Search Results

The exhaust system design and development need to be more flexible and easily adaptable for the requirement of dynamic changes to meet the upcoming emission and noise regulations. Durability of exhaust system components are evaluated through conventional bending moment testing using specified standard load conditions. Road load re-production test is an improvement of the conventional approach to predict component weld durability. It involves the systematic and sequential process of acquiring road load data such as sensor instrumentation, strain measurement at the test track, data processing and input to Bi-Ax testing. S/N Curve testing is introduced recently as an alternate method to minimize the use of road load reproduction testing. It involves prediction of rough force using transient response analysis followed by Bi-Ax testing for the derived high and low load forces to meet the target number of cycles to failure.

While advanced automotive system assemblies contribute greater value to automobile safety, reliability, emission/noise performance and comfort, they are also generating higher temperatures that can reduce the functionality and reliability of the system over time. Thermal management and proper insulation are extremely important and highly demanding for the functioning of BSVI and RDE vehicles. Frugal engineering is mandatory to develop heat shield in the exhaust system with minimum heat loss. Heat shield design parameters such as insulation material type, insulation material composition, insulation thickness, insulation density, air gap thickness and outer layer material are studied for their influences on skin temperature using mathematical calculation, CFD simulation and measurement. Simulation results are comparable to that of the test results within 10% deviation.

Tube bends are critical in an exhaust system. The acceptability of tube bends is based on the induced level of shape imperfections considered. An analysis is presented for the performance tuning of the genetic algorithm including the importance of raw material selection, ovality and elongation property. This study is an attempt to analyze the ovality effect of STAC 60/60 material. CAE tools are essential to exploit the design of experiments and find out the optimum values of the design parameters in comparison with full factorial designs. Especially the effects of materials, dimensions and geometry shape of the ultimate strength were discussed by both CAE and experiments. The ultimate strength of steel tube was evaluated at least 20-30% as a local strain independent of the materials. The dependency of ultimate bending angle on original centre angle of the tube bend was clarified.

Automotive exhaust system components are exposed to many types of vibrations, from simple sinusoidal to maximum random excitations. Computer-Aided engineering (CAE) plays an inevitable role in design and validation of hot vibration shaker assembly. Key Life Test (KLT), an accelerated hot vibration durability test, is established to demonstrate the robustness of a catalytic converter. The conditions are chosen such a way that the parts which passes key life test will always pass in the field, whereas the parts which fail in the key life test need not necessarily fail in the field. The hot end system and the test assembly should survive in these aggressive targeted conditions. The test fixture should be much more robust than the components that it should not fail even if the components fail. This paper reveals the computational methodology adopted to address the design, development and validation of the test assembly.

This paper provides elastic analysis of compressive stresses in the matrix and skin regions of automotive substrates during 3D- and 2D-isostatic strength testing. The matrix region is treated as transversely isotropic material and the skin region as isotropic material, each with their independent elastic properties. Such a solution helps quantify load sharing by the matrix and skin regions which, in turn, affect compressive stresses in each region. The analysis shows that the tangential compressive stresses in the skin and matrix differ significantly at the interface due to high stiffness ratio of skin versus matrix. The resulting strain in the skin is more severe for thin and ultrathin wall substrates and may lead to localized bending of interfacial cells thereby inducing premature failure. Methods to reduce compressive strain in both the matrix and skin without affecting performance-related advantages are discussed.

The oven shock test is an accelerated test which is often used to quantify the thermal durability of both coated and uncoated ceramic substrates. The test calls for heating the substrate for 30 minutes in an oven, which is preheated to specified temperature, and then cooling it in ambient environment for 30 minutes. Such a cycle induces axial and tangential stresses, during cooling, in the skin region whose magnitude depends on physical properties, oven temperature, radial temperature gradient and the aspect ratio of substrate. In addition, these stresses vary with time; their maximum values occur as soon as the substrate is taken out of the oven. This paper evaluates the severity of thermal stresses as function of above factors and estimates the probability and mode of failure during cooling using thermocouple data. Methods to reduce these stresses are discussed.

As emissions regulations become more stringent, catalyst supports with higher cell density, smaller wall thickness, higher surface area and lower thermal mass become more desirable for faster light off and higher conversion efficiency. Simultaneously, however, washcoat formulation and loadings have to be adjusted to yield higher and more stable B.E.T. area at operating temperatures representative of close-coupled application. The thermal mass contribution of advanced washcoat system to catalyst supports with 600/4 and 900/2 cell structures may approach or even exceed that of uncoated substrates. Under such high washcoat loadings, the composite properties of advanced catalysts may be affected adversely in terms of their physical durability, notably in close-coupled application. This paper focuses on potential solutions to light-off performance and FTP efficiency, via optimization of substrate/washcoat interaction, geometric design and the mounting system.

