Refine Your Search

Date

Date

Computer simulation Commercial Vehicle Simulators Truck and Bus Wheel Committee Management and Organizations Fluid power systems

Search Results

Viewing 1 to 20 of 30
12Next >Last >>
Sort by published
Standard

ABS Exciter Ring Location Standardization
2023-10-02
CURRENT
J1730_202310
This SAE Recommended Practice establishes the antilock brake system (ABS) sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on or integral to the inboard end of spoke wheels, hubs, rotors, and hub-rotor assemblies on the following axle designations as defined in SAE J1842. a FF b FL c FC d FH e L f R g U h W j N k P
Standard

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus
2023-06-12
CURRENT
J1842_202306
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions - Truck and Bus
2023-05-19
CURRENT
J1671_202305
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
Standard

Wide Base Disc Wheels and Demountable Rims - Truck, Bus, and Trailer
2021-08-02
CURRENT
J876_202108
This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheel and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.
Standard

Dimensional Compatibility for Commercial Vehicles Fitment of Complete Wheels in Drum Brake Applications - Truck and Bus
2020-11-04
CURRENT
J1865_202011
This SAE Recommended Practice defines a clearance line for establishing dimensional compatibility between drum brakes and wheels with 19.5 inch, 22.5 inch, and 24.5 inch diameter rims. Wheels designed for use with drum brakes may not be suitable for disc brake applications. The lines provided establish the maximum envelope for brakes, including all clearances, and minimum envelope for complete wheels to allow for interchangeability. This document addresses the dimensional characteristics only, and makes no reference to the performance, operational dynamic deflections, or heat dissipation of the system. Valve clearances have not been included in the fitment lines. Bent valves may be required to clear brake drums. Disc brake applications may require additional running clearances beyond those provided by the minimum contour lines. Mounting systems as noted are referenced in SAE J694.
Standard

Dimension Compatibility for Commercial Vehicle Wheels to Air Disc Brake Calipers - Truck and Bus
2020-06-05
CURRENT
J2803_202006
This SAE Recommended Practice defines the boundary line for establishing dimensional compatibility between air disc brake calipers and 22.5 x 8.25 inch disc wheels, including bent valve stems on steel wheels and manufacturer recommended valve stems on aluminum wheels. The line establishes the minimum wheel with valve stem envelope to allow interchangeability. The line does not accommodate customer-specific wheels (such as OEM-specific stylized wheels) or customer-specific brakes. This document addresses dimensional characteristics only and makes no reference to the performance, operational dynamic deflections or heat dissipation of the system. It is up to the system integrator to ensure sufficient clearance exists between the caliper, wheel and valve stem to provide safe operating conditions. Mounting systems as noted are referenced in SAE J694.
Standard

Fastener Hardware for Wheels for Demountable Rims
2019-06-17
CURRENT
J1835_201906
This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims, wheels for demountable rims, rim spacers designed for 28 degrees bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. This document is divided into two sections. Section 1 establishes the practice for new designs for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document.
Standard

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus
2018-08-08
HISTORICAL
J1842_201808
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
Standard

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus
2014-02-03
HISTORICAL
J1842_201402
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
Standard

Fastener Hardware for Wheels for Demountable Rims
2014-01-03
HISTORICAL
J1835_201401
This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims, wheels for demountable rims, rim spacers designed for 28 degrees bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. This document is divided into two sections. Section 1 establishes the practice for new designs for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document.
Standard

Dimensions—Wheels for Demountable Rims, Demountable Rims, and Spacer Bands—Truck and Bus
2007-09-07
HISTORICAL
J851_200709
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rims, rim spacers, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
Standard

Wide Base Disc Wheels and Demountable Rims
2007-04-30
HISTORICAL
J876_200704
This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheels and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions—Truck and Bus
2006-05-22
HISTORICAL
J1671_200605
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. The geometric features described in this document are shown at true position. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
Standard

Wheel End Assembly and Axle Spindle Interface Dimensions—Truck and Bus
2005-03-21
HISTORICAL
J2475_200503
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, R, N and P. SAE configurations FC, K, L, U, and W are not included, but may be added in the future.
12Next >Last >>
X