Search Results

Abstract A detailed investigation was carried out on the performance, combustion, and emissions of a single-cylinder direct injection hydrogen spark ignition (SI) engine with either a side-mounted direct injection (SDI) or a centrally installed direct injection (CDI) injector. The first part of the study analyzed the performance and emissions characteristics of CDI and SDI engine operations with different injection timings and pressures. This was followed by comparing the engine’s performance and emissions of the CDI and SDI operations at different engine speeds and relative air-to-fuel ratios (lambda) with the optimized injection pressure and timings. Furthermore, the performance and emission attributes of the hydrogen engine with the CDI and SDI setups were conducted at a fixed λ value of 2.75 across a broad spectrum of engine loads. The study’s main outcome demonstrates that both direct injection systems produced near-zero CO2, CO, and HC emissions.

Abstract Driving schedule of every vehicle involves transient operation in the form of changing engine speed and load conditions, which are relatively unchanged during steady-state conditions. As well, the results from transient conditions are more likely to reflect the reality. So, the current research article is focused on analyzing the biofuel-like lemon peel oil (LPO) behavior under real-world transient conditions with fuel injection parameter MAP developed from steady-state experiments. At first, engine parameters and response MAPs are developed by using a response surface methodology (RSM)-based multi-objective optimization technique. Then, the vehicle model has been developed by incorporating real-world transient operating conditions. Finally, the developed injection parameters and response MAPs are embedded in the vehicle model to analyze the biofuel behavior under transient operating conditions.

Abstract The cooperative platoon of multiple trucks with definite proximity has the potential to enhance traffic safety, improve roadway capacity, and reduce fuel consumption of the platoon. To investigate the truck platooning performance in a real-world environment, two Peterbilt class-8 trucks equipped with cooperative truck platooning systems (CTPS) were deployed to conduct the first-of-its-kind on-road commercial trial in Canada. A total of 41 CTPS trips were carried out on Alberta Highway 2 between Calgary and Edmonton during the winter season in 2022, 25 of which were platooning trips with 3 to 5 sec time gaps. The platooning trips were performed at ambient temperatures from −24 to 8°C, and the total truck weights ranged from 16 to 39 tons. The experimental results show that the average time gap error was 0.8 sec for all the platooning trips, and the trips with the commanded time gap of 5 sec generally had the highest variations.

Abstract Methanol is emerging as an alternate internal combustion engine fuel. It is getting attention in countries such as China and India as an emerging transport fuel. Using methanol in spark ignition engines is easier and more economical than in compression ignition engines via the blending approach. M85 (85% v/v methanol and 15% v/v gasoline) is one of the preferred blends with the highest methanol concentration. However, its physicochemical properties significantly differ from gasoline, leading to challenges in operating existing vehicles. This experimental study addresses the challenges such as cold-start operation and poor throttle response of M85-fueled motorcycle using a port fuel injection engine. In this study, M85-fueled motorcycle prototype is developed with superior performance, similar/better drivability, and lower emissions than a gasoline-fueled port-fuel-injected motorcycle.

Abstract Tank-to-wheels (TTW) CO2 reduction for ethanol blends is determined from either gasoline composition or vehicle exhaust measurements. Fuels are characterized using a carbon intensity (CI), which is the ratio of carbon (as CO2 mass) in the fuel to the net heating value. Our objective is to assess changes in CI of market gasoline with varying ethanol content that can be used to appreciate change in vehicle tailpipe greenhouse gases (GHG) in response to policy controlling the ethanol level in market fuels. Ethanol has both a reduced carbon content and a reduced net (lower) heating value relative to petroleum species, with a CI slightly lower than that of typical petroleum gasoline. However, ethanol blending offers additional CI reduction because it enables a reduction of aromatics in the petroleum blendstock for oxygenate blending (BOB) while maintaining octane rating of the blend. Aromatics have a CI about 20% higher than paraffins.

Abstract The European Union’s pro-ecological policy imposes a requirement to use biofuel additives in diesel fuel which is supposed to support the sustainable development of transport and limit its negative impact on the natural environment. The study presents an analysis of the exhaust gas components and the amount of solid particles carried out for internal combustion engines fueled with mixtures of diesel fuel and fatty acid methyl esters. Additionally, the computer software of the tested power units was modified by changing the amount of fuel to be supplied and the air intake. The goal of the tests was to find out how the fuel mixture and reprogramming of the computer control systems would impact the emission of exhaust gas components. Based on the tests, it was found that an additive of fatty acid methyl esters to diesel does have an influence on the tested unit parameters.

