Search Results

Abstract AISI H13 hot work tool steel is commonly used for applications such as hot forging and hot extrusion in mechanical working operations that face thermal and mechanical stress fluctuations, leading to premature failures. Cryogenic treatment was applied for AISI H13 steel to improve the surface hardness and thereby fatigue resistance. This work involves failure analysis of H13 steel specimens subjected to cryogenic treatment and gas nitriding. The specimens were heated to 1020°C, oil quenched followed by double tempering at 550°C for 2 h, and subsequently, deep cryogenically treated at −185°C in the cryochamber. Gas nitriding was carried out for 24 h at 500°C for 200 μm case depth in NH3 surroundings. The specimens were subjected to rotating bending fatigue at constant amplitude loading at room temperature.

Abstract The water droplet erosion (WDE) on high-speed rotating wheels appears in several engineering fields such as wind turbines, stationary steam turbines, fuel cell turbines, and turbochargers. The main reasons for this phenomenon are the high relative velocity difference between the colliding particles and the rotor, as well as the presence of inadequate material structure and surface parameters. One of the latest challenges in this area is the compressor wheels used in turbochargers, which has a speed up to 300,000 rpm and have typically been made of aluminum alloy for decades, to achieve the lowest possible rotor inertia. However, while in the past this component was only encountered with filtered air, nowadays, due to developments in compliance with tightening emission standards, various fluids also collide with the spinning blades, which can cause mechanical damage.

Abstract After a severe lane change, a wind gust, or another disturbance, the driver might be unable to recover the intended motion. Even though this fact is known by any driver, the scientific investigation and testing on this phenomenon is just at its very beginning, as a literature review, focusing on SAE Mobilus® database, reveals. We have used different mathematical models of car and driver for the basic description of car motion after a disturbance. Theoretical topics such as nonlinear dynamics, bifurcations, and global stability analysis had to be tackled. Since accurate mathematical models of drivers are still unavailable, a couple of driving simulators have been used to assess human driving action. Classic unstable motions such as Hopf bifurcations were found. Such bifurcations seem almost disregarded by automotive engineers, but they are very well-known by mathematicians. Other classic unstable motions that have been found are “unstable limit cycles.”

Abstract The use of appropriate loads and regulations is of great importance in weld fatigue assessment of rail on-track maintenance equipment and similar vehicles for optimized design. The regulations and available loads, however, are often generalized for several categories, which proves to be overly conservative for some specific categories of machines. EN (European Norm) and AAR (Association of American Railroads) regulations play a pivotal role in determining the applicable loads and acceptance criteria within this study. The availability of track-induced fatigue load data for the cumulative damage approach in track maintenance machines is often limited. Consequently, the FEA-based validation of rail track maintenance equipment often resorts to the infinite life approach rather than cumulative damage approach for track-induced travel loads, resulting in overly conservative designs.

Abstract All two-wheeler industries validate their product’s fatigue life on proving track before heading for mass production. Proving test tracks are made to simulate the end-user environment in order to find out the possible fatigue failures during each development stage of vehicle design, which in turn helps the CAE analysts to verify the design before it goes to the end-user hands. In this article we present the design and failure analysis of sub-frame assembly of motorbike observed during the accelerated fatigue test on proving track. Sub-frame main rod was found broken exactly between two weld endings during fatigue test before reaching 6% of the target fatigue life. Possible causes of sub-frame failures have been identified/analyzed in detail using fish bone diagram. A finite element analysis (FEA) model of sub-frame assembly was developed and a random response analysis was carried out on initial design.

Abstract The exponentially growing electrification market is driving demand for lithium-ion batteries (LIBs) with high performance. However, LIB thermal runaway events are one of the unresolved safety concerns. Thermal runaway of an individual LIB can cause a chain reaction of runaway events in nearby cells, or thermal propagation, potentially causing significant battery fires and explosions. Such a safety issue of LIBs raises a huge concern for a variety of applications including electric vehicles (EVs). With increasingly higher energy-density battery technologies being implemented in EVs to enable a longer driving mileage per charge, LIB safety enhancement is becoming critical for customers. This comprehensive review offers an encompassing overview of prevalent abuse conditions, the thermal event processes and mechanisms associated with LIBs, and various strategies for suppression, prevention, and mitigation.

