Search Results

E-Mobility and low noise IC Engines has pushed product development teams to focus more on sound quality rather than just on reduced noise levels and legislative needs. Furthermore, qualification of products from a sound quality perspective from an end of line testing requirement is also a major challenge. End of line (EOL) NVH testing is key evaluation criteria for product quality with respect to NVH and warranty. Currently for subsystem or component level evaluation, subjective assessment of the components is done by a person to segregate OK and NOK components. As human factor is included, the process becomes very subjective and time consuming. Components with different acceptance criteria will be present and it’s difficult to point out the root cause for NOK components. In this paper, implementation of machine learning is done for acoustic source detection at end of line testing.

This paper presents an experimental investigation of the impact of EGR dilution on the tradeoff between flame and end-gas autoignition heat release in a Spark-Assisted Compression Ignition (SACI) combustion engine. The mixture was maintained stoichiometric and fuel-to-charge equivalence ratio (ϕ′) was controlled by varying the EGR dilution level at constant engine speed. Under all conditions investigated, end-gas autoignition timing was maintained constant by modulating the mixture temperature and spark timing. Experiments at constant intake pressure and constant spark timing showed that as ϕ′ is increased, lower mixture temperatures are required to match end-gas autoignition timing. Higher ϕ′ mixtures exhibited faster initial flame burn rates, which were attributed to the higher laminar flame speeds immediately after spark timing and their effect on the overall turbulent burning velocity.

Non-reacting spray behaviors of the Engine Combustion Network “Spray G” gasoline fuel injector were investigated at flash and non-flash boiling conditions in an optically accessible single cylinder engine and a constant volume spray chamber. High-speed Mie-scattering imaging was used to determine transient liquid-phase spray penetration distances and observe general spray behaviors. The standardized “G2” and “G3” test conditions recommended by the Engine Combustion Network were matched in this work and the fuel was pure iso-octane. Results from the constant volume chamber represented the zero (stationary piston) engine speed condition and single cylinder engine speeds ranged from 300 to 2,000 RPM. As expected, the present results indicated the general spray behaviors differed significantly between the spray chamber and engine. The differences must be thoughtfully considered when applying spray chamber results to guide spray model development for engine applications.

High-pressure gasoline fuel injection is a means to improve combustion efficiency and lower engine-out emissions. The objective of this study was to quantify the effects of fuel injection pressure on transient gasoline fuel spray development for a wide range of injection pressures, including over 1000 bar, using a constant volume chamber and high-speed imaging. Reference grade gasoline was injected at fuel pressures of 300, 600, 900, 1200, and 1500 bar into the chamber, which was pressurized with nitrogen at 1, 5, 10, and 20 bar at room temperature (298 K). Bulk spray imaging data were used to quantify spray tip penetration distance, rate of spray tip penetration and spray cone angle. Near-nozzle data were used to evaluate the early spray development.

Connectivity has become an essential need for daily device users. With the car projected to be the “ultimate mobile device”, connectivity modules will eventually be mainstream in every car. Network providers are expanding their infrastructure and technology to accommodate the connected cars. Besides making voice and emergency calls the connected car will be sharing data with telematics service providers, back end systems and other vehicles. This trend will increase vehicle modules, complexity, entry points and vulnerabilities. This paper will present the current connected car architectures. The paper will present current architectural issues of the connected car and its vulnerabilities. The paper will present a new proposed architecture for the future connected car that enhances efficiency and security.

Low-pressure cooled EGR (LP-cEGR) systems can provide significant improvements in spark-ignition engine efficiency and knock resistance. However, open-loop control of these systems is challenging due to low pressure differentials and the presence of pulsating flow at the EGR valve. This research describes a control structure for Low-pressure cooled EGR systems using closed loop feedback control along with internal model control. A Smith Predictor based PID controller is utilized in combination with an intake oxygen sensor for feedback control of EGR fraction. Gas transport delays are considered as dead-time delays and a Smith Predictor is one of the conventional methods to address stability concerns of such systems. However, this approach requires a plant model of the air-path from the EGR valve to the sensor.

Today open source software is widely used in different domains like Desktop systems, Consumer electronics (smart phones, TV, washing machines, camera, printers, smart watches), Automotive, Automation etc. With the increased involvement of the open source software in the different domains including the safety critical ones, there has been a requirement of the well-defined test strategy to test and verify such systems. Currently there are multiple open source tools and frameworks to choose from. The paper describes the various open source test strategies and tools available to qualify such systems, their features, maintenance, community support, advantages and disadvantages. Target audience would be the software engineers, program managers, using an open source stack for the product development.