Abstract Since the steady-state computational fluid dynamics (CFD) Reynolds-averaged Navier–Stokes (RANS) turbulence models offer low-cost and sensible accuracy, they are frequently utilized for bluff bodies’ external aerodynamics investigations (e.g., upwind, crosswind, and shape optimization). However, no firm certainty is made regarding the best model in terms of accuracy and cost. Based on cost and accuracy aspects, four RANS turbulence models were studied, which are Spalart–Allmaras, realizable k-ε, RNG k-ε, and SST k-ω. Ahmed body with a 25° slant angle benchmark case was introduced for this investigation. Two grids were generated to satisfy the near-wall treatment of each turbulence model. All grid settings were proposed and discussed in detail. Fluid-structure analysis was performed on five different planes.

Abstract Parking an articulated vehicle is a challenging task that requires skill, experience, and visibility from the driver. An automatic parking system for articulated vehicles can make this task easier and more efficient. This article proposes a novel method that finds an optimal path and controls the vehicle with an innovative method while considering its kinematics and environmental constraints and attempts to mathematically explain the behavior of a driver who can perform a complex scenario, called the articulated vehicle park maneuver, without falling into the jackknifing phenomena. In other words, the proposed method models how drivers park articulated vehicles in difficult situations, using different sub-scenarios and mathematical models.

Abstract Emissions and effects of climate change have prompted study into fuels that reduce global dependence on traditional fuels. This study seeks to investigate engine performance, thermochemical properties, emissions, and perform NVH analysis of Jet-A and S8 using a single-stage turbojet engine at three engine speeds. Experimental Jet-A results were used to validate a CFX simulation of the engine. Engine performance was quantified using thermocouples, pressure sensors, tachometers, flow meters, and load cells fitted to the engine. Emissions results were collected using an MKS Multigas Emissions Analyzer that examined CO, CO₂, H₂O, NOx, and THC. NVH analysis was conducted using a multifield, free-field microphone, and triaxial accelerometer. This study found that Jet-A operates at higher temperatures and pressures than S8, and S8 requires higher fuel flow rates than Jet-A, leading to poorer efficiency and thrust. S8 produced stronger vibrations over 5 kHz compared to Jet-A.

Abstract Biodiesel is a suitable alternative to diesel because of its carbon neutrality, renewability, lubricity, and lower pollutant emissions. However, extensive research indicates higher oxides of nitrogen (NOx) emissions with biodiesel. A practical method to combat this problem is utilizing water and biodiesel as emulsions. The effect of biodiesel-water emulsion in high-pressure fuel injection systems is not fully explored in the existing literature. The present study addresses this research gap by utilizing biodiesel-water emulsions in a modified light-duty diesel engine. The governor-controlled injection system was adapted to a fully flexible electronic system capable of high-pressure injection. Unlike other literature studies, the fuel injection timings were optimized with biodiesel-water emulsions to maximize brake thermal efficiency (bte) at every load condition.

Abstract Quantifying exhaust gas composition and temperature in vehicles with internal combustion engines (ICEs) is crucial to understanding and reducing emissions during transient engine operation. This is particularly important before the catalytic converter system lights off (i.e., during cold start). Most commercially available gas analyzers and temperature sensors are far too slow to measure these quantities on the timescale of individual cylinder-firing events, thus faster sensors are needed. A two-color mid-infrared (MIR) laser absorption spectroscopy (LAS) sensor for gas temperature and carbon monoxide (CO) mole fraction was developed and applied to address this technology gap. Two quantum cascade lasers (QCLs) were fiber coupled into one single-mode fiber to facilitate optical access in the test vehicle exhaust. The QCLs were time-multiplexed in order to scan across two CO absorption transitions near 2013 and 2060 cm–1 at 15 kHz.

Abstract The shot-to-shot variations in common rail injection systems are primarily caused by pressure wave oscillations in the rail, pipes, and injector body. These oscillations are influenced by fuel physical properties, injector needle movement, and pressure and suction control valve activations. The pressure waves are generated by pump actuation and injector needle movement, and their frequency and amplitude are determined by fluid properties and flow path geometry. These variations can result in cycle-to-cycle engine fluctuations. In multi-injection and split-injection strategies, the pressure oscillation from the first shot can impact the hydraulic characteristics of subsequent shots, resulting in variations in injection rate and amount. This is particularly significant when using alternative fuels such as biodiesel, which aim to reduce emissions while maintaining fuel atomization quality.

Abstract A rapid compression and expansion machine (RCEM) was used to experimentally investigate the ignition phenomena of dielectric-barrier discharge (DBD) in engine conditions. The effect of elevated pressure and temperature on ignition phenomena of a methane/air premixed mixture was investigated using a DBD igniter. The equivalence ratio was changed to elucidate the impact of DBD on flame kernel development. High-speed imaging of natural light and OH* chemiluminescence enabled visualization of discharges and flame kernel. According to experimental findings, the discharges become concentrated and the intensity increases as the pressure and temperature rise. Under different equivalence ratios, the spark ignition (SI) system has a shorter flame development time (FDT) as compared with the DBD ignition system.

