Search Results

Copper-free NAO disc pads of passenger cars were investigated for a combination of prior braking conditions and moisture adsorption influencing in-stop friction and noise during low-speed stops, and in-stop-friction during moderate-speed stops. Prior braking conditions and moisture adsorption strongly influence subsequent in-stop friction behavior and noise at room temperature. The low-speed in-stop friction behavior looks totally different from that of moderate-speed stops. The low-speed in-stop friction increasingly oscillates with increasing moisture adsorption and goes down towards the end of a stop, which is accompanied by increasing low-frequency noise. The moisture content needs to be quantified/specified to obtain repeatable/reproducible brake test results as the moisture is an unintended and uncontrolled ingredient of a friction material. As the disc surface roughness increases due to prior braking conditions, the friction coefficient of low-speed stops is found to decrease.

The moisture adsorption kinetics of copper-free brake pads was studied to confirm an earlier finding that the adsorption weight gain follows a logarithmic relationship with respect to the square root of humidity exposure time and the relationship is linear in the beginning. When the pad cure temperature was raised from 120 to 180 and 240 °C, the adsorption rate increased. The 180 °C cure produced the highest pad modulus. With increasing moisture adsorption, the pad compression modulus increased just like the pad dynamic modulus, meaning decreasing compression/compressibility while the ISO ‘compressibility’ determined after 3 compressions under 160 bars increased in contradiction. It is concluded that the ISO ‘compressibility’ is a destructive hardness measurement like the Gogan or Rockwell hardness: the key difference is the indenter covers the entire surface of the pad. The true compressibility must be determined as an inverse function of bulk modulus.

The kinetics of moisture adsorption is studied for copper-free brake pads. The pad weight gain is found to increase linearly with the square root of exposure time to humidity at a given temperature in the initial stage of adsorption - the higher the humidity, the higher the weight gain. Pads cured at 150°C adsorb less moisture than pads cured at 220°C. As the moisture content in the pad increases, the tangent modulus increases while the secant modulus decreases, resulting in decreasing compressibility associated with the tangent modulus of compression and increasing compressibility associated with the secant modulus of compression - compressibility defined as a reciprocal of compression modulus. Static modulus of compression, dynamic modulus of compression and hardness measurements are compared, and they all show the same trend. A rate constant of adsorption is proposed to define and compare moisture sensitivity of friction material

The moisture sorption-desorption kinetics of copper-free brake pads was studied in detail. The sorption-desorption behavior is dependent on the environmental temperature and humidity. At 24 °C under 54% RH, the sorption increases rapidly for a week or so identified as the first stage of sorption, enters the second stage of negligible weight gain for a month and then the third stage of rapid sorption again. With increasing moisture sorption, the pad thickness increases through the 3 stages and the dynamic modulus also increases through the 3 stages. Friction materials lose moisture rapidly at 130°C and behave like desiccants. The sorption-desorption phenomenon significantly influences the friction coefficient -- a higher moisture content leading to lower friction coefficients. It is demonstrated that the rising friction coefficient for the half a dozen braking stops at the beginning of every brake testing in general is due to moisture desorption caused by rising pad temperatures.

Earlier publications have demonstrated that pad and disc properties change during storage and also during the SAE J2522 Brake Effectiveness Test Procedure. The current investigation was undertaken to find out how the properties change under milder braking conditions, using the SAE J2707 Wear Test Procedure. A copper-free formulation was selected for the investigation and tested on an inertia dynamometer using a front caliper designed for a passenger car. The pad dynamic modulus changed up or down throughout the test, depending on the test conditions. The pad dynamic modulus, the pad natural frequencies and the disc natural frequencies all decreased by the end of the test. Under high-speed, high-deceleration and high-temperature braking conditions, the pad surface region permanently expands, which results in reduced dynamic modulus and also leads to reduced pad thickness loss as compared with pad weight loss.

