Search Results

Accurate evaluation of vehicles' transient total power requirement helps achieving further improvements in vehicle fuel efficiency. When operated, the air-conditioning (A/C) system is the largest auxiliary load on a vehicle, therefore accurate evaluation of the load it places on the vehicle's engine and/or energy storage system is especially important. Vehicle simulation models, such as "Autonomie," have been used by OEMs to evaluate vehicles' energy performance. However, the load from the A/C system on the engine or on the energy storage system has not always been modeled in sufficient detail. A transient A/C simulation tool incorporated into vehicle simulation models would also provide a tool for developing more efficient A/C systems through a thorough consideration of the transient A/C system performance. The dynamic system simulation software MATLAB/Simulink® is frequently used by vehicle controls engineers to develop new and more efficient vehicle energy system controls.

As global automobile manufacturers prepare for the phase-out of R134a in Europe, they must address the issue of using the new refrigerant for European sales only or launching the product worldwide. Several factors play into this decision, including cost, service, risk, customer satisfaction, capacity, efficiency, etc. This research effort addresses the minimal vehicle-level hardware differences necessary to provide a European solution of R1234yf while continuing to install R134a into vehicles for the rest of the world. It is anticipated that the same compressor, lubricant and condenser; most fluid transport lines; and in most cases the evaporator can be common between the two systems.

The automotive aftermarket represents a challenge for supply chain management when compared to traditional practices in the original equipment manufacturer (OEM) supply chain. This paper presents a case study for a Tier One automotive supplier’s challenges with inventory carrying costs, backorder risk, and supplier relationships for a rear seat entertainment system in the automotive aftermarket. It will also address the lean principles used to improve the business and increase material planning analyst productivity. A call for OEMs to examine their business practices is also included.

First LED headlamps will be released into the market in 2007. Special permissions allow this introduction although the official regulation is still under discussion in ECE. The LED technology for front lighting has entered into a new phase from theoretical, prototype status to real and practical applications. Additionally in Europe the legislation, which is under preparation, defines LED modules with one or more LED chips in a row which should be replaceable. With this boundary conditions headlamp suppliers needs to balance between an attractive and innovative styling, demanded by car manufacturers and the light performance to gurantee good visibility at night. The paper describes the methods how to design an LED headlamp with high efficiency by keeping in mind the parameters: packaging, weight, styling and light perfromance. Results with specific design proposals are shown.

During last 10-15 years we could have seen quite big changes in automotive lighting. The most important changes are: a) plastic materials mostly removed metal and glass material from lighting products raised heat issue of plastics materials b) escalation of competition between lighting suppliers (globalization, merging, …) decrease of time and cost for development of the new product as much as possible

High-power LEDs and LED headlamps have become a serious consideration for the automotive industry. White LEDs have achieved the required performance for initial automotive headlamp applications. However tradeoffs among several attributes such as efficiency, cost, weight and performance profoundly affect LED headlamp development and need to be addressed by vehicle manufacturers, lamp set makers and LED source suppliers in order for LED headlamps to be effective. The solutions to these tradeoffs relates to the behavior of the LED sources, the thermo-mechanical integration of LEDs in a headlamp environment and input from the vehicle manufacturer regarding styling and packaging for an LED headlamp on the respective targeted vehicles.

Up to date, computer aided engineering (CAE) has been used in improvement of design quality and reduction of cost and delivery time. Although it has been widely accepted as a standard product development tool by the engineering community, CAE still faces many challenges in improving simulation process efficiency through process integration and automation, and simulation accuracy by analytical model/physical testing correlation. CAE engineers are constantly improving the accuracy of their analytical models through test correlation to deliver higher confidence for their analysis result. Although laboratory testing has provided an effective way to accelerate product development, analytical simulation of the lab test has been used frequently to further reduce the development cost and time throughout many industries. This paper presents a case study of CAE correlation of a finite element (FE) model of an automotive beam axle assembly in a laboratory test environment.

