Search Results

For metrological traceability of pressure sensors, static calibration procedures are standard. If these sensors are used in dynamic systems, unexpected phenomena or deviations occur in the recorded signal characteristics. By setting up a dynamic pressure calibration facility, it is possible to investigate this dynamic behavior and learn about the interactions between sensor and investigated system. To be able to identify the disturbing influences and interactions occurring during calibration and in subsequent measurement use, it is necessary to increase the existing understanding of the system. In the context of the contribution, the calibration procedure used, its properties such as repeatability, reproducibility as well as the system interaction of the influencing variables are analyzed. Special attention is paid to the effects of varying gas content in the calibration medium, its influence on the system and on the observed phenomena occurring.

Knocking is still one of today’s major limitations regarding efficiency-increasing measures for SI combustion engines. Due to the complex stochastic nature of the phenomenon, not only prediction and consideration within the engine development is of relevance. A further challenge is control of the phenomenon during engine operation, with the aim of maximizing the efficiency while preventing engine damage and maintaining the driver comfort. Conventional knock control is characterized by detecting knock events and subsequently adjusting the spark timing depending on whether knock was detected. This paper proposes a new knock control concept based on the prediction and direct control of the knock frequency, compared to the conventional reactive and indirect control of the knock frequency. For the prediction of the knock frequency, a calculation approach based on three different parameters is utilized.

The reduction of engine-out emissions and increase of the total efficiency is a fundamental approach to reduce the fuel consumption and thus emissions of vehicles driven by combustion engines. Conventional passenger cars are operated mainly in lower part loads for most of their lifetime. Under these conditions, oil temperatures are far below the maximum temperature allowed and dominate inside the journal bearings. Therefore, the objective of this research was to investigate possible potentials of friction reduction by optimizing the combustion engine’s thermal management of the oil circuit. Within the engine investigations, it was shown that especially the friction of the main and connecting rod bearings could be reduced with an increase of the oil supply temperature. Furthermore, on a journal bearing test rig, it was shown that no excessive wear of the bearings is to be expected in case of load increase and simultaneous supply of cooler oil.

Variation of the geometric compression ratio in gasoline combustion engines during engine operation enables potential for decreasing fuel consumption as well as emissions. One way to achieve a variable geometric compression ratio (VCR) is the application of a connecting rod with a variable effective length between its large end and its small end. Such a system consists of a connecting rod body with an eccentrically supported piston pin and a linkage which is supported hydraulically. Therefore, the connecting rod evolves from a solid part to a complex assembly of mechanical and hydraulic parts. In order to deploy this system in the most efficient way, an understanding of the physics and the dynamic behavior of the VCR connecting rod is necessary. This includes the mechanical subsystem as well as the hydraulic subsystem. This paper describes the experimental examination of a two stage variable connecting rod.

In this paper a rule-based energy management for parallel hybrid electric vehicles (HEVs) is presented, which is based on the principles describing the optimal control behavior. Therefore we first show the general relations that can be used to describe the optimal limit of electric driving as well as the optimal torque split among the two propulsion systems. Subsequently these relations are employed to derive maps, which represent the optimal behavior depending on several input parameters. These maps are then used as inputs for the rules in the proposed energy management. This not only makes it possible to automatically calibrate the rule-based controller but also gives the optimal control in every driving situation. Given it is not fuel-efficient to turn the internal combustion engine (ICE) on or off for short intervals, it is further shown how this approach allows to adjust the established limit for electric driving by additional rules.

In the last years motorsport is facing a technical revolution concerning the engine technology in every category, from touring car championships up to the F1. The strategy of the car manufacturers to bring motorsport engine technology closer to mass production one (e.g. turbo-charging, downsizing and direct injection) allows both to reduce development costs and to create a better image and technology transfer by linking motorsport activities to the daily business. Under these requirements the so-called Global Race Engine (GRE) concept has been introduced, giving the possibility to use one unique engine platform concept as basis for different engine specifications and racing categories. In order to optimize the performance of this kind of engines, especially due to the highly complex mixture formation mechanisms related to the direct injection, it is nowadays mandatory to resort to reliable 3D-CFD simulations.

To demonstrate the potential of a CO2-minimized propulsion concept a study of a natural-gas, micro-hybrid powertrain was carried out. The basis was built by experimental investigations of a turbocharged 1.0-l, 3-cylinder engine operated at stoichiometric and lean air/fuel ratio with EGR and an optimized combustion strategy. With the results of this study a still existing model for micro-hybrid vehicles was filled and the CO2 emissions for several concepts were calculated. It could be shown that CO2 improvements of 30 to 40% for the IC engine and up to 50% for the complete micro-hybrid propulsion system accompanied with better driveability are possible.