Search Results

Abstract Biogas (60% methane–40% CO2 approximately) can be used in the reactivity-controlled compression ignition (RCCI) mode along with a high-reactivity fuel (HRF). In this work dimethyl ether (DME) that can also be produced from renewable sources was used as the HRF as a move toward sustainable power generation. The two-cylinder turbocharged diesel engine modified to work in the DME–biogas RCCI (DMB-RCCI) mode was studied under different proportions of methane (45–95%) in biogas since the quality of this fuel can vary depending on the feedstock and production method. Only a narrow range of biogas to DME ratios could be tolerated in this mode at each output without misfire or knock. Detailed experiments were conducted at brake mean effective pressures (BMEPs) of 3 and 5 bar at a speed of 1500 rpm and comparisons were made with the diesel–biogas dual-fuel and diesel–biogas RCCI modes under similar methane flow rates while the proportion of CO2 was varied.

Abstract Driving schedule of every vehicle involves transient operation in the form of changing engine speed and load conditions, which are relatively unchanged during steady-state conditions. As well, the results from transient conditions are more likely to reflect the reality. So, the current research article is focused on analyzing the biofuel-like lemon peel oil (LPO) behavior under real-world transient conditions with fuel injection parameter MAP developed from steady-state experiments. At first, engine parameters and response MAPs are developed by using a response surface methodology (RSM)-based multi-objective optimization technique. Then, the vehicle model has been developed by incorporating real-world transient operating conditions. Finally, the developed injection parameters and response MAPs are embedded in the vehicle model to analyze the biofuel behavior under transient operating conditions.

Abstract NVH refinement of commercial vehicles is the key attribute for customer acceptance. Engine and road irregularities are the two major factors responsible for the same. During powertrain isolators’ design alone, the mass and inertia of the powertrain are usually considered, but in practical scenarios, a directly coupled subsystem also disturbs the boundary conditions for design. Due to the upgradation in emission norms, the exhaust aftertreatment system of modern automotive vehicles becomes heavier and more complex. This system is further coupled to the powertrain through a flexible joint or fixed joint, which results in the disturbance of the performance of the isolators. Therefore, to address this, the isolators design study is done by considering a multi-body dynamics model of vehicles with 16 DOF and 22 DOF problems, which is capable to simulate static and dynamic real-life events of vehicles.

Abstract Heavy-duty on-road engines are expected to conform to an ultralow NOx (ULNOx) standard of 0.027 g/kWh over the composite US heavy-duty transient federal test procedure (HD-FTP) cycle by 2031, a 90% reduction compared to 2010 emissions standards. Additionally, these engines are expected to conform to Phase 2 greenhouse gas regulations, which require tailpipe CO2 emissions under 579 g/kWh. This study experimentally demonstrates the ability of high fuel stratification gasoline compression ignition (HFS-GCI) to satisfy these emissions standards. Steady-state and transient tests are conducted on a prototype multi-cylinder heavy-duty GCI engine based on a 2010-compliant Cummins ISX15 diesel engine with a urea-SCR aftertreatment system (ATS). Steady-state calibration exercises are undertaken to develop highly fuel-efficient GCI calibration maps at both cold-start and warmed up conditions.

Abstract Improving thermal efficiency of an internal combustion engine is one of the most cost-effective ways to reduce life cycle-based CO2 emissions for transportation. Lean burn technology has the potential to reach high thermal efficiency if simultaneous low NOx, HC, and CO emissions can be achieved. Low NOx can be realized by ultra-lean (λ ≥ 2) spark-ignited combustion; however, the HC and CO emissions can increase due to slow flame propagation and high combustion variability. In this work, we introduce a new combustion concept called turbulent jet-controlled compression ignition, which utilizes multiple turbulent jets to ignite the mixture and subsequently triggers end gas autoignition. As a result, the ultra-lean combustion is further improved with reduced late-cycle combustion duration and enhanced HC and CO oxidation. A low-cost passive prechamber is innovatively fueled using a DI injector in the main combustion chamber through spray-guided stratification.

Abstract Reactivity-controlled compression ignition (RCCI) engine is an innovative dual-fuel strategy, which uses two fuels with different reactivity and physical properties to achieve low-temperature combustion, resulting in reduced emissions of oxides of nitrogen (NOx), particulate matter, and improved fuel efficiency at part-load engine operating conditions compared to conventional diesel engines. However, RCCI operation at high loads poses challenges due to the premixed nature of RCCI combustion. Furthermore, precise controls of indicated mean effective pressure (IMEP) and CA50 combustion phasing (crank angle corresponding to 50% of cumulative heat release) are crucial for drivability, fuel conversion efficiency, and combustion stability of an RCCI engine.