Stringent emissions legislation for diesel-powered vehicles, soon to go into effect, has led to new advances in both Diesel Oxidation Catalysts (DOC) and Diesel Particulate Filters (DPF). This paper reviews some of the new developments in DOC support design which lead to improved light-off behavior and higher overall emissions performance through lower thermal mass, higher Geometric Surface Area (GSA) and larger Open Frontal Area (OFA) than those afforded by the standard cordierite 400/6.5 cell configuration. The four different DOC supports examined in this paper include 400/4, 200/8, 300/8 and 400/6.5 - the last one serving as baseline.

Tempered float glass is commonly used for both side windows and backlites in the automotive industry. The success of such products is primarily attributed to high level of residual compression, following tempering, which provides abrasion resistance as well as 3X higher functional strength to sustain mechanical, vibrational and thermal stresses during the vehicle's lifetime. Certain applications of tempered glass, however, require mounting holes whose surface-finish must be controlled carefully to withstand transient tensile stresses during tempering. Simultaneously, the nature and magnitude of residual compression at the hole must provide sufficient robustness to bear mounting, vibrational and thermal stresses throughout the life of the vehicle. This paper presents (i) analysis of residual compression at the hole, (ii) measurement of biaxial strength of annealed glass with hole at center, and (iii) measurement of biaxial strength of tempered glass with hole at center.

Conventional catalytic converter developments driven by trial and error attempts by experts who successfully employ heuristics (a set of empirical rules gained through time and experience) will not be able to meet the current demanding needs. The cost and time involved in testing every catalytic converter mandates new approaches aimed at improving efficiency and reducing development lead time. Computational tools such as HeatCad, P-Cat, CatHeat, WAVE, Computational Fluid Dynamics (CFD), Finite Element Analysis (FEA) and Monte-Carlo simulation are sequentially applied to design, optimize and manufacture catalytic converter. Heatcad analysis provides the way to identify thermal management issues and to optimize runner lengths and material thickness of the manifold, and downpipes. P-Cat is used to estimate back pressure due to substrates, washcoat, end cones, and inlet/outlet pipes. CatHeat analysis is used to predict the temperature profile across the converter.

Typically, the maximum converter skin temperature occurs when the catalytic converter is in the cool down process after the engine is shut-off. This phenomenon is called temperature soaking. This paper proposes a numerical method to simulate this process. The converter skin temperatures vs. time are predicted for the converter cool down process. The soaking phenomenon is observed and the maximum temperature is determined. Temperatures are also predicted for the exhaust gas, substrate, mounting mat and shell of the converter assembly. The numerical results are validated with measurements, and an acceptable correlation is achieved. This study focuses on converters with ceramic substrates; however, this methodology can also be used for converters with metallic substrates.

Stringent emissions standards with 95+% conversion efficiency requirements call for advanced ceramic catalyst supports with thinner walls, higher cell density and optimum cell shape. The extrusion technology for cellular ceramics has also made significant progress which permits the manufacture of advanced catalyst supports. Similarly, modifications in cordierite chemistry and the manufacturing process have led to improved microstructure from coatability and thermal shock points of view. The design of these supports, however, requires a systems approach to balance both the performance and durability requirements. Indeed as the wall gets thinner, the contribution of washcoat becomes more significant in terms of thermal mass, heat transfer, thermal expansion, hydraulic diameter and structural stiffness - all of which have an impact on performance and durability. For example, the thinner the wall is, the better the light-off performance will be.

Single seam stuffed converters are often used to house ceramic substrates due to the simplicity and low tooling cost of the canning process. However, stuffing thinwall substrates requires careful GBD (gap bulk density) control because of their low isostatic strengths. Statistical simulation results indicate that the stuffing process can be performed within the required GBD range of 0.8 to 1.2 g/cm3 using vermiculite mats with the current tolerance specifications. A nominal value of 0.925 g/cm3 is recommended to minimize substrate breakage. Experimental results show that prototypes can be built with a GBD accuracy of 0.05 g/cm3. This paper describes the requirements needed to design and validate single seam stuffed converters.

