Search Results

Polymer electrolyte membrane (PEM) fuel cells will play a crucial role in the decarbonization of the transport sector, in particular for heavy duty applications. However, performance and durability of PEMFC stacks is still a concern especially when operated under high power density conditions, as required in order to improve the compactness and to reduce the cost of the system. In this context, the optimization of the geometry of hydrogen and air distributors represents a key factor to improve the distribution of the reactants on the active surface, in order to guarantee a proper water management and avoiding membrane dehydration.

Composite materials are a natural choice for automotive applications where mechanical performance and lightweight are required. Nevertheless, attention should be directed to the defects into the material. This paper presents the building up of a Structural Health Monitoring system based on a piezoelectric transducers network: a continuous data system acquisition has been carried out in order to detect the presence of faults inside the analyzed structure. A piezoceramic patch has been coupled to a host structure in composite, to characterize the acquisition and the transmission of a wave signal on the material. The importance of this advanced technology research and the positive results obtained in the case study constitute the starting point for future application of piezoelectric-based Structural Health Monitoring systems over real industrial components.

Three different ceramic substrate materials (Silicon Carbide, Cordierite and Aluminum Titanate) for a Diesel Particulate Filter (DPF) for a European passenger car diesel engine have been experimentally investigated in this work. The filters were soot loaded under real world operating conditions on the road and then regenerated in two different ways that simulate the urban driving conditions, which are the most severe for DPF regeneration, since the low exhaust flow has a limited capability to absorb the heat generated by the soot combustion. The tests showed higher temperature peaks, at the same soot loading, for Cordierite and Aluminum Titanate compared to the Silicon Carbide, thus leading to a lower soot mass limit, which in turn required for these components a higher regeneration frequency with draw backs in terms of fuel consumption and lube oil dilution.

Molybdenum sulfide nanoparticles have been successfully obtained, for lubricant applications, by means of a wet chemical synthesis in an aqueous solution employing ammonium molybdate, citric acid and ammonium sulfide as the reactants. Some molybdenum-citrate complexes were formed and they reacted with the ammonium sulfide to form MoS₂ nanoparticles. Mo:citrate molar ratio was identified as being the most relevant of the synthesis parameters that affected the phase and morphology of the final products. The optimized nanopowders were softly agglomerated and amorphous, with a mean size of the primary particles of about 30 nm. The compatibility between the thus obtained MoS₂ nanopowders and some commercial after-treatment catalysts for diesel vehicle engines was tested. Diesel oxidation, soot combustion and ammonia-SCR de-NOx catalysts were considered as were the possible effects on the catalytic activity and their possible reaction to the MoS₂ additive.

It is well known that backpressure is one of the important parameters to be minimised during the exhaust system development. Unfortunately, during the first phases of an engineering process of a new engine, engine prototypes are not available yet. Due to this the exhaust system backpressure is generally evaluated using simulation software, and/or measuring the backpressure by a flow rig test at room temperature. Goal of this paper is to compare exhaust backpressure results obtained respectively: i) at the room temperature flow rig; ii) at the engine dyno bench; iii) by simulation with one of the most common 1D fluidodynamics simulation tool (Gt-Power). A correlation of the three different techniques is presented.

The paper deals with the Hardware-In-the-Loop based methodology which was adopted to evaluate the dynamic characteristics of Electronic Stability Program (ESP) and Electro-Hydraulic Brake (EHB) components. Firstly, it permits the identification of the time delays due to the hardware of the actuation system. Secondly, the link between the hardware of the hydraulic unit and a vehicle model running in real time permits the objective evaluation of the performance induced by the single components of different hydraulic units in terms of vehicle dynamics. The paper suggests the main parameters and tests which can help the car manufacturer in evaluating ESP hydraulic units, without expensive road tests.

The paper presents geometric, kinematic and fluid-dynamic modelling of variable displacement vane pumps for low pressure applications in internal combustion engines lubrication. All these fundamental aspects are integrated in a simulation environment and form the core of a design tool leading to the assessment of performance, critical issues, related influences and possible solutions in a well grounded engineering support to decision.

The paper presents geometric and kinematic aspects that constitute a premise to the modelling and simulation of gerotor lubricating oil pumps. With reference to a commercial oil pump two different modelling approaches of the pumping elements are addressed: the classical integral-derivative approach and the new derivative-integral approach. The latter, based on volumes swept by vector rays, is easier to implement and requires less computer time at equal accuracy. Two approaches to modelling are also detailed that feature different reticulations of the pump and consequently involve a different number of ordinary differential equations (ODE). Depending on the extent and detail of expected informations, either 4 or N+2 ODE must be solved, N being the number of variable volume chambers in the pump. Finally, numerical results of the simulation code, developed in the AMESim environment, have been compared with experimental results presented elsewhere [4].

This paper documents an extensive study aimed at a better understanding of the peculiarities and performance of crankshaft mounted gerotor pumps for IC engines lubrication. At different extents, the modelling, simulation and testing of a specific unit are all considered. More emphasis, at the modelling phase, is dedicated to the physical and mathematical description of the flow losses mechanisms; the often intricate aspects of kinematics being deliberately left aside. The pressure relief valve is analysed at a considerable extent as is the modelling of the working fluid, a typically aerated subsystem in such applications. Simulation is grounded on AMESim, a relatively novel tool in the fluid power domain, that proves effective and compliant with user deeds and objectives. Testing, at steady-state conditions, forms the basis for the pro!gressive tuning of the simulation model and provides significant insight into this type of volumetric pump.