Search Results

This paper presents a stability monitoring algorithm with a combined slip tire model for maximized cornering speed of high-speed autonomous driving. It is crucial to utilize the maximum tire force with maintaining a grip driving condition in cornering situations. The model-free cruise controller has been designed to track the desired acceleration. The lateral motion has been regulated by the sliding mode controller formulated with the center of percussion. The controllers are suitable for minimizing the behavior errors. However, the high-level algorithm is necessary to check whether the intended motion is inside of the limit boundaries. In extreme diving conditions, the maximum tire force is limited by physical constraints. A combined slip tire model has been applied to monitor vehicle stability. In previous studies, vehicle stability was evaluated only by vehicle acceleration.

This paper presents an integrated control of in-wheel motor (IWM) and electronic limited slip differential (eLSD) to enhance the vehicle lateral stability and maneuverability. The two actuators are utilized in the proposed controller to achieve separate purposes. The IWM controller is designed to modify the understeer gradient for enhanced handling characteristic and maneuverability. The eLSD controller is devised to improve the lateral stability to prevent oversteer in a severe maneuver. The proposed controller consists of a supervisor, upper-level controller and lower-level controller. The supervisor determines a target motion based on a target understeer gradient for IWM control and a yaw rate reference for eLSD control. The upper-level controller generates a desired yaw moment for the target motion. In the lower-level controller, the desired yaw moment is converted to the control inputs for IWMs in the two front wheels and eLSD at the rear axle.

This paper presents an Interacting Multiple Model (IMM) based side slip angle estimation method to estimate side slip angle under various road conditions for vehicle stability control. Knowledge of the side slip angle is essential enhancing vehicle handling and stability. For the estimation of the side slip angles in previous researches, prior knowledge of tire parameters and road conditions have been employed, and sometimes additional sensors have been needed. These prior knowledge and additional sensors, however, necessitates many efforts and make an application of the estimation algorithm difficult. In this paper, side slip angle has been estimated using on-board vehicle sensors such as yaw rate and lateral acceleration sensors. The proposed estimation algorithm integrates the estimates from multiple Kalman filters based on the multiple models with different parameter set.

This paper presents an integrated chassis control method for vehicle stability under various road friction conditions without information on tire-road friction. For vehicle stability, vehicle with an integrated chassis control needs to cope with the various road friction conditions. One of the chassis control method under various road conditions is to determine and/or limit control inputs based on tire-road friction coefficient. The tire-road friction coefficient, however, is difficult to estimate and still a challenging task. The key idea for the proposed method without the estimation of the tire-road friction coefficient is to analyze and control vehicle states based on a tire slip angle - tire force phase plane, i.e. based on these vehicle responses: tire forces and tire slip angles of front/rear wheels.

This paper presents the integrated chassis control(ICC) of four-wheel drive(4WD), electronic stability control(ESC), electronic control suspension(ECS), and active roll stabilizer(ARS) for limit handling. The ICC consists of three layers: 1) a supervisor determines target vehicle states; 2) upper level controller calculates generalized forces; 3) lower level controller, which is contributed in this paper, optimally allocates the generalized force to chassis modules. The lower level controller consists of two integrated parts, 1) longitudinal force control part (4WD/ESC) and 2) vertical force control part (ECS/ARS). The principal concept of both algorithms is optimally utilizing the capability of the each tire by monitoring tire saturation, with tire combined slip. By monitoring tire saturation, 4WD/ESC integrated system minimizes the sum of the tire saturation, and ECS/ARS integrated system minimizes the variance of the tire saturation.

As an effective approach for the design, implementation and test of control systems, hardware-in-the-loop (HIL) test has been used in many research areas. This paper describes a real-time HIL simulation test for an automotive electronic control system. The HIL system proposed in this paper consists of three parts: real-time target hardware, electronic control unit (ECU) of the automotive electronic control systems and a signal-conditioning unit which regulates the voltage levels between real-time target and ECU. The HIL simulation evaluates mechanical and electronic behaviors in real time using off-line simulation models by interfacing real-target with electrical control units via interface box. The model has been developed by MATLAB/Simulink. The model is composed of mechanical part which predicts dynamic behaviors and electronic part to calculate the motor speeds, current and electronic loads under the various conditions.

