Search Results

The effect of the ring pack storage mechanism on the hydrocarbon (HC) emissions from an air-cooled utility engine has been studied using a simplified ring pack model. Tests were performed for a range of engine load, two engine speeds, varied air-fuel ratio and with a fixed ignition timing using a homogeneous, pre-vaporized fuel mixture system. The integrated mass of HC leaving the crevices from the end of combustion (the crank angle that the cumulative burn fraction reached 90%) to exhaust valve closing was taken to represent the potential contribution of the ring pack to the overall HC emissions; post-oxidation in the cylinder will consume some of this mass. Time-resolved exhaust HC concentration measurements were also performed, and the instantaneous exhaust HC mass flow rate was determined using the measured exhaust and cylinder pressure.

The contribution of fuel adsorption in engine oil and its subsequent desorption following combustion to the engine-out hydrocarbon (HC) emissions of a spark-ignited, air-cooled, V-twin utility engine was studied by comparing steady state and cycle-resolved HC emission measurements from operation with a standard full-blend gasoline, and with propane, which has a low solubility in oil. Experiments were performed at two speeds and three loads, and for different mean crankcase pressures. The crankcase pressure was found to impact the HC emissions, presumably through the ringpack mechanism, which was largely unaltered by the different fuels. The average and cycle-resolved HC emissions were found to be in good agreement, both qualitatively and quantitatively, for the two fuels. Further, the two fuels showed the same response to changes in the crankcase pressure. The solubility of propane in the oil is approximately an order of magnitude lower than for gasoline.

Planar laser-induced fluorescence (PLIF) has become a useful diagnostic for the quantification of in-cylinder flowfield conditions, and in many applications determining the homogeneity of the in-cylinder flowfield is of primary importance. In some cases, noise associated with this imaging technique (i.e., camera noise, shot-to-shot laser energy variation, and laser sheet profile variations) can dominate the flowfield inhomogeneities, leading to biased mixture stratification statistics. Presented herein are three data normalization schemes (global-, image-, and ray-mean) that can be used to correct for these noise sources when assessing mixture stratification from PLIF data. The normalization schemes are applied to in-cylinder PLIF data obtained over a wide range of inhomogeneity levels, and the conditions over which the use of each normalization scheme is appropriate are discussed.

The mixing between the flows introduced through different intake valves of a four-valve engine was investigated optically. Each valve was fed from a different intake system, and the relative sensitivity to different flow parameters (manipulated with the goal of enhancing the bulk in-cylinder stratification) was investigated. Flow manipulation was achieved in three primary ways: modifying the intake runner geometry upstream of the head, introducing flow-directing baffles into the intake port, and attaching flow break-down screens to the intake valves. The relative merits of each flow manipulation method was evaluated using planar laser-induced fluorescence (PLIF) of 3-pentanone, which was introduced to the engine through only one intake valve. Images were acquired from 315° bTDC through 45° bTDC, and the level of in-cylinder stratification was evaluated on an ensemble and cycle-to-cycle basis using a novel column-based probability distribution function (PDF) contour plot.

The effect of the presence of liquid fuel in the intake manifold on unburned hydrocarbon (HC) emissions of a spark-ignited, carbureted, air-cooled V-twin engine was studied. To isolate liquid fuel effects due to the poor atomization and vaporization of the fuel when using a carburetor, a specially conditioned homogeneous, pre-vaporized mixture system was developed. The homogeneous mixture system (HMS) consisted of an air assisted fuel injection system located approximately 1 meter upstream of the intake valves. The results from carburetor and HMS are compared. To verify the existence of liquid fuel in the manifold, and to obtain an estimate of its mass, a carburetor-mounted liquid fuel injection (CMLFI) system was also implemented. The conditions tested were 10% and 25% load at 1750 RPM, and 25%, 50%, and 100% at 3060 RPM. The results of the comparison show that the liquid fuel in the intake manifold does not have a statistically significant influence on the averaged HC emissions.

A spectroscopic diagnostic system was designed to study the effects of different engine parameters on the chemiluminescence characteristic of HCCI combustion. The engine parameters studied in this work were intake temperature, fuel delivery method, fueling rate (load), air-fuel ratio, and the effect of partial fuel reforming due to intake charge preheating. At each data point, a set of time-resolved spectra were obtained along with the cylinder pressure and exhaust emissions data. It was determined that different engine parameters affect the ignition timing of HCCI combustion without altering the reaction pathways of the fuel after the combustion has started. The chemiluminescence spectra of HCCI combustion appear as several distinct peaks corresponding to emission from CHO, HCHO, CH, and OH superimposed on top of a CO-O continuum. A strong correlation was found between the chemiluminescence light intensity and the rate of heat release.

