Refine Your Search

Date

Date

Commercial vehicles Education and training Vehicles, Equipment, and Performance MTC1, Earthmoving Machinery Automotive

Search Results

Viewing 1 to 18 of 18
1
Sort by published
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom
2011-12-08
CURRENT
J743_201112
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Rated Operating Load for Loaders Equipped with Log or Material Forks Without Vertical Mast
2011-10-27
CURRENT
J1197_201110
This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.
Standard

SPECIFICATION DEFINITIONS—LOADERS
1992-06-01
HISTORICAL
J732_199206
This SAE Standard provides uniform definitions of specification terms peculiar to loaders as defined in SAE J1057. The specifications must be qualified by stating the track shoe type, width or the tire type, size, ply, and specified inflation pressure; the model number or type of bucket disregarding teeth; and the type and amount of counterweight and/or ballast, if any, with which the machine is equipped. Paragraphs 4.1 to 4.16 are further defined by Figures 1 to 4. The figures are not intended to be exactly descriptive of any particular machine.
Standard

RATED OPERATING LOAD FOR LOADERS EQUIPPED WITH LOG OR MATERIAL FORKS WITHOUT VERTICAL MAST
1991-02-01
HISTORICAL
J1197_199102
This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.
Standard

COMPONENT NOMENCLATURE - DUMPERS
1990-07-30
HISTORICAL
J1016_199007
This SAE Standard provides names of major components peculiar to dumpers as defined in SAE J1057 (see Figure 1). Illustrations of components are not intended to be exactly descriptive of any particular machine. For component nomenclature for dumper trailers, refer to SAE J734.
Standard

COMPONENT NOMENCLATURE - DUMPER TRAILER
1990-07-01
HISTORICAL
J734_199007
See the following sections of SAE J1057 for machine identification: See SAE J1016 for additional component nomenclature.
Standard

COUNTERSUNK SQUARE HOLES FOR CUTTING EDGES AND END BITS
1986-07-01
HISTORICAL
J740_198607
To be used on cutting edges and end bits in conjunction with No. 3 head plow bolts (Ref. ANSI B18.9) typically used on off-road self-propelled work machines as described in SAE J1116. Cutting edges are further defined in SAE J737, J739 and J1304. End bits are further defined in SAE J63. 1 When section thickness exceeds A in drawing 1 (Figure 2) (countersunk one side) or B in drawing 4 (countersunk both sides), use counterbore with diameter D, as shown in cross section drawings 2, 5 and 6, or extended countersink C, as shown in cross section drawings 3 and 7. 2 The inscribed circle of the square holes shall be concentric with countersink or counterbore within 0.03 in (0.8 mm).
Standard

Hole Placement on Dozer End Bits
1986-05-01
HISTORICAL
J63_198605
It is the purpose of the SAE Recommended Practice to define the minimum requirements for hole placement on Dozer End Bit supports. The recommended practice applies to straight blade, angling blade, U blade, and semi-U blades used on earthmoving tractors per SAE J1057a up to a maximum weight of 100,000 lb (45,000 kg).
1
X