Search Results

The efforts of the ISO “Test Variability Task Force” have been aimed at improving the understanding and at reducing brake dynamometer test variability during performance testing. In addition, dynamometer test results have been compared and correlated to vehicle testing. Even though there is already a vast amount of anecdotal evidence confirming the fact that different procedures generate different friction coefficients on the same brake corner, the availability of supporting data to the industry has been elusive up to this point. To overcome this issue, this paper focuses on assessing friction levels, friction coefficient sensitivity, and repeatability under ECE, GB, ISO, JASO, and SAE laboratory friction evaluation tests.

Relative velocity detection thresholds of drivers are one factor that determines their ability to avoid rear-end crashes. Laboratory, simulator and driving studies show that drivers could scale relative velocity when it exceeded the threshold of about 0.003 rad/sec. Studies using accident reconstruction have suggested that the threshold may be about ten times larger. This paper discusses this divergence and suggests reasons for it and concludes that the lower value should be used as a true measure of the psychological threshold for detection of relative velocity.

A hybrid electric vehicle simulation tool (IBZ-Simulator) has been developed at the Fuel Cell Institute of the University of Applied Sciences Esslingen to study the fuel economy potential of a Fuel Cell hybrid urban bus. In this paper, the fundamental architecture of the FC urban buses was described, as well as the control strategy to manage the power flow between the different elements of the drive train. A comparison of the hybrid with the conventional type and ICE-hybrid type is performed, and important factors relating to the vehicle efficiency (accessory loads, vehicle mass, Fuel Cell system ramping rate and battery capacity) were assessed. The using of supercapacitor (or ultracapacitors) as peak power buffer has been investigated.

The Auto/Steel Partnership Corrosion Project Team has completed a perforation corrosion test program consisting of on-vehicle field exposures and various accelerated tests. Steel sheet products with eight combinations of metallic and organic coatings were tested, utilizing a simple crevice coupon design. On-vehicle exposures were conducted in St. John's and Detroit for up to seven years to establish a real-world performance standard. Identical test specimens were exposed to the various accelerated tests, and the results were compared to the real-world standard. This report documents the results of these tests, and compares the accelerated test results (including SAE J2334, GM9540P, Ford APGE, CCT-I, ASTM B117, South Florida Modified Volvo, and Kure Beach (25-meter) exposures) to the on-vehicle tests. The results are compared in terms of five criteria: extent of corrosion, rank order of material performance, degree of correlation, acceleration factor, and control of test environment.

This paper provides a review of the fatigue properties reported in the open literature for die cast magnesium-based alloys. Recently developed fatigue data, in the form of stress versus number of cycles to failure for bending fatigue (R=-1), are presented for die cast AM60B and AZ91D alloy specimens with thicknesses between 1 and 10 mm. The effects of specimen thickness and macrostructural features, such as porosity distributions and surface features (parting line and ejection pin marks), on the fatigue data are discussed.

There is an ongoing interest in biodegradable hydraulic fluids. Biodegradable fluids are often considered to include only vegetable oils, polyol esters and diester base stocks. However, other fluid base stocks including highly refined mineral oils, poly(alpha olefins) and fire-resistant fluids such as water-glycol hydraulic fluids are also biodegradable fluid alternatives. This paper will provide an overview of the international literature on biodegradable fluids, various international testing protocol, fluid base stocks, effect of oxidative stability, material compatibility and pump performance.

A second carbonyl round robin was conducted to enable participating laboratories doing routine analysis of carbonyls in vehicle exhaust emissions to assess their analytical capabilities. Three sets of solutions in acetonitrile containing varying number and amounts of standard DNPH-carbonyls were prepared. The parent carbonyls are known components of vehicle exhaust emissions. The samples were designed to challenge the capabilities of the participants to separate, identify and quantify all the components. The fourteen participating laboratories included automotive, contract, petroleum and regulatory organizations. All participants were able to separate and identify the C3 carbonyls; a few were not able to separate MEK from butyraldehyde and methacrolein from butyraldehyde; and many were not able to separate adequately the isomers of tolualdehyde. Inadequate separation and lack of appropriate standards resulted in a few misidentifications.

A brief overview of the history and scope of the SAE Oil Labeling Assessment Program is presented. Then, the results of analyses on 893 samples of engine oil purchased in the retail market over the first three years of the program, are discussed. All samples were labeled with the API SF or SG Service Category, separately, or in combination with an API “C” category designation. Additionally, 43 engine oil samples found to be questionably labeled, were repurchased and analyzed; these results are included.

This paper presents an overview of the Driver Performance Data Book under preparation by the National Highway Traffic Safety Administration (NHTSA). It includes a brief discussion of the purpose of the Data Book, the restrictions placed on the development effort, and how it is expected that it will be used by Agency personnel and others. Sample pages from the document are reproduced to illustrate the basic format, and the Table of Contents of each section is presented to identify the major topics covered and indicate the number of pages devoted to each.

The purpose of this paper is to survey the adverse environmental impacts resulting from motor vehicles, to review technologies developed to address these problems, and to summarize the current status of pollution control programs around the world.