Abstract TOC

Abstract The lightweight structure of a semitrailer composite leaf spring is designed and manufactured using glass fiber composite to replace the conventional steel leaf spring. The sliding composite mono leaf spring was designed based on the conventional parabolic spring design theory. The composites product design (CPD) module of CATIA software is used to create the lamination of the composite leaf spring. Using finite element analysis of the position and proportion of ±45° biaxial layer by OptiStruct software, it is found that a certain proportion (nearly 5%) of a ±45° biaxial layer can effectively reduce the shear stress under the condition of keeping the total number of layers fixed. Then, the natural frequency, stiffness, and strength of the composite leaf spring are simulated by the finite element method. Finally, the stiffness, fatigue, and matching of the designed spring are tested by experiments.

Abstract A rear underrun protection device (RUPD) plays a fundamental role in reducing the risk of running a small car beneath the rear or the side of a heavy truck because of the difference in structure heights in the event of a vehicle collision. Even in cars with five-star safety ratings, crashing into a truck with poorly designed RUPD results in a passenger compartment intrusion (PCI) more than the maximum allowable limit as per the United States (US) American National Highway Traffic Safety Administration (NHTSA) standards Federal Motor Vehicle Safety Standard (FMVSS). In this article, mild steel was used to fabricate the new designs of RUPD. The design was analyzed using finite element (FE) analysis LS-DYNA software. Simulations of a Toyota Yaris 2010 and Ford Taurus 2001 were performed at a constant speed of 63 km/h at the time of impact. The ability to prevent severe injuries in a collision with the rear side of the truck was estimated to optimize the underrun design.

Abstract Articulated vehicles form an important part of our society for the transport of goods. Compared to rigid trucks, tractor-trailer combinations can transport huge quantities of load without increasing the axle load. The fifth wheel (FW) acts as a bridge between the tractor and trailer, which can be moved within the range to achieve rated front and rear axle loads. When the FW is moved front, it adversely affects the cab dynamics and cab suspension forces. Compared to the cab pitch and roll, yaw motion increases drastically. The current study tries to address this issue by providing reaction rod links in the rear cab suspension. In this study, a 4×2 tractor with a three-axle semitrailer is considered by keeping the FW at its frontmost position, which is the worst-case scenario for a cab. Three different cases of reaction rod arrangement and its influence on cab dynamics are studied in comparison with a model without reaction rods.

Abstract Accurate exhaust gas temperature (EGT) measurements are vital in the design and development process of internal combustion engines (ICEs). The unsteady ICE exhaust flow and thermal inertia of commonly used sheathed thermocouples and resistance thermometers require high bandwidth EGT pulse measurements for accurate cycle-resolved and mean EGTs. The EGT pulse measurement challenge is typically addressed using exposed thin-wire resistance thermometers or thermocouples. The sensor robustness to response tradeoff limits ICE tests to short durations over a few exhaust conditions. Larger diameter multiwire thermocouples using response compensation potentially overcomes the tradeoff. However, the literature commonly adopts weaker slack wire designs despite indications of coated weld taut wires being robust.

Abstract The demand for fossil fuels can be reduced and environmental harm can be minimized by producing biodiesel from used cooking oil. This article was focused on investigating the combustion characteristics and regulated and unregulated emissions of a common-rail diesel engine fueled with different mixed concentrations of biodiesel and diesel fuel, including pure diesel fuel (B0), B10 (diesel containing 10%vol of biodiesel), B20, and B30. Experiments were conducted with three engine loads, corresponding to brake mean effective pressures (BMEP) of 0.289 MPa, 0.578 MPa, and 0.867 MPa at a constant speed of 1540 rpm. At medium and high loads, the waste cooking oil biodiesel (WCOB) increased in-cylinder pressure, advanced both the peak heat release rate and heat release center (CA50), shrunk the ignition delay (ID), and extended combustion duration (CD). The high viscosity of B30 blends under low load worsened the spray and led to poor combustion.

Abstract As a carbon-free power with excellent performance, the direct injection (DI) hydrogen-fueled internal combustion engine (H2-ICE) has the potential to contribute to carbon dioxide (CO2)-neutral on-road transport solutions. Aiming at high thermal efficiency, the influences of key factors on thermal efficiency over wide operating conditions of a turbocharging DI H2-ICE were investigated under the lean-burn strategy. And the nitrogen oxides (NOx) emission characteristics region was clarified in the high efficiency. The results confirm the optimal ignition strategy with the CA50 of 8–9 crank angle degrees after top dead center (°CA ATDC). The late-injection strategy manifests a significant advantage in brake thermal efficiency (BTE) compared with the early-injection strategy, and this advantage can be amplified by the increased load or injection pressure. The effects of injection (EOIs) pressure on BTE exhibit different laws at different EOIs.