Abstract Despite the growing prominence of electrified vehicles, internal combustion engines remain essential in future transportation. This study delves into passive pre-chamber jet ignition, a leading-edge combustion technology, offering a comprehensive visualization of its operation under varying load and dilution conditions in light-duty GDI engines. Our primary objectives are to gain fundamental insights into passive pre-chamber jet ignition and subsequent main combustion processes and evaluate their response to different load and dilution conditions. We conducted experimental investigations using a light-duty, optical, single-cylinder engine equipped with three passive pre-chamber designs featuring varying nozzle diameters. Optical diagnostic imaging and heat release analysis provided critical insights.

Abstract Recent legislations require very low soot emissions downstream of the particulate filter in diesel vehicles. It will be difficult to meet the new more stringent OBD requirements with standard diagnostic methods based on differential sensors. The use of inexpensive and reliable soot sensors has become the focus of several academic and industrial works over the past decade. In this context, several diagnostic strategies have been developed to detect DPF malfunction based on the soot sensor loading time. This work proposes an advanced online diagnostic method based on soot sensor signal projection. The proposed method is model-free and exclusively uses soot sensor signal without the need for subsystem models or to estimate engine-out soot emissions. It provides a comprehensive and efficient filter monitoring scheme with light calibration efforts.

Abstract Limited fossil fuel resources and carbonaceous greenhouse gas emissions are two major problems the world faces today. Alternative fuels can effectively power internal combustion engines to address these issues. Methanol can be an alternative to conventional fuels, particularly to displace gasoline in spark ignition engines. The physicochemical properties of methanol are significantly different than baseline gasoline and fuel mixture-aim lambda; hence methanol-fueled engines require modifications in the fuel injection parameters. This study optimized the fuel injection quantity, spark timing, and air–fuel ratio for M85 (85% v/v methanol + 15% v/v gasoline) fueling of a port fuel-injected single-cylinder 500 cc motorcycle test engine. Comparative engine performance, combustion, and emissions analyses were performed for M85 and baseline gasoline.

Abstract Methanol is emerging as an alternate internal combustion engine fuel. It is getting attention in countries such as China and India as an emerging transport fuel. Using methanol in spark ignition engines is easier and more economical than in compression ignition engines via the blending approach. M85 (85% v/v methanol and 15% v/v gasoline) is one of the preferred blends with the highest methanol concentration. However, its physicochemical properties significantly differ from gasoline, leading to challenges in operating existing vehicles. This experimental study addresses the challenges such as cold-start operation and poor throttle response of M85-fueled motorcycle using a port fuel injection engine. In this study, M85-fueled motorcycle prototype is developed with superior performance, similar/better drivability, and lower emissions than a gasoline-fueled port-fuel-injected motorcycle.

Abstract The present study examines the effect of the multiple injection strategies in a common rail diesel engine using machine learning, image processing, and object detection techniques. The study demonstrates a novel approach of utilizing image-processing tools to gain information from heat release rates and in-cylinder visualizations from experimental or computational studies. The 3D CFD combustion and emission predictions of a commercial code ANSYS FORTE© are validated with small-bore common rail diesel engine data with known injection strategies. The validated CFD tool is used as a virtual plant model to optimize the injection schedule for reducing oxides of nitrogen (NOx) and soot emissions using an apparent heat release rate image-based machine learning tool. A methodology of the machine learning tool is quite helpful in predicting the NO–soot trade-off.

Abstract Pre-chamber jet ignition technologies have been garnering significant interest in the internal combustion engine field, given their potential to deliver shorter burn durations, increased combustion stability, and improved dilution tolerance. However, a clear understanding of the relationship between pre-chamber geometry, operating condition, jet formation, and engine performance in light-duty gasoline injection engines remains under-explored. Moreover, research specifically focusing on high dilution levels and passive pre-chambers with optical accessibility is notably scarce. This study serves to bridge these knowledge gaps by examining the influence of passive pre-chamber nozzle diameter and dilution level on jet formation and engine performance.

Abstract The development of a future hydrogen energy economy will require the development of several hydrogen market and industry segments including a hydrogen-based commercial freight transportation ecosystem. For a sustainable freight transportation ecosystem, the supporting fueling infrastructure and the associated vehicle powertrains making use of hydrogen fuel will need to be co-established. This article introduces the OR-AGENT (Optimal Regional Architecture Generation for Electrified National Transportation) tool developed at the Oak Ridge National Laboratory, which has been used to optimize the hydrogen refueling infrastructure requirements on the I-75 corridor for heavy-duty (HD) fuel cell electric commercial vehicles (FCEV).

