Search Results

The paper discusses the process of developing an SAE damping measurement test method that is suitable for testing bars that are not made of steel or are difficult to measure with the traditional Oberst bar method. The method is based on measuring mechanical impedance (force over velocity) of a vibrating bar. The bar is excited at the center using a shaker and hence it is also called a CenterPoint method. The paper discusses the round robin tests that have been conducted so far and discusses the test results that will help develop the standard. The paper discusses the variability of the round robin test results within a laboratory, between laboratories, as well as the coefficient of variation for these measurements. The paper also discusses various parameters that should be carefully monitored in this study, that otherwise could affect the precision of the test procedure.

Laminated steel body panels are used in different applications in vehicles, such as dash panels and wheel wells. A part made out of laminated steel has the potential to provide structure-borne noise reduction and also improve the airborne noise reduction of the part compared to a monolithic part. The use of laminated steel has been more critical when there are deep draws on the part as the deep draws cause localized resonances which degrade the acoustic performance significantly. However, due to lightweighting demands, hybrid laminated panels, commonly known as acoustic patch laminates have become very attractive. This paper discusses the damping and sound transmission loss performances of a dash panel part with monolithic, laminated, and acoustic patch panels.

Standards organizations develop standards depending on the need in the market place. With the change in vehicle design, lightweighting structures, and body panels made out of aluminum and composites, SAE’s Acoustical Materials Committee is developing a new damping standard. This standard is also very suitable in determining the damping performance of materials used in the off-highway applications, where the thickness of the steel body panel is much greater than in the automotive application. The general methodology of this standard is based on the mechanical impedance measurement method and has been developed with the general consensus of automotive engineers, suppliers, and independent test laboratories. This method is essentially based on the fact that a bar is excited at the center by a shaker. The force exerted by the shaker and the corresponding vibration is measured at that point to determine the frequency response function of the mechanical impedance signal.

This paper provides an overview of a custom software developed to obtain measurement data in a self-contained acoustic test facility system used for conducting random incidence sound absorption tests and sound transmission loss tests on small samples in accordance with SAE J2883 and J1400 standards, respectively. Special features have been incorporated in the software for the user to identify anomalies due to extraneous noise intrusion and thereby to obtain good data. The paper discusses the thoughts behind developing user-friendly algorithms and graphical user interfaces (GUI) for the sound generation, control, data acquisition, signal processing, and identifying anomalies.

Traditionally, the damping performance of a visco-elastic material is measured using the Oberst bar damping test, where a steel bar is excited using a non-contacting transducer. However, in an effort to reduce the weight of the vehicles, serious effort is put in to change the body panels from steel to aluminum and composite panels in many cases. These panels cannot be excited using a non-contacting transducer, although, in some cases, a very thin steel panel (shim) is glued to the vibrating bar to introduce ferrous properties to the bar so it can be excited. In the off highway vehicles, although the panels are made of steel, they are very thick and are difficult to excite using the Oberst bar test method. This paper discusses a measurement methodology based on mechanical impedance measurements and has the potential to be a viable/alternate test method to the Oberst bar testing. In the impedance method, the test bar is mounted to a shaker at the center (Center Point method).

Most of NVH related issues start from the vibration of structures where often the vibration near resonance frequencies radiates the energy in terms of sound. This phenomenon is more problematic at lower frequencies by structureborne excitation from powertrain or related components. This paper discusses a laboratory based case study where different visco-elastic materials were evaluated on a bench study and then carried on to a system level evaluation. A body panel with a glazing system was used to study both airborne and structureborne noise radiation. System level studies were carried out using experimental modal analysis to shift and tune the mode shapes of the structure using visco-elastic materials with appropriate damping properties to increase the sound transmission loss. This paper discusses the findings of the study where the mode shapes of the panel were shifted and resulted in an increase in sound transmission loss.

The performance of damping materials is generally evaluated by experimental methods. However most damping materials used in the transportation industry cannot be excited by itself. Therefore, the measurements are generally made by exciting a damped system, where the damped system extends from a bar to a panel. The paper reviews various damped systems and excitation methodologies and discusses some of the limitations of a bar to study the damping performance for different applications. It discusses a methodology where a damped panel is mounted on a fixture and the fixture is excited with a shaker. The paper discusses data acquisition and data reduction procedures to obtain the damping performance of laminated steel acoustic patch products on a third octave band frequency basis.

This paper discusses the thought process that one needs to go through for developing an appropriate sound package treatment for a vehicle. In the development process one needs to put proper emphasis on understanding the source, path, and the receiver system. One needs to have an understanding on how to reduce the noise at the source, path, and/or receiver location. One may need to conduct a feasibility study of the benefits of various noise control options. In terms of sound package treatments one needs to understand the fundamentals of acoustical materials how they work and why one material performs differently than another one, as well as the importance of a well documented specification that every supplier has to meet.

The SAE International standard for testing Oberst bars has been used in the industry for many years with predictable results. Growing interest in testing wider samples to incorporate more of the variability in liquid applied sprayable dampers has led to increased use of a center point damping test method based on a Japanese standard JIS G 0602. This method is similar to that of the ISO 16940 standard for testing laminated glass. Theory shows us that an Oberst test with a free length equal to the half length of a bar used for center point testing will provide the same resonances. This paper intends to show a relationship between the resonances of bars tested with the Oberst and center point test methods. A correlation between the composite loss factor for samples tested with each of the methods will be illustrated.

Random incidence sound absorption measurements of automotive components such as floor carpets, seats, headliners and hoodliners are important during the design and development of noise control treatments in a vehicle. Small volume reverberation rooms [1]1 have been widely used in practice to determine the absorption properties of those components. The SAE Acoustical Materials Committee has organized a task force to develop a standard procedure for measuring random incidence sound absorption properties of flat samples, as well as automotive components in small reverberation rooms. Statistical analysis and correlation study between large reverberation rooms and small reverberation rooms of flat samples using data acquired from a recent round robin study were reported in SAE Paper 2005-01-2284 [2, 3].