This paper describes an Integrated Chassis Control (ICC) strategy for improving high speed cornering performance by integration of Electronics Stability Control (ESC), Four Wheel Drive (4WD), and Active Roll Control System (ARS). In this study, an analysis of various chassis modules was conducted to prove the control strategies at the limits of handling. The analysis is focused to maximize the longitudinal velocity for minimum lap time and ensure the vehicle lateral stability in cornering. The proposed Integrated Chassis Control algorithm consists of a supervisor, vehicle motion control algorithms, and a coordinator. The supervisor monitors the vehicle status and determines desired vehicle motions such as a desired yaw rate, longitudinal acceleration and desired roll motion. The target longitudinal acceleration is determined based on the driver's intention and vehicle current state to ensure the vehicle lateral stability in high speed maneuvering.

This paper describes a driving motor torque distribution strategy of six-wheel-driven electric vehicles for optimized energy consumption. In this research, this strategy minimizes motoring power consumption and maximizes regenerative braking power under given required power condition. The torque distribution controller consists of total required motor torque calculation part, upper and optimal torque calculation part, lower level controller. The upper level controller determines total required torque of vehicle. And the torque is determined by acceleration pedal input of driver and vehicle velocity. The lower level controller calculates energy consumption in given condition and distributes motor torque to driving motor minimizing energy consumption. In distributing optimal motor torque, it is important to get accurate characteristics of driving motor and performance constraint.

This paper is concerned with the torque distribution problem including slip limitation and actuator fault tolerance to improve vehicle lateral stability and maneuverability of six-wheeled skid-steered vehicles. The torque distribution algorithm to distribute wheel torque to each wheel of a skid-steered vehicle consists of an upper level control layer, a lower level control layer and an estimation layer. The upper level control layer is designed to obtain longitudinal net force and desired yaw moment, while the lower level control layer determines distributed driving and braking torques to six wheels. The algorithm takes vehicle speed, slip ratio and tire load information from the estimation layer, as well as actuator fault information from each in-wheel motor controller unit.

A methodology to design a model free cruise control algorithm(MFCC) is presented in this paper. General cruise control algorithms require lots of vehicle parameters to control the power train and the brake system, that makes control system complicate. Moreover, when the target vehicle is changed, the vehicle parameters should be reinvestigated in order to apply the cruise control algorithm to the subject vehicle. To overcome these disadvantages of the conventional cruise control algorithm, MFCC algorithm has been developed. The algorithm directly determines the throttle, brake inputs based on the reference model parameters such as clearance, relative velocity, and subject vehicle acceleration. This simple structure facilitates human centered design of cruise controller and makes it easy to apply control algorithm to various vehicles without reinvestigation of vehicle parameters.

This paper describes a lane departure avoidance system to help the driver avoid the lane departure during drowsiness or inattention. The lane departure avoidance system proposed in this paper consists of unintended lane departure decision part, upper level controller part and lower level controller part. The index used in unintended lane departure decision part is proposed to monitor a driver's intention with steering behaviors. The desired dynamics is calculated in upper level controller part. When the desired dynamics is calculated, it is considered to guarantee a driver's safety and smooth ride feel simultaneously as possible. The lower level controller distributes the desired control input to actuators, motor driven power steering (MDPS) module and vehicle stability control (VSC) module. The proposed lane departure avoidance system has been evaluated via human driver model-in the loop simulation.

This paper describes development and performance verification of a driving control algorithm for a 6 wheel driving and 6 wheel steering (6WD/6WS) vehicle using a real-time simulator. This control algorithm is developed to improve vehicle stability and maneuverability under high speed driving conditions. The driving controller consists of stability decision, upper, lower level and wheel slip controller. The stability decision algorithm determines desired longitudinal acceleration and reference yaw rate in order to maintain lateral and roll stability using G-vectoring method. Upper level controller is designed to obtain reference longitudinal net force, yaw moment and front/middle steering angles. The longitudinal net force is calculated to satisfy the reference longitudinal acceleration by the PID control theory. The reference yaw moment is determined to satisfy the reference yaw rate using sliding control theory. Lower level controller determines distributed tractive/braking torques.