Copper-free disc pads of 9 different compositions were made using a traditional hot molding process and tested to study frictional behavior. It is found that the friction coefficient consists primarily of two parts; one part controlled by the plastic deformation of the friction surface region of the disc and pad, and the second part controlled by the total wear of the disc and pads. As the plastic deformation and the wear are non-linear with respect to the load and sliding speed, the friction coefficient becomes a non-linear function of the load and speed. Under moderate braking conditions, the plastic deformation part is more significant in determining the friction coefficient while under more severe braking conditions, the wear contribution becomes more significant. The frictional behavior of a fade cycle is explained, and the correlation between brake squeal and disc wear is confirmed.

The current investigation was undertaken to find out if lighter-weight passenger car disc pads would exhibit wear behaviors similar to pickup truck pads and commercial heavy truck drum linings in terms of the permanent volume expansion of the friction material contact surface region. 2 high-copper NonAsbestos Organic formulations and 3 copper-free LowMet formulations were tested according to the SAE J2522 test procedure. In all cases, the measured pad thickness loss was found to be less than the thickness loss calculated from the weight loss, indicating pad volume expansion in the pad surface region, in full agreement with the results from the pickup truck and heavy trucks. The heataffected swollen/expanded layer ranges from 0.27 to 0.61 mm in thickness depending on the formula and test conditions. Due to the expansion, pad durability projections made from test results based on high temperature city traffic tests can result in underestimating the actual durability.

Earlier publications show that brake pad physical properties such as hardness, modulus and natural frequencies continue to increase at room temperature over a period of 12 months and that the changes are faster during the first 3 - 6 months. The current investigation was undertaken to see how the properties might change during testing for the pads as well as for the discs. Low-copper and copper-free formulations were tested on pickup truck and passenger car brakes. In all cases, the dynamic modulus and natural frequencies are found to decrease (not increase) after the SAE J2522 performance testing, indicating that the stiffness of the pad and that of the disc decrease faster than the mass loss due to wear. Also, the inboard pad and the outboard pad change at two different rates.

Heavy truck brake blocks are found to swell (or expand) permanently during testing or usage, especially so at high temperatures, thus leading to longer durability as measured by thickness loss, similar to light vehicle disc pads. This swelling phenomenon occurs continuously in the layer adjacent to the friction surface during testing or usage; not a one time event. The thickness loss estimated from the weight loss is always greater than measured thickness loss. Brake block wear does not increase linearly with increasing normal load, and the load-sensitivity of block wear is very much dependent on the products. A new test procedure has been developed for generating friction-vs.-temperature and wear-vs.-temperature data at a constant temperature employing intermittent braking on the Chase Brake Lining Quality Tester (SAE J661) and friction material wear can be compared on equivalent-work basis.

It is widely believed or speculated that higher pad compressibility leads to reduced brake squeal and that caliper design can affect brake squeal. After encountering anecdotal contradictory cases, this investigation was undertaken to systematically generate basic data and clarify the beliefs or speculations. In order to adjust pad compressibility, it is common to modify pad molding temperatures, pressures and times, which in addition to changing the compressibility, changes friction coefficient and physical properties of the pad at the same time. In order to separate these two effects, NAO disc pads were prepared under the same molding conditions while using different thicknesses of the underlayer to achieve different compressibilities, thus changing the compressibility only without changing the friction coefficient and physical properties of the pad.

The dynamics and, in particular, the NVH phenomena in brakes are still in the focus of research. Recent investigations of for example Rhee et al. show two principal vibrational forms of the linings on the rotor [1]. The first form is characterized by vibrations where both linings are in-phase (minimal differential torque between the inner pad and the outer pad). This produces in-plane vibrations of the rotor and results in high-frequency squealing events in the brake. The second form is an antiphase vibration of the brake linings with respect to each other (increased differential torque between the inner pad and the outer pad). This produce directly out-of-plane vibrational modes of the disc, which results in lower-frequency caliper and rotor oscillations. One hypothesis is that different wear densities of the linings essentially characterize the two vibrational modes. The wear behavior is not taken into consideration of this paper as it will be discussed in further publications.