Search Results

Clutches are commonly utilised in passenger type and off-road heavy-duty vehicles to disconnect the engine from the driveline and other parasitic loads. In off-road heavy-duty vehicles, along with fuel efficiency start-up functionality at extended ambient conditions, such as low temperature and intake absolute pressure are crucial. Off-road vehicle manufacturers can overcome the parasitic loads in these conditions by oversizing the engine. Caterpillar Inc. as the pioneer in off-road technology has developed a novel clutch design to allow for engine downsizing while vehicle’s performance is not affected. The tribological behaviour of the clutch will be crucial to start engagement promptly and reach the maximum clutch capacity in the shortest possible time and smoothest way in terms of dynamics. A multi-body dynamics model of the clutch system is developed in MSC ADAMS. The flywheel is introducing the same speed and torque as the engine (represents the engine input to the clutch).

Various engine platforms employ Selective Catalytic Reduction (SCR) technology to reduce the tail pipe emissions of oxides of nitrogen (NOx) from diesel engines as part of an overall strategy to comply with the emission regulations in place in various countries. High levels of NOx conversion (greater than 98%) in SCR aftertreatment may provide operating margin to increase overall fuel efficiency. However, to realize the potential fuel efficiency gains, the SCR technology employed should achieve high NOx conversion with limited reductant slip over transient application cycles in addition to steady state operation. A new approach to SCR controls was developed and implemented. This approach does not rely on any maps to determine the amount of urea solution to be dosed, thus significantly reducing calibration and development time and effort when implementing the SCR technology on multiple engine platforms and applications.

This paper features an application study on the impact of different blend levels of commercially-supplied biodiesel on engine and aftertreatment systems' durability and reliability as well as the impact on owning and operating factors: service intervals and fuel economy. The study was conducted on a bus application with a 2007 on highway emissions equipped engine running biodiesel blends of B5, B20, and B99 for a total period approaching 4500 hours. Biodiesel of waste cooking grease feedstock was used for the majority of the testing, including B5 and B20 blends. Biodiesel of soybean feedstock was used for testing on B99 blend. No negative impacts on engine and aftertreatment performance and durability or indication of future potential issues were found when using B5 and B20. For B99 measurable impacts on engine and aftertreatment performance and owning and operating cost were observed.

A method is presented for precise mounting of a hose model with any specified twist. Once mounting points and directions are specified, a hose of a specified length can be developed using discrete beams. A divide and conquer approach is employed to position, orient, decouple the free end of the hose model in a twist free state that is then twisted to a specified angle. The development of the kinematic elements necessary to do this is presented. Some Cosserat models have been shown to branch into multiple solutions while the method presented here has always converged to the minimum energy solution. The method for linking the hose model to other linkages is discussed as well one common error committed by users in implementing the link. In order to model the torsional properties of the hose, the torsional stiffness must be modified. A method for doing this using digital scans is discussed.

The objective of this project was to model and study the interior noise in an Off-Highway Truck cab using Statistical Energy Analysis (SEA). The analysis was performed using two different modeling techniques. In the first method, the structural members of the cab were modeled along with the panels and the interior cavity. In the second method, the structural members were not modeled and only the acoustic cavity and panels were modeled. Comparison was done between the model with structural members and without structural members to evaluate the necessity of modeling the structure. Correlation between model prediction of interior sound pressure and test data was performed for eight different load conditions. Power contribution analysis was performed to find dominant paths and 1/3rd octave band frequencies.

Fuel is a significant portion of the operating cost for an on-highway diesel engine and fuel economy is important to the economics of shipping most goods in North America. Cat® ACERT™ engine technology is no exception. Ball bearings have been applied to the series turbochargers for the Caterpillar heavy-duty, on-highway diesel truck engines in order to reduce mechanical loss for improved efficiency and lower fuel consumption. Over many years of turbocharger development, much effort has been put into improving the aerodynamic efficiency of the compressor and turbine stages. Over the same span of time, the mechanical bearing losses of a turbocharger have not experienced a significant reduction in power consumption. Most turbochargers continue to use conventional hydrodynamic radial and thrust bearings to support the rotor. While these conventional bearings provide a low cost solution, they do create significant mechanical loss.