This paper discusses a development procedure that was used to evaluate the acoustical performance of one type of dashpanel construction over another type for a given application. Two very different constructions of dashpanels, one made out of plain steel and one made out of laminated steel, were studied under a series of different test conditions to understand which one performs better, and then to evaluate how to improve the overall performance of the inferior dashpanel for a given application. The poorly performing dashpanel was extensively tested with dashmat and different passthroughs to understand the acoustic strength of different passthroughs, to understand how passthroughs affect the overall performance of the dash system, and subsequently to understand how the performance can be improved by improving one of the passthroughs.

An in-vehicle study was conducted to understand how damping treatments on the floor of a vehicle affect the interior sound in the vehicle. Three differently formulated damping treatments were tested on three similar sport utility vehicles for this purpose. Numerous on-road sound and vibration data were collected under different operating conditions, and were reduced to understand the value of the damping treatment in controlling interior noise caused by powertrain and rolling-tire/road interaction. The paper discusses different data analysis procedures that were used in this study to understand whether there is a damping treatment that performs better than others in spite of variances in test vehicles, and still minimize the adverse influence of other variables that are related to the vehicle performance variation itself.

The approaches used to develop an NVH package for a vehicle have changed dramatically over the last several years. New noise and vibration control strategies have been introduced, new materials have been developed, advanced testing techniques have been implemented, and sophisticated computer modeling has been applied. These approaches help design NVH solutions that are optimized for cost, performance, and weight. This paper explains the NVH practices available for use in designing vehicles for the new millennium.

Damping treatments have been used in reducing structure-borne noise in vehicles for many years. Although sheet based heat bondable mastic products (often called melt sheets) are quite common in the industry, sprayable products have several advantages and have been cited in the literature. This paper discusses findings of numerous structure-borne noise studies that were conducted on sprayable materials with different base-chemistries. The analyses show that a waterborne product is the most advantageous damping treatment in an automotive assembly process. The results also reveal that application of this product provides effective damping treatment as well as reduces structurally radiated noise.

This paper provides an overview of sound and sound package (noise control) materials that are used in heavy trucks and buses. Transportation noise is a longstanding and complex problem. The challenge is to have a thorough understanding of the source-path-receiver relationship with respect to the noise generation and propagation such that one can find feasible solutions and applications of noise control materials. This paper discusses different types of noise control materials and also provides some examples of different noise control material applications.

This paper discusses an analytical tool that has been developed to predict what types of interior sound package treatments may be necessary in a truck cab to meet a predetermined target sound level at the driver location. The steps that were taken to develop this tool involved a combination of experimental measurement and analytical based studies. Measurements were conducted to identify the acoustic strengths of the major noise paths through which sound travels from outside to inside the truck. These findings were then used to develop a sound package that reduced the vehicle interior noise to meet the target. Measurements were primarily made on a chassis roll dynamometer with final road verification to substantiate the dynamometer data. Data obtained from these measurements were also used in the analytical model that predicts the impact of various acoustics parts in the vehicle, and has the capability to optimize the sound package treatment in the vehicle.

This paper focuses on the development of treatments to control airborne noise through the dash panel. For a noise control material supplier, these treatments can be the most challenging to design because of the number of pass-throughs and design constraints. The dash panel development process includes extensive in-truck testing and analysis to identify sound paths (location and magnitude) and establish design criteria, laboratory material testing to aid in the selection of appropriate materials, laboratory component testing to select areas requiring treatment and to design the shape of the treatments, and in-truck testing to verify the performance of the new treatments.

Constrained layer damping (CLD) is a well known technique to efficiently damp low frequency vibration. CLD employs a viscoelastic material sandwiched between two very stiff, typically metal, layers. While effective over essentially flat surfaces, CLD has not been applicable to cylindrical shapes. In order to damp low frequency vibration in metal pipes, users have been forced to rely on extensional layer damping, typically consisting of thick layers of extruded or molded rubbers. This paper discusses a novel product to damp cylindrical articles such as metal pipes with a constrained layer heat shrink tubing. This product utilizes a stiff heat shrinkable polymeric jacket bonded on the inside with a viscoelastic layer. When shrunk on a metal pipe or rod, a CLD system is produced. The product is typically thinner than an extensional layer damper and is more effective. It also meets the other physical and environmental requirements for a pipe covering.

A study was conducted to understand the acoustic viability of using post consumer rebond seat foam materials in vehicles for floor carpet underlayment applications. These foam materials were obtained from two different sources: 1) polyurethane foam dismantled from seats of end of life vehicles (ELV or scrap vehicles), and 2) polyurethane foam recovered and cleaned from auto shredder residue (ASR) by the Argonne National Laboratories (ANL) using their cleaning method. The study was conducted using three North-American cars, each serving different market segments. Based on both laboratory and on-road tests conducted on each vehicle, the study concluded that the acoustical performance of the floor carpet underlayment part made of post consumer rebond foam is comparable to that of the current production part mostly made of shoddy materials.

Heat reactive expanding sealer materials are used as acoustical “baffles” to block noise propagation in rails, pillars, posts, and rockers. However, should moisture enter and collect in vertical pillars water damage may occur. Therefore, effort is being made to implement a drainage system for these problem applications. This paper discusses an effective way to prevent water damage by adding an acoustical drain plug to the baffle system with a minimal reduction in acoustical performance. The paper also discusses the performance and the effect of adding this plug to the baffle system. Finally, results of design variations of the plug on the baffle system are reported.