Search Results

This specification covers a titanium alloy in the form of welding wire (see 8.5).

This specification covers an aluminum alloy in the form of alclad coiled sheet from 0.010 to 0.128 inch (0.25 to 3.25 mm), inclusive, in thickness supplied in the -T4 temper (see 8.5).

This specification covers an aluminum alloy in the form of alclad sheet and plate supplied in the -T861 temper.

This SAE Aerospace Standard (AS)/Minimum Operational Performance Specification (MOPS) specifies the minimum performance requirements of Remote On-Ground Ice Detection Systems (ROGIDS). These systems are ground-based. They provide information that indicates whether frozen contamination is present on aircraft surfaces. Section 1 provides information required to understand the need for the ROGIDS, ROGIDS characteristics, and tests that are defined in subsequent sections. It describes typical ROGIDS applications and operational objectives and is the basis for the performance criteria stated in Section 3 through Section 5. Section 2 provides reference information, including related documents, abbreviations, and definitions. Section 3 contains general design requirements for the ROGIDS. Section 4 contains the Minimum Operational Performance Requirements for the ROGIDS, which define performance in icing conditions likely to be encountered during ground operations.

This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.

This specification covers a nickel in the form of round wire and rectangular ribbon.

This specification covers a corrosion- and heat-resistant steel in the form of welding wire.

This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.

This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings.

This SAE Aerospace Information Report (AIR) covers forced air technology including: reference material, equipment, safety, operation, and methodology. This resource document is intended to provide information and minimum safety guidelines regarding use of forced air or forced air/fluid equipment to remove frozen contaminants. During the effective period of this document, relevant sections herein should be considered and included in all/any relevant SAE documents.

This specification covers a corrosion- and heat-resistant steel in the form of welding wire.

This specification covers a corrosion- and heat-resistant nickel alloy in the form of welding wire.

This specification covers a premium aircraft-quality, corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.

This specification covers an aluminum alloy in the form of extruded bars, rods, wire, shapes, and tubing 5.000 inches (127.00 mm) and under in nominal diameter or least thickness (wall thickness of tubing) (see 8.5).

This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.

SAE Aerospace Recommended Practice ARP1533 is a procedure for the analysis and evaluation of the measured composition of the exhaust gas from aircraft engines. Measurements of carbon monoxide, carbon dioxide, total hydrocarbon, and the oxides of nitrogen are used to deduce emission indices, fuel-air ratio, combustion efficiency, and exhaust gas thermodynamic properties. The emission indices (EI) are the parameters of critical interest to the engine developers and the atmospheric emissions regulatory agencies because they relate engine performance to environmental impact. While this procedure is intended to guide the analysis and evaluation of the emissions from aircraft gas turbine engines (burning conventional hydrocarbon based liquid fuels), the methodology may be applied to the analysis of the exhaust products of any hydrocarbon/air combustor.

The test method describes the procedure for determination of the total acid number (TAN) of new and degraded polyol ester and diester-based gas turbine lubricants by the potentiometric titration technique. The method was validated to cover an acidity range of 0.05 to 6.0 mg KOH g-1. The method may also be suitable for the determination of acidities outside of this range and for other classes of lubricants.

This specification covers an aluminum alloy in the form of die and hand forgings 6.000 inches (152.00 mm) and under in nominal thickness at time of heat treatment (see 8.6).