Refine Your Search

Date

Date

Topic

Topic

Author

Author

Test procedures Standard Noise, Vibration, and Harshness (NVH) Interior noise Lasers

Search Results

Viewing 1 to 20 of 8578
123Next >Last >>
Sort by published
Standard

Off-Road Self-Propelled Work Machines Operator Enclosure Environment Part 1: Terms and Definitions
2024-04-23
CURRENT
J3078/1_202404
SAE J3078 provides test methods and criteria for the evaluation of the operator enclosure environment in earth-moving machinery as defined in ISO 6165. SAE J3078/1 gives the terms and definitions which are used in other parts of SAE J3078. It is applicable to Off-Road Self-Propelled Work Machines as defined in SAE J1116 and tractors and machinery for agriculture and forestry as defined in ANSI/ASAE S390.
Standard

Tire Burst Test Methodology
2024-04-17
CURRENT
ARP6265
This document describes a recommended test procedure to assess the burst characteristics of tires used on 14CFR Part 25 or similar transport airplanes.
Standard

Brake Insulator Damping Measurement Procedure
2024-04-02
WIP
J3001
This procedure is applicable to modes from 500 and 13,000 Hz. The parameters measured with this procedure are defined as the damping factor, ξ for first nine vibration modes of the beam. The measurement will be done in free-free conditions and with temperature.
Standard

Nickel Wire and Ribbon 99Ni
2024-04-01
CURRENT
AMS5555G
This specification covers a nickel in the form of round wire and rectangular ribbon.
Standard

Test Method for the Determination of Total Acidity in Polyol Ester and Diester Gas Turbine Lubricants by Automatic Potentiometric Titration
2024-03-18
CURRENT
ARP5088C
The test method describes the procedure for determination of the total acid number (TAN) of new and degraded polyol ester and diester-based gas turbine lubricants by the potentiometric titration technique. The method was validated to cover an acidity range of 0.05 to 6.0 mg KOH g-1. The method may also be suitable for the determination of acidities outside of this range and for other classes of lubricants.
Standard

Test Method for Aerospace Firewall Sealant Flame Penetration
2024-03-18
CURRENT
AS5127/2D
This SAE Aerospace Standard (AS) describes the test methods to determine the flammability performance and capability to control the passage of, and effects from, fire on aircraft firewall sealing compounds. The methods are based on requirements of FAR Part 25, Sections 25.865, 25.867, 25.1191, and 25.1193 and may be used to demonstrate compliance with the requirements established by FAA AC 20-135. This standard shall be used in conjunction with applicable material specifications.
Standard

Motor Vehicle Brake Fluid
2024-03-12
CURRENT
J1703_202403
This SAE Standard covers motor vehicle brake fluids of the nonpetroleum type, based upon glycols, glycol ethers, and appropriate inhibitors, for use in the braking system of any motor vehicle such as a passenger car, truck, bus, or trailer. These fluids are not intended for use under arctic conditions. These fluids are designed for use in braking systems fitted with rubber cups and seals made from styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM).
Standard

Motor Vehicle Brake Fluid Based Upon Glycols, Glycol Ethers, and the Corresponding Borates
2024-03-12
CURRENT
J1704_202403
This SAE Standard covers motor vehicle brake fluids of the nonpetroleum type, based upon glycols, glycol ethers, and borates of glycol ethers, and appropriate inhibitors for use in the braking system of any motor vehicle, such as a passenger car, truck, bus, or trailer. These fluids are not intended for use under arctic conditions. These fluids are designed for use in braking systems fitted with rubber cups and seals made from styrene-butadiene rubber (SBR) or a terpolymer of ethylene, propylene, and a diene (EPDM).
Standard

Brake Insulator Design Guidelines
2024-02-26
WIP
J3317
This document applies to shims only and will outline insulator design guidelines for improved manufacturability, cost and optimized product performance (Durability, bondability…)
Standard

Wheels/Rims - Performance Requirements and Test Procedures Agriculture and Light Construction
2024-02-23
CURRENT
J3229_202402
This SAE Recommended Practice provides the minimum performance requirements and uniform laboratory procedures for fatigue testing of ferrous wheels and demountable rims intended primarily for off road use on agricultural machines (e.g., agricultural tractors, harvesters, trailers, and implements) and light construction machines (e.g., wheel loaders, backhoe loaders, dumpers, mobile excavators, and telehandlers). For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, refer to SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. For wheels intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles, refer to SAE J267. For bolt together military wheels, refer to SAE J1992. This document does not cover other special application wheels and rims.
Standard

Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Xenon-Arc Apparatus
2024-02-23
CURRENT
J2412_202402
This test method specifies the operating procedures for a controlled-irradiance, xenon-arc apparatus used for the accelerated exposure of various automotive interior trim components. Test duration, as well as any exceptions to the specimen preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers. Any deviation to this test method, such as the use of optical filter combinations, is to be agreed upon by contractual parties.
Standard

Wrenches; Flare Nut, Crowfoot, 6- and 12-Point Non-Distorting
2024-01-22
CURRENT
AS4167D
This SAE Aerospace Standard (AS) covers 6-point and 12-point flare nut crowfoot, flare nut wrenches, double end flare nut wrenches, combination box end and flare nut wrenches, combination open end and flare nut wrenches, and ratcheting flare nut wrenches that are designed with the following requirements: (a) non-distorting usage; (b) possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514 and ISO 8434-2; and (c) transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.
123Next >Last >>
X