Particulate mass (PM) emission rate and size distribution measurements were performed in a direct-injection two-stroke engine under a wide range of conditions using a venturi-type mini-dilution tunnel. Air-assisted and nitrogen-assisted liquid fuel injection were both tested to investigate subtle changes in local equivalence ratio; gaseous propane injection using the same injection system was investigated to isolate the effects of liquid fuel impingement. Under overall lean operating conditions the PM emissions were found to decrease when the air-assisted injection was changed to N2-assisted injection with all other parameters equal. The suggested cause for this behavior was a reduction in the PM formation and oxidation rates due to lower local temperatures. A similar effect (lower particulate matter emissions with a locally richer air-fuel ratio) was observed for a light load condition where the local oxygen concentration was varied by changing the exhaust gas recirculation rate.

Valve deactivation followed by multiple compression-expansion strokes was employed to remove intake-generated turbulence from the bulk gas in an internal combustion engine. The result was a nearly quiescent flowfield that retains the same time-varying geometry and, to a first approximation, thermodynamic conditions as a standard engine. Mass loss, and more significantly heat loss were found to contribute to a reduction in the peak cylinder pressure in the cycle following two compression-expansion strokes. The reduction of the turbulence was verified both computationally and by performing premixed combustion studies. Mixing studies of both liquid spray jets and gaseous jets were performed. Laser-induced fluorescence images of high spatial resolution and signal-to-noise ratio were acquired, allowing the calculation of the two in-plane components of the scalar dissipation rate.

Particulate emission measurements were performed on a direct-injection two-stroke engine that employed a lost-oil lubricating system. The particulate emissions were sampled using a partial-flow dilution system. Particulate mass emission rates were measured using a tapered element microbalance (TEOM), and the results were found to compare favorably with gravimetric tests performed simultaneously. The size distribution was measured using a scanning mobility particle sizer (SMPS), and the cumulative mass from the measured size distribution was found to agree well with the values measured by the TEOM. The particulate mass emission were found to be dominated by particulate matter derived from the engine oil. The particulate emissions were found to decrease substantially as the oil flow to the engine was reduced from the baseline case of 1:100 (oil-to-fuel mass ratio).

Combustion under stratified operating conditions in a direct-injection spark-ignition engine was investigated using simultaneous planar laser-induced fluorescence imaging of the fuel distribution (via 3-pentanone doped into the fuel) and the combustion products (via OH, which occurs naturally). The simultaneous images allow direct determination of the flame front location under highly stratified conditions where the flame, or product, location is not uniquely identified by the absence of fuel. The 3-pentanone images were quantified, and an edge detection algorithm was developed and applied to the OH data to identify the flame front position. The result was the compilation of local flame-front equivalence ratio probability density functions (PDFs) for engine operating conditions at 600 and 1200 rpm and engine loads varying from equivalence ratios of 0.89 to 0.32 with an unthrottled intake. Homogeneous conditions were used to verify the integrity of the method.

Bulk gas temperature in an HCCI engine was measured using a novel optical sensing technique. A wavelength-agile absorption sensor using a fiber-coupled LED was used to measure the in-cylinder gas temperature. H2O absorption spectra spanning 1380-1420nm were recorded once every 63 μs using this sensor. The gas temperature was inferred from a least-squares fit of the integrated absorbance areas of H2O absorption features in this spectral region to those from simulated spectra. The primary source of the H2O was the humidity in the intake air. Measurements were made during the compression and early portion of the combustion phase of an n-heptane fueled HCCI engine. The measured pressure-temperature history was compared to kinetic calculations of the ignition delay, and showed the traversal of the negative temperature coefficient regime.

Vapor concentration measurements were performed for two unit injectors typically found in small- and medium-bore applications under evaporating conditions similar to those experienced in Diesel engines. Ambient gas temperatures of 800 and 1000 K and an ambient density of 15 kg/m3 were investigated using a constant volume combustion-type spray chamber. The exciplex laserinduced fluorescence technique with TMPD/naphthalene doped into the fuel was used to quantitatively determine the vapor-phase concentration and liquid-phase extent. The vapor-phase concentration was quantified using a previously developed method that includes corrections for the temperature dependence of the TMPD fluorescence, laser sheet absorption, and the laser sheet intensity profile. The effect of increasing ambient temperature (1000 vs. 800 K) was significant on intact liquid length, and on the spray-spreading angle in the early portion of the injection period.

The noise characteristics of four camera systems representative of those typically used for laser-imaging experiments (a back-illuminated slow-scan camera, a frame-straddling slow-scan camera, an intensified slow-scan camera and an intensified video-rate camera) were investigated, and the results are presented as a function of the signal level and illumination level. These results provide the maximum possible signal-to-noise ratio for laser-imaging experiments, and represent the limit of quantitative signal interpretation. A calibration strategy for engine data that limits the uncertainties associated with thermodynamic and optical correction was presented and applied to engine data acquired with two of the camera systems. When a rigorous analysis of the signal is performed it is seen that shot noise limits the quantitative interpretation of the data for most typical laser-imaging experiments, and obviates the use of single-pixel data.