Abstract This study investigated the influence of high-strength low-alloy steel on the fatigue life of a load-bearing member with a non-load-bearing transverse welded attachment (T-joint). It compared high cycle fatigue data to two fatigue design codes, namely BS 7608 and Eurocode EN 1993-1-9. Different base and filler material combinations of varying material strengths were investigated, resulting in a total of three different specimen configurations. Two material combinations had a high-strength steel (Strenx® 700 MC D) for the base material, with one combination having a matched filler material and the other having an undermatched filler material. The third material combination had a lower-strength steel (S 355 JR AR) for the base material, with a matched filler material. Tensile tests were performed to confirm the base material mechanical properties and weld quality of the manufactured specimens.

Abstract The cooperative platoon of multiple trucks with definite proximity has the potential to enhance traffic safety, improve roadway capacity, and reduce fuel consumption of the platoon. To investigate the truck platooning performance in a real-world environment, two Peterbilt class-8 trucks equipped with cooperative truck platooning systems (CTPS) were deployed to conduct the first-of-its-kind on-road commercial trial in Canada. A total of 41 CTPS trips were carried out on Alberta Highway 2 between Calgary and Edmonton during the winter season in 2022, 25 of which were platooning trips with 3 to 5 sec time gaps. The platooning trips were performed at ambient temperatures from −24 to 8°C, and the total truck weights ranged from 16 to 39 tons. The experimental results show that the average time gap error was 0.8 sec for all the platooning trips, and the trips with the commanded time gap of 5 sec generally had the highest variations.

Abstract Neutron diffraction is a powerful tool for noninvasive and nondestructive characterization of materials and can be applied even in large devices such as internal combustion engines thanks to neutrons’ exceptional ability to penetrate many materials. While proof-of-concept experiments have shown the ability to measure spatially and temporally resolved lattice strains in a small aluminum engine on a timescale of minutes over a limited spatial region, extending this capability to timescales on the order of a crank angle degree over the full volume of the combustion chamber requires careful design and optimization of the engine structure to minimize attenuation of the incident and diffracted neutrons to maximize count rates.

Abstract Currently, there is a growing tendency to incorporate natural fibers in composites due to their affordability, lightweight nature, and eco-friendliness. Researchers are continuously exploring new materials that offer improved mechanical properties for a broader range of applications. In this work, an experimental investigation on tensile and fatigue behavior of jute-wool felt-reinforced epoxy hybrid laminate is carried, in addition to an E-glass fiber-reinforced epoxy laminate that helps in comparison. Constant amplitude tensile fatigue test is conducted for 80%, 70%, and 60% of the ultimate load of respective composites at a stress ratio of 0.1 and frequency of 7 Hz for both laminates. The jute-wool felt composite showed good fatigue resistance. Though glass fiber composite showed higher tensile strength, jute-wool felt composite exhibits higher fatigue performance than glass fiber composites at higher stress levels.

Abstract The electrically interconnected suspension (EIS) is a novel suspension system that has gained attention due to its potential to improve vehicle vibration control. This article provides a comprehensive review of EIS and related technologies. It starts with an overview of the research on hydraulic interconnected suspension (HIS) and its limitations. Then, it discusses the development of the electromagnetic suspension (EMS) and its advantages in adjusting mechanical characteristics. The article focuses on the electrical network and decoupling control characteristics of EIS, demonstrating the principle of synchronous decoupling control of multiple vibration modes. A comparison of the structure and control characteristics of EIS and HIS highlights the advantages of EIS in vehicle vibration control.

Abstract Numerous researchers are committed to finding solutions to the path planning problem of intelligence-based vehicles. How to select the appropriate algorithm for path planning has always been the topic of scholars. To analyze the advantages of existing path planning algorithms, the intelligence-based vehicle path planning algorithms are classified into conventional path planning methods, intelligent path planning methods, and reinforcement learning (RL) path planning methods. The currently popular RL path planning techniques are classified into two categories: model based and model free, which are more suitable for complex unknown environments. Model-based learning contains a policy iterative method and value iterative method. Model-free learning contains a time-difference algorithm, Q-learning algorithm, state-action-reward-state-action (SARSA) algorithm, and Monte Carlo (MC) algorithm.

Abstract The exhaust manifold of a high-performance motorcycle engine is subjected to combined thermal and vibrational loadings. In this research, the whole fatigue assessment of an exhaust manifold is addressed. First, a classic low-cycle fatigue analysis is performed. Then, a specific methodology for determining the fatigue cycle of components subjected to thermal and vibration loadings is developed and presented in a way that possible damages can be evaluated. The results are post-processed and the damage caused by fatigue cycles is computed referring to the Wöhler curve of the material using the Dirlik approach.