Abstract Different platoon controls of connected automated vehicles have been studied to improve the entire fleet’s overall energy efficiency and driving safety. The platoons can be used during highway cruising to reduce unnecessary braking, shorten required headway, and thus improve traffic capacity and fuel economy. They can also be used in urban driving to improve traffic efficiency at intersections. However, there remain two problems that prevent the technology from achieving maximum benefit. First, the presence of human-driven vehicles will change the behavior of the fleet and platoon control of connected mixed traffic. Second, the communication uncertainties impose negative impacts on the dynamics of the platoon. A high-performance state predictor for surrounding vehicles can reduce the human-driven vehicle’s influence and help handle communication uncertainties better.

Abstract Biodiesel is a suitable alternative to diesel because of its carbon neutrality, renewability, lubricity, and lower pollutant emissions. However, extensive research indicates higher oxides of nitrogen (NOx) emissions with biodiesel. A practical method to combat this problem is utilizing water and biodiesel as emulsions. The effect of biodiesel-water emulsion in high-pressure fuel injection systems is not fully explored in the existing literature. The present study addresses this research gap by utilizing biodiesel-water emulsions in a modified light-duty diesel engine. The governor-controlled injection system was adapted to a fully flexible electronic system capable of high-pressure injection. Unlike other literature studies, the fuel injection timings were optimized with biodiesel-water emulsions to maximize brake thermal efficiency (bte) at every load condition.

Abstract Quantifying exhaust gas composition and temperature in vehicles with internal combustion engines (ICEs) is crucial to understanding and reducing emissions during transient engine operation. This is particularly important before the catalytic converter system lights off (i.e., during cold start). Most commercially available gas analyzers and temperature sensors are far too slow to measure these quantities on the timescale of individual cylinder-firing events, thus faster sensors are needed. A two-color mid-infrared (MIR) laser absorption spectroscopy (LAS) sensor for gas temperature and carbon monoxide (CO) mole fraction was developed and applied to address this technology gap. Two quantum cascade lasers (QCLs) were fiber coupled into one single-mode fiber to facilitate optical access in the test vehicle exhaust. The QCLs were time-multiplexed in order to scan across two CO absorption transitions near 2013 and 2060 cm–1 at 15 kHz.

Abstract Exhaust emission standards for road vehicles require on-board diagnostics (OBD) of all comprehensive powertrain components (CCMs) impacting pollutant emissions. The legislation defines the generic malfunction criteria and pollutant threshold limits to trigger the component functional degradation. The electric drivetrain in xEV (more than one propulsion energy converter) applications substitutes or supports the internal combustion engine (ICE) operation with electric machine (EM) power. Malfunctions in the electric drivetrain will lead to an increase in ICE power demand. Hence, the electric drive system is classified as a comprehensive component in the OBD legislation. The regulation defines monitoring of the EM performance. The malfunctions that could prevent the EM(s) from properly operating emission control strategies, including any ICE control activation or electric drivetrain performance degradation, should be monitored by the OBD system.

Abstract The development of efficient and reliable ignition systems for lean fuel-air mixtures is of great interest for applications associated with the use of combustion in transportation, electricity production, and other heavy industries. In this study, we report the use of repetitive nanosecond pulsed surface discharges for the ignition of lean methane (CH4)-air mixtures at pressures above 1 bar. Powered by ten 10-ns voltage pulses at 10 kHz, a commercially available non-resistive spark plug was used to generate surface discharges, which were able to ignite CH4-air mixtures at 1.5 bar and with equivalence ratios (ϕ) ranging from 1.0 to 0.5. At the leanest conditions, e.g., ϕ ≤ 0.6, nitric oxide (NO) and nitrogen dioxide (NO2) emission were reduced to <10% of their values at ϕ = 1.0, demonstrating the advantage of lean burn in emission reduction.

Abstract Lithium-ion batteries are the most crucial component of hybrid electric vehicles (HEVs) with respect to cost and performance. In this article, a new energy management strategy (EMS) is developed that improves fuel efficiency (FE) and suppresses the degradation of the battery. A hybridized two-layer algorithm that combines multi-objective nonlinear model predictive control (NMPC) with a rule-based (RB) algorithm is proposed as a new EMS that is called RB-NMPC. The RB-NMPC is designed to optimize the torque split between the engine and electric motors while maintaining the maximum and minimum constraints of each component. The proposed EMS is incorporated into control-oriented vehicle models, and their performances are analyzed for different driving cycles by comparing with RB, dynamic programming (DP), and NMPC.

Abstract The exhaust manifold of a high-performance motorcycle engine is subjected to combined thermal and vibrational loadings. In this research, the whole fatigue assessment of an exhaust manifold is addressed. First, a classic low-cycle fatigue analysis is performed. Then, a specific methodology for determining the fatigue cycle of components subjected to thermal and vibration loadings is developed and presented in a way that possible damages can be evaluated. The results are post-processed and the damage caused by fatigue cycles is computed referring to the Wöhler curve of the material using the Dirlik approach.