The stringent emissions legislation has necessitated advances in the catalytic converter system comprising the substrate, washcoat technology, catalyst formulation and packaging design. These advances are focused on reducing light-off emissions at lower temperature or shorter time, increasing FTP efficiency, reducing back pressure and meeting the mechanical and thermal durability requirements over 100,000 vehicle miles. This paper reviews the role of cordierite ceramic substrate and how its design can help meet the stringent emissions legislation. In particular, it compares the effect of cell geometry and size on performance parameters like geometric surface area, open frontal area, hydraulic diameter, thermal mass, heat transfer factor, mechanical integrity factor and thermal integrity factor - all of which have a bearing on emissions, back pressure and durability. The properties of advanced cell configurations like hexagon are compared with those of standard square cell.

The stringent emissions standards in the late 1990's like NLEV, ULEV and SULEV have led to major modifications in the composition and design of ceramic substrates. These changes have been necessitated to reduce cold start emissions, meet OBD-II requirements, and to ensure 100,000 mile durability requirement in a cost-effective manner. This paper presents the key advances in ceramic substrates which include lower thermal expansion, lighter weight, higher surface area and improved manufacturing process all of which help meet performance requirements. In addition to above benefits, the compressive and tensile strengths of lightweight substrates, as well as their thermal shock resistance, are found to be adequate following the application of high surface area alumina washcoat. The strength properties are crucial for ensuring safe handling of the substrate during coating and canning and for its long term mechanical durability in service.

Stringent emissions standards for HC, CO and NOx have necessitated the development of thin wall ceramic substrates which offer higher surface area, larger open frontal area and lower thermal mass. Such substrates offer the additional benefit of being compact which make them ideal for manifold mounting in the engine compartment. These attributes of ceramic substrates, following washcoat and catalyst application, translate directly into quick light-off, high conversion efficiency and low back pressure. To preserve these advantages at high operating temperature and still meet 100,000 mile vehicle durability, the thermomechanical interaction between the substrate and thin wall washcoat system must be managed carefully via formulation, % loading and the calcination process. This paper presents the physical properties data for thin wall ceramic substrates before and after the washcoat application.

Significant advances in composition and the manufacturing process have led to thin wall cordierite ceramic substrates with low thermal mass, high surface area, and large open frontal area-properties that are critical for fast light-off, high conversion efficiency and low back pressure. Indeed, such substrates are ideal catalyst supports for meeting the ever-stringent emissions regulations, ala SULEV and ULEV, as demonstrated by recent performance data1. This paper focuses on the physical durability of 400/4 and 600/4 cordierite ceramic substrates. In particular, it presents strength, fatigue, and modulus data which influence the mechanical durability. In addition, it presents thermal expansion data which impact the thermal durability. Both of these durabilities are examined as a function of operating temperature.

An advanced three-way converter system with significant improvements in light-off performance, conversion efficiency, thermal stability and physical durability at high operating temperature is described. The converter system is comprised of a light-weight ceramic substrate with high surface area triangular cell structure, a new catalyst formulation with enhanced thermal stability and good substrate compatibility, and a durable packaging design which together lead to consistent improvements in high temperature performance and durability. Experimental data including FTP performance, canning trials, and high temperature vibration and thermal shock tests for both the advanced and standard three-way converter systems are presented.

The monolithic, large frontal area (LFA), extruded ceramic substrates for diesel flow-through catalysts offer unique advantages of design versatility, longterm durability, ease of packaging and low Cost [1, 2]*. This paper examines the effect of cell density and cell size on catalyst light-off performance, back pressure, mechanical and thermal durability, and the steady-state catalytic activity. The factors which affect these performance characteristics are discussed. Certain trade-offs in performance parameters, which are necessary for optimum systems design, are also discussed. Following a brief discussion of design methodology, substrate selection, substrate/washcoat interaction and packaging specifications, the durability data for ceramic flow-through catalysts are summarized. A total of over 18 million vehicle miles have been successfully demonstrated by ceramic LFA catalysts using the systems design approach.

Ceramic preconverters have become a viable strategy to meet the California LEV and ULEV standards. To minimize cold start emissions the preconverter must light-off quickly and be catalytically efficient. In addition, it must also survive the more severe thermomechanical requirements posed by its close proximity to the engine. The viability of the ceramic preconverter system to meet both emissions and durability requirements has also been reported recently(1,2). This paper further investigates the impact preconverter design parameters such as cell density, composition, volume, and catalyst technology have on emissions and pressure drop. In addition, different preconverter/main converter configurations in conjunction with electrically heated catalyst systems are evaluated. The results demonstrate that ceramic preconverters substantially reduce cold start emissions. Their effectiveness depends on preconverter design and volume, catalyst technology, and the system configuration.