Abstract ERRATUM

Abstract A comprehensive literature review of the optimization techniques used for the process parameter optimization of Abrasive Jet Machining (AJM), Ultrasonic Machining (USM), Laser Beam Machining (LBM), Electrochemical Machining (ECM), and Plasma Arc Machining (PAM) are presented in this review article. This review article is an extension of the review work carried out by previous researchers for the process parameter optimization of non-traditional machining processes using various advanced optimization algorithms. The review period considered for the same is from 2012 to 2022. The prime motive of this review article is to find out the sanguine effects of various optimization techniques used for the optimization of various considered objectives of selected non-traditional machining processes in addition to deemed materials and foremost process parameters.

Abstract The objective of the study was to evaluate the quasi-static and fatigue performance of automotive anti-roll bars (ARBs) under extreme environmental conditions. Flexural quasi-static and fatigue tests of SAE 1040 steel were conducted above and below the ductile-to-brittle transition temperature (DBTT) in flexure and compared with their room temperature performance. The flexural strength increased by decreasing the temperature to −40°C. The fatigue lives are determined for stress levels of 87%, 60%, and 30% of their flexural strength under displacement mode in constant amplitude loading. Experimental stress versus the number of cycles (S-N) curves of SAE 1040 steel state that all tube specimens have fatigue limits that were more than 100,000 cycles at −40°C. The fatigue life of the SAE 1040 tube exhibited infinite life below the ductile-to-brittle transition (DBT).

Abstract High-cycle fatigue (HCF) is one of the main concerns for spot-welded structures, and finite element (FE)-based simulations have critical importance for the life assessment and design optimization. The accuracy of spot weld modeling methodologies has a key role in achieving the development objectives. This article presents a comparative study for HCF simulations of different spot weld modeling methodologies and their comparison with the test data. In this regard, HCF analyses based on Findley’s multi-axial damage model are conducted with a commercial software. Direct equivalenced spot weld modeling with and without offset adjustment, rigid spot weld, and rigid beam (single) spot weld methods are analyzed for overlapped sheet metals under axial cyclic loading. Two specimens with different thicknesses, spot weld diameters, and number of nuggets are simulated under six cyclic load cases: 2000-4000 N, 1400-2800 N, 1800-3600 N, 200-8000 N, 100-8300 N, and 200-6800 N.

Abstract Fretting is a surface damage phenomenon and is typically observed at the contact interfaces such as bolted, gasketed joints, and the like. It occurs due to the combined effect of normal and tangential loads, which produces a small-amplitude relative sliding between two components that are held together using clamping forces. Fretting-related failures are also observed in multiple components of an internal combustion engine. This article presents the fretting fatigue damage evaluation of a single layer head gasket using a relative new approach, i.e., deviatoric strain amplitude-based method, further combined with the Ding’s empirical parameter D fret2. Corresponding fretting damage results are compared with the traditional approach based on the Ruiz’s parameter F1.

Abstract Enhancing the performance of a ride-oriented algorithm to provide ride comfort and vehicle stability throughout different terrains is a challenging task. This article aims to improve the performance of the state-of-the-art continuous skyhook algorithm in coupled motion modes with an optimally tuned stability augmentation system (SAS). The tuning process is carried out using a chaotic map-initialized particle swarm optimization (C-PSO) approach with ride comfort and roll stability as a performance index. A large van model built-in CarSim is co-simulated with a C-PSO algorithm and control system designed in MATLAB. To realize the feasibility and effectiveness of the proposed system, a software-in-loop test is conducted on five complex ride terrains with different dominant vehicle body motion modes. The test results are compared against the passive system, four corner continuous skyhook control, and four corner type-1 fuzzy control.

Abstract In the present study, the mechanical performances of plain carbon steel were explored based on the grain growth behavior. In the first step, the samples were normalized at different temperatures ranging from 900°C to 1100°C for 30, 60, 100, 150, and 200 min, respectively. In order to measure the grain size, the planimetric technique of Jeffries was used based on the optical micrographs taken for each sample. The mechanical properties of each grain such as hardness, elongation, yield, and tensile strength were studied, depending on the conventional methods. Experimental results showed that the increase in both heating temperature and holding time enhances grain growth, while the growth rate decreases with increasing time. The initial grain size and proportionality constant were calculated at 950°C, where K = 2.26 μm2/min and D 0 = 25.09 μm. Moreover, a significant increase in strength and hardness was observed with a decrease in grain size.