This paper describes vehicle stability control (VSC) scheme to prevent rollover and to improve both maneuverability and lateral stability by integrating individual chassis control modules such as electronic stability control (ESC), active front steering (AFS) and continuous damping control (CDC). The proposed VSC system consists of an upper and lower level controller. The upper level controller determines a control mode such as rollover mitigation, maneuverability and lateral stability, and it also calculate desired values for its objectives. The lower level controller determines longitudinal and lateral tire forces as inputs of each control modules such as the ESC and AFS. From the simulation results, it is shown that the proposed VSC system can prevent vehicle rollover, while at the same time improving both maneuverability and lateral stability

This paper presents a longitudinal control algorithm for an adaptive cruise control (ACC) with collision avoidance (CA) in multiple vehicle traffic situations. The proposed algorithm consists of a multi-target tracking filter, a primary target selection algorithm and an integrated ACC/CA system. The multi-target tracking filter is used to smooth the sensor signal, and makes it possible to apply to a control system. The primary target selection algorithm decides an in-lane target and provides the information to an integrated ACC/CA system in order to drive a subject vehicle smoothly and improve safety in complex traffic situations. Finally, the integrated ACC/CA system computes the desired acceleration. The performance and safety benefits of the multi-vehicle ACC/CA system is investigated via simulations using real data on driving. Simulation results show that the response of multi-vehicle ACC/CA system is more smooth and safer at a change of traffic situations.

The performance of an integrated Vehicle Stability Control (VSC) system depends on not only control logic itself, but also the performance of state estimator and control threshold. In conventional VSCs, a control threshold is designed by vehicle characteristics and is centered on average drivers. A VSC algorithm with variable control threshold has been investigated in this study. The control threshold can be determined by phase plane analysis of side slip angle and angular velocity. Vehicle side slip angle estimator has been evaluated using test data. Estimated side slip angle has been used in the determination of the control threshold. The performance of the proposed VSC algorithm has been investigated by human-in-the-loop simulation using a vehicle simulator. The simulation results show that the control threshold has to be determined with respect to the driver steering characteristics.

This paper presents a closed-loop evaluation of the Vehicle Stability Control (VSC) systems using a vehicle simulator. Human driver-VSC interactions have been investigated under realistic operating conditions in the laboratory. Braking control inputs for vehicle stability enhancement have been directly derived from the sliding control law based on vehicle planar motion equations with differential braking. A driving simulator which consists of a three-dimensional vehicle dynamic model, interface between human driver and vehicle simulator, three-dimensional animation program and a visual display has been validated using actual vehicle driving test data. Real-time human-in-the loop simulation results in realistic driving situations have shown that the proposed controller reduces driving effort and enhances vehicle stability.

An estimation algorithm for vehicle driving load has been proposed in this paper. Driving load is an important factor in a vehicle's longitudinal motion control. An approach using an observer is introduced to estimate driving load based on inexpensive RPM sensors currently being used in production vehicles. Also, the new torque estimation technique using neural network has been incorporated in this estimation algorithm to achieve better performance over variations in the automotive power transmissions process. The effectiveness of the observer-based method is demonstrated through the use of a nonlinear full vehicle simulation model in various scenarios. The proposed method using an observer has good performance, both over modeling error in powertrain system and under the uncertain environment of a running vehicle.

A throttle/brake control law for the intelligent cruise control (ICC) system has been proposed in this paper. The ICC system consists of a vehicle detection sensor, a controller and throttle/brake actuators. For the control of a throttle/brake system, we introduced a solenoid-valve-controlled electronic vacuum booster (EVB) and a step-motor-controlled throttle actuator. Nonlinear computer model for the electronic vacuum booster has been developed and the simulations were performed using a complete nonlinear vehicle model. The proposed control law in this paper consists of an algorithm that generates the desired acceleration/deceleration profile in an ICC situation, a throttle/brake switching logic and a throttle and brake control algorithm based on vehicle dynamics. The control performance has been investigated through computer simulations and experiments.