To experimentally investigate evaporating sprays under conditions experienced in high speed direct-injection (HSDI) diesel engines, the exciplex LIF technique with the TMPD / naphthalene dopant system was applied in a combustion-type constant-volume spray chamber. The chamber allows spark ignition of a slightly rich C2H2-air mixture, and subsequent fuel injection into the high temperature and pressure products. A detailed set of calibration experiments has been performed in order to quantify the TMPD fluorescence signal. It has been demonstrated that the TMPD fluorescence intensity is directly proportional to concentration, is independent of the chamber pressure, and was not sensitive to quenching by either water vapor or carbon dioxide. Therefore, the temperature dependence of the TMPD fluorescence was the only correction factor required for quantitative measurements. Using a dual heated-jet experiment, the temperature dependence of TMPD fluorescence up to 1000 K was measured.

The effects of augmented mixing through the use of an auxiliary gas injection (AGI) were investigated in a direct-injection gasoline engine operated at a 22:1 overall air-fuel ratio, but with retarded injection timing such that the combustion was occurring in a locally rich mixture as evident by the elevated CO emissions. Two AGI gas compositions, nitrogen and air, were utilized, the gas supply temperature was ambient, and a wide range of AGI timings were investigated. The injected mass was less than 10% of the total chamber mass. The injection of nitrogen during the latter portion of the heat release phase resulted in a 25% reduction in the CO emissions. This reduction is considered to be the result of the increased mixing rate of the rich combustion products with the available excess air during a time when the temperatures are high enough to promote rapid oxidation.

Time-resolved measurements were made of the gas composition at the exhaust port of a direct-injection two-stroke engine operating at 2000 rpm and an air-fuel ratio of 30:1. A high-speed sampling valve capable of 1.0 ms (12 CAD) time resolution was used to collect samples 1 cm downstream of the exhaust port of the engine. The time-resolved NOx, CO2 and CO concentrations decreased continuously during the scavenging process due to the dilution by short-circuited air. The hydrocarbon emissions, however, behaved significantly differently from the other species. At the time of exhaust port opening the concentration was low, it reached a maximum value by BDC, then decreased slightly in the latter part of the scavenging event. The dilution rates calculated for the hydrocarbon data gave negative values, indicating that there was a significant production of hydrocarbons during the gas exchange period.

Engine tests were conducted to study the effect of fuel-air mixture preparation on the combustion and emission performance of a two-stroke direct-injection engine. The in-cylinder mixture distribution was altered by changing the injection system, injection timing, and by substituting the air in an air-assisted injector with nitrogen. Two injection systems which produce significantly different mixtures were investigated; an air-assisted injector with a highly atomized spray, and a single-fluid high pressure-swirl injector with a dense penetrating spray. The engine was operated at overall A/F ratios of 30:1, where stratification was necessary to ensure stable combustion; and at 20:1 and 15:1 where it was possible to operate in a nearly homogeneous mode. Moderate engine speeds and loads were investigated. The effects of the burning-zone A/F ratio were isolated by using nitrogen as the working fluid in the air-assist injector.

The role of mixture stratification on combustion rate has been investigated in a constant volume combustion vessel in which mixtures of different equivalence ratios can be added in a spatially and temporally controlled fashion. The experiments were performed in a regime of low fluid motion to avoid the complicating effects of turbulence generated by the injection of different masses of fluid. Different mixture combinations were investigated while maintaining a constant overall equivalence ratio and initial pressure. The results indicate that the highest combustion rate for an overall lean mixture is obtained when all of the fuel is contained in a stoichiometric mixture in the vicinity of the ignition source. This is the result of the high burning velocity of these mixtures, and the complete oxidation which releases the full chemical energy.

Planar instantaneous fuel concentration measurements were made by laser-induced fluorescence of 3-pentanone in the spark gap just prior to ignition in a direct-injection spark-ignition engine operating at a light load, highly stratified condition. The distribution of the average equivalence ratio in a circle of 1.9 mm diameter centered on the spark plug showed that a large fraction of the cycles had an equivalence ratio below the lean limit, yet acceptable combustion was achieved in those cycles. Further, weak correlation was found between the local average equivalence ratio near the spark plug and the time required to achieved a 100 kPa pressure rise above the motoring pressure, as well as other parameters which characterize the early stages of combustion. The cause for this behavior is assessed to be mixture motion during the spark discharge which continually convects fresh mixture through the spark gap during breakdown.

Simultaneous fuel distribution images (by shadowgraph and laser-induced fluorescence) and cylinder pressure measurements are reported for a combusting stratified-charge engine with a square cup in the head at 800 RPM and light load for two spark locations with and without swirl. Air-assisted direct-injection occurred from 130°-150° after bottom dead center (ABDC) and ignition was at 148° ABDC. The engine is ported and injection and combustion take place every 6th cycle. The complicated interaction of the squish, fuel/air jet, square cup, spark plug geometry and weak tumble gives rise to a weak crossflow toward the intake side of the engine with no swirl, but toward the exhaust side in the presence of strong swirl, skewing the spray slightly to that side.