changed. Therefore, the usage of the mean piston speed to calculate a heat-transfer-related velocity for heat transfer equations is not sufficient. The heat transfer equation according to Bargende combines for its calculation the actual piston speed with a simplified k-ε model. In this paper it is assessed, whether the Bargende model is valid for Extended Expansion engines. Therefore a single-cylinder engine is equipped with fast-response surface-thermocouples in the cylinder head. The surface heat flux is calculated by solving the unsteady heat conduction equation.

Longitudinal models are used to evaluate different vehicle-engine concepts with respect to driving behavior and emissions. The engine is generally map-based. An explicit calculation of both fluid dynamics inside the engine air path and cylinder combustion is not considered due to long computing times. Particularly for dynamic certification cycles (WLTC, US06 etc.), dynamic engine effects severely influence the quality of results. Hence, an evaluation of transient engine behavior with map-based engine models is restricted to a certain extent. The coupling of detailed 1D-engine models is an alternative, which rapidly increases the model computation time to approximately 300 times higher than that of real time. In many technical areas, the Fourier transformation (FT) method is applied, which makes it possible to represent superimposed oscillations by their sinusoidal harmonic oscillations of different orders.

As known de-icing methods use a high amount of energy or environmentally harmful chemicals, research has focused lately on passive de-icing by functional surfaces with an improved removal of ice (de-icing) or a reduced formation of it (anti-icing). Inspired by the Lotus plant leaf, a “superhydrophobic” surface can be produced by the combination of a hierarchical micro/nanoscale roughness and a hydrophobic surface coating. By a hot stamping process we have generated differently shaped microstructures (cylinders, ellipses) on polyurethane (PU) films which were afterwards coated by a plasma enhanced chemical vapor deposition (PECVD) process with thin, hydrophobic fluorocarbon films. This combination of methods could be a process for the production of large area functionalized films. PU films are suitable for outdoor use, because they are resistant against erosion and UV radiation. The films can be glued to different geometries and can easily be exchanged if damaged.

Multi-dimensional modelling of the flow and combustion promises to become a useful optimisation tool for IC engine design. Currently, the total simulation time for an engine cycle is measured in weeks to months, thus preventing the routine use of CFD in the design process. Here, we shall describe three tools aimed at reducing the simulation time to less than a week. The rapid template-based mesher produces the computational mesh within 1-2 days. The parallel flow solver STAR-CD performs the flow simulation on a similar time-scale. The package is completed with COVISEMP, a parallel post-processor which allows real-time interaction with the data.

The use of gas springs with a surge tank to generate blank holding forces in drawing tools is increasing. These gas spring systems are characterized by an almost constant behaviour of the spring force over the spring displacement. To prevent an increase of the normal pressure with increasing stroke in a drawing process, it is advantageous to obtain a degressive force-displacement behaviour of the gas springs. For this reason, a gas spring system was developed to realize a decrease of the blank holding forces over the stroke without large additional expenditure. The technical realization takes place in an exact controlling of the upper and lower pressure chamber of the nitrogen cylinder.

A two-dimensional technique for the quantitative determination of the fuel-air ratio in hydrogen fuelled engines has been developed. The technique is based on the spontaneous Raman scattering of the hydrogen molecules (Stokes Q-branch) and the simultaneous measurement of the pressure inside the combustion chamber. From these data the local partial pressure of the hydrogen and, therefore, the fuel-air ratio can be calculated. This method was applied in a single cylinder direct injection research engine in order to prove the applicability of this technique under real engine conditions. The measurements inside the side chamber of the engine show a fast mixing process of the compressed air and the injected hydrogen (6 MPa injection pressure) independent of the injection timing.

A numerical simulation program for the design of the cooling air duct and the cooling system of vehicles for stationary operating conditions is introduced. This program allows the simulation of interactions with the system environment resp. an air conditioning. Hot recirculations of air in the front part of the car and the inhomogenious flow through the heat exchangers radiator and condensor in their affects on the heat transfer capacity are simulated. The power demand of the fan, the water pump and the compressor is taken into account for calculating the heat flow from the engine into the cooling water.