Automotive systems can generate un-intentional radio frequency energy. The levels of these emissions must be below maximum values set by the Original Equipment Manufacturer (OEM) for customer satisfaction and/or in order to meet governmental requirements. Due to the complexity of electromagnetic coupling mechanisms that can occur on a vehicle, many times it is difficult to measure and identify the noise source(s) without the use of an electromagnetic interference (EMI) receiver or spectrum analyzer (SA). An efficient and effective diagnostic solution can be to use a low-cost portable, battery powered RF detector with wide dynamic range as an alternative for automotive electromagnetic compatibility (EMC) and design engineers to identify, locate, and resolve radio frequency (RF) noise problems. A practical circuit described here can be implemented easily with little RF design knowledge, or experience.

This paper presents an overview of the evolution & revolution of automotive E/E architectures and how we at Bosch, envision the technology in the future. It provides information on the bottlenecks for current E/E architectures and drivers for their evolution. Functionalities such as automated driving, connectivity and cyber-security have gained increasing importance over the past few years. The importance of these functionalities will continue to grow as these cutting-edge technologies mature and market acceptance increases. Implementation of these functionalities in mainstream vehicles will demand a paradigm shift in E/E architectures with respect to in-vehicle communication networks, power networks, connectivity, safety and security. This paper expounds on these points at a system level.

HCCI (Homogeneous Charge Compression Ignition) has the potential for significant fuel efficiency improvements and low engine-out emissions but a major limitation is its relatively small operating range, limited by pressure rise rate at high loads and cyclic variability and incomplete combustion at low loads. Spark Assisted Compression Ignition (SACI) can extend the operating range of HCCI, but since SACI includes both flame propagation and auto-ignition, it experiences higher cyclic variance than HCCI combustion and phasing control can be challenging. This paper investigates the effects of environmental conditions on SACI combustion. The first part of the paper investigates whether CA50 (the location of 50% heat release and the most commonly used combustion parameter for describing combustion phasing) is the best metric to describe combustion phasing and facilitate its control. CA50 and four other combustion phasing metrics are evaluated and compared in this study.

Spark Assisted Compression Ignition (SACI) aims to increase the load limit of homogeneous charge compression ignition (HCCI) engines, enabling the benefits of dilute combustion over a larger engine operation range. Compared to HCCI, SACI exhibits higher cyclic variation of several combustion features. Due to the necessity of control of the timing of the auto-ignition event during SACI operation, a suitable characterization of the combustion at a given set of actuator inputs is required to enable robust model-based controls of combustion. This paper investigates statistical approaches to analyze in-cylinder pressure data of SACI in order to find a real or reconstructed cycle that will represent the important characteristics of combustion. To determine the representativeness of such a cycle, several combustion characteristics were compared that could serve as operational limits.

Electronics components are estimated to be between 9 to 15 % of a total vehicle cost, and this trend will remain strong for the next years. The amount of electronics content in a vehicle has grown steadily since 1970's, and as a result, development challenges such as testing and validation are a key aspect of its overall development costs. Testing costs can amount easily to US$ 500 k in medium complex automotive parts of a vehicle (e.g. instrument cluster) depending on a specific OEM customer demand, and this on top of limited regional laboratory capacity can also lead to increased testing time. The goal of this paper is to outline key aspects of electronics in vehicle components testing, including overall costs and timing, and propose a lean approach to optimize such costs & timing. The key aspects of such optimization include not only resources, but also laboratories and upfront OEM customer planning.

This paper presents an assessment of competing algorithms for normalizing volume levels between tracks and/or sources in an automotive infotainment system. Portable media players such as smartphones and iPod® devices are extremely popular for listening to music collections or streaming content from the Internet. The lack of normalization is a source of dissatisfaction if the user experiences significant changes in audio level between tracks. Several commercially available algorithms exist to solve this problem. This research includes a double-blind listening test comparing an audio sample processed with the different leveling algorithms to an unprocessed reference. The listener preference rating is recorded and results indicate which algorithm is preferred.

