Refine Your Search

Date

Date

Torque converters Flywheels Automatic Transmission and Transaxle Committee Crankcases

Search Results

Viewing 1 to 20 of 28
12Next >Last >>
Sort by published
Standard

Engine Flywheel Housing and Mating Transmission Housing Flanges
2020-09-29
CURRENT
J617_202009
This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.
Standard

Hydrodynamic Drives Terminology
2019-12-02
CURRENT
J641_201912
Since the torque converter and fluid coupling are commonly used components of automatic transmissions in industry, the SAE appointed a committee to standardize terminology, test procedure, data recording, design symbols, and so forth, in this field. The following committee recommendations will facilitate a clear understanding for engineering discussions, comparisons, and the preparation of technical papers. The recommended usages represent the predominant practice or the acceptable practice. Where agreement is not complete, alternates have been included for clarification. EXAMPLE: Two systems of blade angle designations are described. Consequently, when a blade angle is specified, the system should be designated. This SAE Recommended Practice deals only with the physical parts and dimensions and does not attempt to standardize the design considerations, such as the actual fluid flow angle resulting from the physical blade shape.
Standard

Automotive Transmission Terminology
2017-08-25
HISTORICAL
J645_201708
The following listed definitions are intended to establish terminology and criteria for describing the various kinds of automotive transmissions. A specific arrangement may be described by a combination of several of these definitions.
Standard

Passenger Car and Light Truck Automatic Transmission and Automatic Transaxle Test Code
2015-06-30
CURRENT
J651_201506
The extent of test conditions on the dynamometer must be sufficient to determine the efficiency characteristics corresponding to the following range of vehicle operations in all gear ratios with locked torque converters (open converter can also be done where appropriate and noted). a Efficiency versus output speed versus input torque b Torque ratio versus output speed c Input speed versus output speed d Output torque versus output speed e Parasitic loss versus input speed (spin losses) f Cooler flow g Output torque bias (front wheel drive transaxles)
Standard

Engine Flywheel Housing and Mating Transmission Housing Flanges
2014-04-16
HISTORICAL
J617_201404
This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.
Standard

Flywheels for Engine-Mounted Torque Converters
2012-06-11
CURRENT
J927_201206
This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for engine flywheel mounted torque converters. Tables 1A and 1B and Figure 1 give dimensions for flywheels mounted-type torque converters. For torque converters using drive ring overcenter type disconnect clutch, see SAE J620.
Standard

Hydrodynamic Drives Terminology
2012-06-04
HISTORICAL
J641_201206
Since the torque converter and fluid coupling are commonly used components of automatic transmissions in industry, the SAE appointed a committee to standardize terminology, test procedure, data recording, design symbols, and so forth, in this field. The following committee recommendations will facilitate a clear understanding for engineering discussions, comparisons, and the preparation of technical papers. The recommended usages represent the predominant practice or the acceptable practice. Where agreement is not complete, alternates have been included for clarification. This SAE Recommended Practice deals only with the physical parts and dimensions and does not attempt to standardize the design considerations, such as the actual fluid flow angle resulting from the physical blade shape.
Standard

Engine Flywheel Housing and Mating Transmission Housing Flanges
2012-05-31
HISTORICAL
J617_201205
This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.
Standard

Automotive Transmission Terminology
2009-03-03
HISTORICAL
J645_200903
The following listed definitions are intended to establish terminology and criteria for describing the various kinds of automotive transmissions. A specific arrangement may be described by a combination of several of these definitions.
Standard

Passenger Car and Light Truck Automatic Transmission and Automatic Transaxle Test Code
2005-06-22
HISTORICAL
J651_200506
To provide a means of obtaining the efficiency characteristics of automatic transmissions and automatic transaxles. It outlines dynamometer tests that map the steady-state characteristics over a range of operations of an automatic transmission/automatic transaxle and provides a method of presenting test data. This procedure must be followed, with similar test facilities so that results obtained from different laboratories are comparable. For this SAE Recommended Practice, the transmission is defined as the complete automatic transmission or transaxle assembly between the engine and the driveshaft(s) used to effect a ratio change in transmitting power. For 4WD/AWD, it does not include transfer case or power take off subsystems. This test procedure deals with the aspect of conducting complete transmission and transaxle assembly testing.
Standard