Computational Fluid Dynamics (CFD) is an integral part of product development at Visteon Climate Systems with a validated set of CFD tools for airflow and thermal management processes. As we increasingly build CAE capabilities to design not only thermal comfort, but quiet systems, developing noise prediction capabilities becomes a high priority. Two Broadband Noise Source (BNS) models will be presented, namely Proudman's model for quadrupole source and Curle's boundary layer model for dipole source. Both models are derived from Lighthill's acoustic analogy which is based on the Navier-Stokes equations. BNS models provide aeroacoustic tools that are effective in screening air handling systems with higher noise levels and identifying components or surfaces that generate most of the noise, hence providing opportunities for early design changes. In this paper, BNS models were used as aeroacoustic design tools to redesign an automotive HVAC center duct with high levels of NVH.

Virtual design validation of an air induction system (AIS) requires a proper finite element (FE) assembly model for various simulation based design tasks. The effect of the urethane air filter seal within an AIS assembly, however, still poses a technical challenge to the modeling of structural dynamic behaviors of the AIS product. In this paper, a filter seal model and its modeling approach for AIS assemblies are introduced, by utilizing the feature finite elements and empiric test data. A bushing element is used to model the unique nonlinear stiffness and damping properties of the urethane seal, as a function of seal orientation, preloading, temperature and excitation frequency, which are quantified based on the test data and empiric formula. Point mobility is used to character dynamic behaviors of an AIS structure under given loadings, as a transfer function in frequency domain.

Tuned mass dampers are frequently used in vehicles to resolve vibration issues arising from problematic torsional modes. The design of a tuned damper is straightforward, but evaluating its effect on other system modes is time consuming. An upfront design tool will accelerate the process of designing and evaluating the damper's affect on system level dynamic characteristics. Computer aided engineering tools have been developed to design a tuned torsional damper using two different approaches. In the first approach, a two-degree of freedom torsional system model is utilized. In the second approach, a detailed finite element model of a driveline system is considered. In the second approach, the effect of the damper to the vehicle driveline system response at the hypoid pinion nose and other desired locations is studied to assess the effectiveness of the damper design. In both approaches, the damper rotational inertia is considered as a design variable.

Determination of the critical speed of a driveshaft is critical for development and validation of its design for use in a vehicle because of its destructive effects. Typical calculations to determine critical speed are either over simplistic and not very accurate or very complicated requiring CAE software and capabilities. An analytical five-section non-prismatic beam model was developed to fill in this gap. The model was developed to compute the critical speed in a worksheet and proven to be as or more accurate as utilizing FEA methods. The model worksheet calculates the critical speed for one-piece conventional driveshafts and adapted for Visteon's Slip-In-Tube (SIT) driveshafts.

Occupant head impact simulations on automotive instrument panels (IP) are routinely performed as part of an integrated design process during the course of IP development. Based on the requirements (F/CMVSS, ECE), head impact zones on the IP are first established, which are then used to determine the various “hit” locations to be tested/analyzed. Once critical impact locations are identified, CAE simulations performed which is a repetitive process that involves computing impact angles, positioning the rigid head form with an assigned initial velocity and defining suitable contacts within the finite element model. A commercially available CAE process automation tool was used to automate these steps and generate a head impact simulation model. Once the input model is checked for errors by the automated process, it can be submitted to a solver without any user intervention for analysis and report generation.

An effort to integrate a structural optimization process into the carbon canister bracket design is presented to demonstrate the benefits of an upfront Computer-Aided Engineering (CAE) driven design. Structural optimization methods - including topology, shape, and size optimization - are used to develop the injection molded plastic carbon canister bracket. Furthermore, the incorporation of the Knowledge Base Engineering (KBE) features in the design process not only accelerates the design process but also ease manufacturing feasibility. Even though topology optimization has been widely used to explore the initial topological designs of different products, it is still a great challenge to explore shell like structure designs with 3D solid design package spaces using topology optimization method.