Field testing of an extended life coolant technology in Class 8 trucks, equipped with Caterpillar C-12 engines revealed excellent coolant life with negligible inhibitor depletion to 400,000 miles with no refortification and no coolant top-off. In separate evaluations in Caterpillar 3406E equipped trucks, extended corrosion protection and component durability were established out to 700,000 miles, without the need for refortification other than top-off.

A cooperative program between the DOE Office of Heavy Vehicle Technology and Caterpillar is aimed at demonstrating electric turbo compound technology on a Class 8 truck engine. The goal is to demonstrate the level of fuel efficiency improvement attainable with an electric turbocompound system. The system consists of a turbocharger with an electric motor/generator integrated into the turbo shaft. The generator extracts surplus power at the turbine, and the electricity it produces is used to run a motor mounted on the engine crankshaft, recovering otherwise wasted energy in the exhaust gases. The electric turbocompound system also provides more control flexibility in that the amount of power extracted can be varied. This allows for control of engine boost and thus air/fuel ratio. The paper presents the status of development of an electric turbocompound system for a Caterpillar heavy-duty on-highway truck engine.

Nitrites have long been added to heavy-duty coolant to inhibit iron cylinder liner corrosion initiated by cavitation. However, in heavy-duty use, nitrites deplete from the coolant, which then must be refortified using supplemental coolant additives (SCA's). Recently, carboxylates have also been found to provide excellent cylinder liner protection in heavy-duty application. Unlike nitrites, carboxylate inhibitors deplete slowly and thus do not require continual refortification with SCA's. In the present paper laboratory aging experiments shed light on the mechanism of cylinder liner protection by these inhibitors. The performance of carboxylates, nitrites and mixtures of the two inhibitors are compared. Results correlate well with previously published fleet data. Specifically, rapid nitrite and slow carboxylate depletion are observed. More importantly, when nitrite and carboxylates are used in combination, nitrite depletion is repressed while carboxylates deplete at a very slow rate.

Silicate-free, carboxylate based technology as typified by Texaco Extended Life Coolant (TELC) and Caterpillar Extended Life Coolant (ELC), both meeting Caterpillar's EC-1 Coolant Specification, offer excellent corrosion protection for commercial lead solders commonly used in the fabrication of copper/brass radiators and heater cores throughout the trucking industry. Results of laboratory testing using solders from commercial radiators manufacturers and extensive field coolant analysis compare extended life technology with the popular conventional coolant technologies. In the laboratory, the effect of coolant concentration on solder protection is explored using the glassware corrosion test, ASTM D-1384. At concentrations ranging from 33% up to 75% the carboxylate technology offers comparable to superior protection when compared to the popular heavy-duty conventional coolant containing silicates and phosphates.

Improved fuel economy and reduction of emissions can be achieved by insulation of the combustion chamber components to reduce heat rejection. However, such insulation will also increase the operating temperature of the piston ring/cylinder liner interface from approximately 150°C to over 300°C. Since existing ring/liner materials cannot withstand these higher operating temperatures alternatives are needed for this critical tribological interface. This paper describes the development of a cost effective ID grinding technique for machining the bores of plasma sprayed diesel engine cylinder liners.

Coolant formulations based on organic acid corrosion inhibitor technology have been tested in over 180 heavy duty engines for a total of more than 50 million kilometers. This testing has been used to document long life coolant performance in various engine types from four major engine manufacturers. Inspections of engines using organic acid based coolant (with no supplemental coolant additive) for up to 610,000 kilometers showed excellent protection of metal engine components. Improved protection was observed against cylinder liner, water pump, and aluminum spacer deck corrosion. In addition, data accumulated from this testing were used to develop depletion rate curves for long life coolant corrosion inhibitors, including tolyltriazole and nitrite. Nitrite was observed to deplete less rapidly in long life coolants than in conventional formulations.