Hydrodynamic Drives Terminology
2000-03-10
HISTORICAL
J641_200003
Since the torque converter and fluid coupling have become commonly used components of automatic transmissions in industry, the SAE appointed a committee to standardize terminology, test procedure, data recording, design symbols, and so forth, in this field. The following committee recommendations will facilitate a clear understanding for engineering discussions, comparisons, and the preparation of technical papers. The recommended usages represent the predominant practice or the acceptable practice. Where agreement is not complete, alternates have been included for clarification. This SAE Recommended Practice deals only with the physical parts and dimensions and does not attempt to standardize the design considerations, such as the actual fluid flow angle resulting from the physical blade shape.
Standard

AUTOMOTIVE TRANSMISSION TERMINOLOGY
1997-07-01
HISTORICAL
J645_199707
The following listed definitions are intended to establish terminology and criteria for describing the various kinds of automotive transmissions. A specific arrangement may be described by a combination of several of these definitions.
Standard

PASSENGER CAR AND LIGHT TRUCK AUTOMATIC TRANSMISSION AND AUTOMATIC TRANSAXLE TEST CODE
1996-01-01
HISTORICAL
J651_199601
To provide a means of obtaining the performance characteristics of automatic transmissions and automatic transaxles. It outlines dynamometer tests that map the steady-state characteristics over a range of operations of an automatic transmission/automatic transaxle and provides a method of presenting test data. This procedure must be followed, with similar test facilities so that results obtained from different laboratories are comparable. For this SAE Recommended Practice, the transmission is defined as the complete automatic transmission or transaxle assembly between the engine and the driveshaft(s) used to effect a ratio change in transmitting power. This test procedure deals with the aspect of conducting complete transmission and transaxle assembly testing. However, by its very nature a transmission should be viewed as a compilation of three major component systems: pump, torque converter, and gearbox (all ratio change elements).
Standard

FLYWHEELS FOR ENGINE-MOUNTED TORQUE CONVERTERS
1995-03-05
HISTORICAL
J927_199503
This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for engine flywheel mounted torque converters. Tables 1A and 1B and Figure 1 give dimensions for flywheels mounted-type torque converters. For torque converters using drive ring overcenter type disconnect clutch, see SAE J620.
Standard

ENGINE FLYWHEEL HOUSING AND MATING TRANSMISSION HOUSING FLANGES
1992-05-01
HISTORICAL
J617_199205
This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.
Standard

PASSENGER CAR AND TRUCK AUTOMATIC TRANSMISSION TEST CODE
1991-01-23
HISTORICAL
J651_199101
To provide a means of comparing the performance characteristics of automatic transmissions. It outlines dynamometer tests that cover the range of operation of transmissions and provides a method of presenting the test data. This procedure must be followed with similar test facilities so that results obtained from different laboratories are comparable. For this SAE Recommended Practice, the transmission is defined as the complete assembly driven by the engine and used to effect a ratio change in transmitting power to the final drive system.
Standard

FLYWHEELS FOR ENGINE MOUNTED TORQUE CONVERTERS
1988-11-01
HISTORICAL
J927_198811
This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for engine flywheel mounted torque converters. Table 1 and Fig. 1 give dimensions for flywheel mounted-type torque converters. For torque converters using drive ring overcenter type disconnect clutch, see SAE J620.
Standard

AUTOMOTIVE TRANSMISSION TERMINOLOGY
1986-05-01
HISTORICAL
J645_198605
The following listed definitions are intended to establish terminology and criteria for describing the various kinds of automotive transmissions. A specific arrangement may be described by a combination of several of these definitions.
12Next >Last >>
X