A coupled vibration and pressure loading procedure has been developed to perform a CAE virtual test for engine air intake manifolds. The CAE virtual test simulates the same physical test configuration and environments, such as the base acceleration vibration excitation and pressure pulsation loads, as well as temperature conditions, for design validation (DV) test of air intake manifolds. The original vibration and pressure load data, measured with respect to the engine speed rpm, are first converted to their respective vibration and pressure power spectrum density (PSD) profiles in frequency domain, based on the duty cycle specification. The final accelerated vibration excitation and pressure PSD load profiles for design validation are derived based on the key life test (KLT) duration and reliability requirements, using the equivalent fatigue damage technique.

Modern automobiles utilize stabilizer bars to increase vehicle roll stiffness. Stabilizer bars are laterally mounted torsional springs which resist vertical displacement of the wheels relative to one another. A stabilizer bar is constructed in such a way that it will meet package constraints and fatigue requirements. In order to design a robust stabilizer bar, Taguchi's “Design of Experiment method” is used. The objective of this paper is to develop a robust stabilizer bar design that will maximize the fatigue life and the roll stiffness while minimizing weight. This study is based on results obtained by CAE analysis.

A dynamic computer model of automotive air conditioning systems was developed. The model uses simulation software for the coding of 1-D heat transfer, thermodynamics, fluid flow, and control valves. The same software is used to model 3-D solid dynamics associated with mechanical mechanisms of the compressor. The dynamics of the entire AC system is thus simulated within the same software environment. The results will show the models potential applications in component and system design, calibration and control.

Evaporators for automotive air-conditioning systems are being coated externally to improve corrosion resistance, water drainage, and reduce potential odor concerns. The coating durability and efficiency in achieving its corrosion resistance depends on the coating uniformity and adhesion characteristics. Good coating adhesion on aluminum surface can be achieved after freeing the surface from the oxide and flux residues. Evaporators manufactured by the Controlled Atmosphere Brazing (CAB) process have flux residue remaining on the surface, the presence of which interferes with the coating process and also affects the performance of coated components. A methodology to quantify the effect of high Nocolok flux residue on heat exchanger coating uniformity has been presented.

Welding is one of the most commonly used fabrication method in various automotive applications. Welding is a metallurgical fusion process in which parts or work pieces to be joined are heated above their melting temperature and then solidified. Some of the effects of the welding include residual stresses and Heat Affected Zone (HAZ). A methodology is proposed to study the welding process using the commercial finite element software, ABAQUS. Non linear transient heat transfer analysis is used. Effects of heat energy input rate and heat input time on residual stresses and HAZ are determined.

Three dimensional acoustic entertainment enables the listener to experience sounds emanating from all around them, rather than being limited to the space between a pair of stereo speakers. It provides the artist with an enhanced sonic pallet to place sound sources in three dimensional space, as well as potential for a more realistic music reproduction experience. With the popularity of the Digital Versatile Disc (DVD), the technology successfully migrated from the movie theater into the “home theater”. The multichannel replacements for the audio CD (DVD-Audio and Super Audio CD) are enhancing the advancement into the automotive space. Automotive interiors are readymade for multichannel reproduction, but the automotive environment offers some challenges as well. This paper will discuss the market and technical potential for automotive applications of three dimensional sound, matters to take into account, media choices, distribution considerations and a look toward the future.

The work presented here outlines the development of a robust CAO tool for optimal design of electromagnetic retarder machines. The developed EM-CAO tool is then used to perform a wide variety of CAE/CAO tasks, from automatically computing the torque versus rpm performance curves of the EM retarder to performing optimization. Two specific examples of optimal design of the EM retarder are reported. Through the use of a task manager/optimizer repetitive jobs are fully automated thereby making the analysis and optimization of electromagnetic retarders faster and user-friendlier.