Evaluations of the liner pitting protection performance provided by engine coolant corrosion inhibitors and supplemental coolant additives have presented many problems. Current practice involves the use of full scale engine tests to show that engine coolant inhibitors provide sufficient liner pitting protection. These are too time-consuming and expensive to use as the basis for industry-wide specifications. Ultrasonic vibratory test rigs have been used for screening purposes in individual labs, but these have suffered from poor reproducibility and insufficient additive differentiation. A new test procedure has been developed that reduces these problems. The new procedure compares candidate formulations against a good and bad reference fluid to reduce the concern for problems with calibration and equipment variability. Cast iron test coupons with well-defined microstructure and processing requirements significantly reduce test variability.

Engine cooling fan systems for off-highway machinery require a significant amount of horsepower and contribute to the overall noise level of the machine. Reducing fan speed in times of low cooling demand provides a means to reduce vehicle noise levels and divert engine horsepower from the fan to do productive work. The fan must, however, continue to provide adequate airflow when demanded by the cooling system. Electronic fan controls that modulate fan speed to meet changing cooling system requirements provide the above advantages.

A three dimensional mathematical model of a Caterpillar mining truck has been developed to simulate transient structural deformation and suspension response of a large mining truck traversing a known rough terrain course. The model incorporates compliant (finite element) representations of the truck frame, dump body, and rear axle housing into a dynamic mechanical system simulation model. Model results - frame acceleration, axle housing elastic deformation, and suspension response (strut pressures and displacements) are correlated with measured data from an instrumented truck traversing the steel speed bump portion of the rough terrain course. Results demonstrate that complex truck behavior can be simulated by combining finite element and mechanical system simulations.

Electronics technology has evolved significantly since the first electronically controlled heavy duty on-highway truck engines were introduced in the mid 1980's. Engine control hardware, software, and sensor designs have been driven by many factors. Emissions regulations, fuel economy, engine performance, operator features, fleet management information, diagnostics, vehicle integration, reliability, and new electronics technology are some of those factors. The latest engine electronics technology is not only found in heavy duty on-highway trucks, but in off-highway applications as well. Track-type tractors, haul trucks, wheel loaders, and agricultural tractors now benefit from the advantages of electronic engines. And, many more new applications are being developed.

Catalytic converters have been developed to reduce diesel engine emissions to aid in meeting the 1994 EPA on-highway standards for heavy duty (above 8,500 pound gross vehicle weight) trucks. As converters are made available for on-highway applications, questions inevitably arise as to their applicability to larger off-highway equipment. This paper covers the application of catalytic converters to a Caterpillar 785 off-highway truck operating in a diamond mine in Siberia. Targeted emissions for this application were unburned hydrocarbons (HC) (especially aldehydes), and carbon monoxide (CO). Experience from the on-highway converter development indicated oxidation catalysts could reduce these emissions. This paper addresses the development and selection of a catalytic converter for the 785 truck. Tradeoffs of vehicle modifications vs. catalytic converter performance and design are discussed.

Catalytic converters have become a viable aftertreatment system for reducing emissions from on-highway diesel engines. This paper addresses the development and production qualification of a catalytic converter. The testing programs that were utilized to qualify the converter system for production included emissions performance, emissions durability, physical durability, and field test programs. This paper reports on the specific tests that were utilized for the emissions performance and emissions durability testing programs. An explanation on the development of an accelerated durability test program is also included. The physical durability section of the paper discusses the development and execution of laboratory bench tests to insure the catalytic converter/muffler maintains acceptable physical integrity.

The need to accurately measure and record the payload of large off-highway mining trucks was identified by The Broken Hill Proprietary Co. Ltd. (BHP). In response. Caterpillar designed and developed a system to fufill that need. The payload carried by mine haul trucks has a strong influence on production rates and costs. The system developed should enable payloads to be much better controlled than has been previously possible. The system also provides a number of mine management features. The development of the system is described from the concept stage to the production stage. Final production capabilities of the microprocessor based system are described. Payload measurement capabilities, diagnostic capabilities, data storage, and data extraction methods are discussed.