In automotive infotainment systems, multiple types of digital audio signals are usually present. Some come from internal sources, such as a CD or USB stick, and some come from external sources, such as an internet stream or digital radio. These sources usually have different sample-rates, and may also be different from one or more system sample-rates. Managing and transporting these signals throughout the system over different sample-rate domains require detailed upfront architecture analysis and correct system design to ensure signal quality is maintained to the desired level. Incorrect design can add significant user-perceivable noise and distortion. This paper examines the key analysis factors, the effects of poor design and the approaches for achieving robust signal handling and ensuring desired signal quality.

Accurate evaluation of vehicles' transient total power requirement helps achieving further improvements in vehicle fuel efficiency. When operated, the air-conditioning (A/C) system is the largest auxiliary load on a vehicle, therefore accurate evaluation of the load it places on the vehicle's engine and/or energy storage system is especially important. Vehicle simulation models, such as "Autonomie," have been used by OEMs to evaluate vehicles' energy performance. However, the load from the A/C system on the engine or on the energy storage system has not always been modeled in sufficient detail. A transient A/C simulation tool incorporated into vehicle simulation models would also provide a tool for developing more efficient A/C systems through a thorough consideration of the transient A/C system performance. The dynamic system simulation software MATLAB/Simulink® is frequently used by vehicle controls engineers to develop new and more efficient vehicle energy system controls.

With the publication of ISO26262 [1] and the concept of Functional Safety, being able to identify the required safety integrity level for software components and defining the respective development steps has become increasingly important. A number of Tier 1 automotive suppliers, including Robert Bosch LLC, have been developing software for safety relevant systems, and have experience with a number of methods and tools for software analysis. This paper will focus on the pros and cons of the Criticality Analysis method. Criticality Analysis (CA) is a method that rates outputs, sub-components and inputs to a function based on the ASIL rating of the function. Faller [2] proposed the use of CA in conjunction with IEC 61508 safety standard, and this author proposes that the CA can also be used in conjunction with ISO 26262. CA allows taking a function with any ASIL rating and breaking down the signal chain to develop safety requirements at each stage (see [2, 3]).

This paper describes an investigation about the efficiency of safety-related non-functional software unit tests (NFSWUT). Well defined design, implementation and test processes are widely used in the respective industry. In order to fulfill the ISO 26262[1] requirement, additional effort is necessary to execute the NFSWUT. However, the efficiency of these tests is still not confirmed. This paper will provide an overview about an investigation of the effort-benefit ratio of the NFSWUT.

Estimation and prediction of residual life and reliability are serious concerns in life cycle management for aging structures. Laboratory testing replicating fatigue loading for a typical military aircraft wing skin was undertaken. Specimens were tested until their fatigue life expended reached 100% of the component fatigue life. Then, scanning electron microscopy was used to quantify the size and location of fatigue cracks within the high stress regions of simulated fastener holes. Distributions for crack size, nearest neighbor distances, and spatial location were characterized statistically in order to estimate residual life and to provide input for life cycle management. Insights into crack initiation and growth are also provided.

EPA and NHTSA have harmonized Regulations for Greenhouse Gas (GHG) emissions and Corporate Average Fuel Economy (CAFE) for model year (MY) 2012-16, published on April 1st, 2010. This requirement applies to all passenger cars and light trucks. Therefore the reduction of CO₂ emissions will be a major challenge for the automotive industry in the coming years to achieve the targets (GHG & CAFE) of 250 g/mi CO₂ and 35.5 miles per gallon (mpg) for MY 2016. In addition to combustion engine improvements, vehicle energy management and operating strategies offer a huge potential to reduce CO₂ emissions through innovative electronic systems. The paper will show a possible implementation of a holistic vehicle energy management system including the operating strategy "Free wheeling." Starting from a top-down approach, we have developed operating strategies that offer the possibility to optimize the energy usage of the entire system.

Active safety systems will have a great impact in the next generation of vehicles. This is partly originated by the increasing consumer's interest for safety and partly by new traffic safety laws. Control actions in the vehicle are based on an extensive environment model which contains information about relevant objects in vehicle surroundings. Sensor data fusion integrates measurements from different surround sensors into this environment model. In order to avoid system malfunctions, high reliability in the interpretation of the situation, and therefore in the environment model, is essential. Hence, the main idea of data fusion is to make use of the advantages of using multiple sensors and different technologies in order to fulfill these requirements, which are especially high due to autonomous interventions in vehicle dynamics (e. g. automatic emergency braking).