Search Results

This work presents development and results of experimental and numerical investigations of an advanced ignition system with a scavenged pre-chamber for a natural gas fueled engine with a bore of 102 mm and stroke of 120 mm. Two combustion concepts are taken into account. The lean burn concept is used to minimize engine out emissions of nitric oxides (NOx) and to achieve high thermal efficiency at low load. The in-house designed scavenged pre-chamber enables the engine to be operated up to the air-excess ratio (lambda) of 2. A stoichiometric (lambda=1) operation is also possible. It is compatible with a three-way catalyst concept, at high load and potentially transient modes and can provide as high as possible engine power density. The influence of the scavenged pre-chamber volume on the combustion and performance within the range of the operational points of the naturally aspirated engine is presented in this paper.

Diesel knock and ringing combustion in compression ignition (CI) engines are largely an unavoidable phenomenon and are partially related to the overall effectiveness of the fuel injection process. Modern electronic fuel injection systems have been effective at reducing the intensity of knock in CI engines, largely through optimization of fuel injection timing, as well as higher operating pressures that promote enhanced fuel and air mixing. In this effort, a single-cylinder CI engine was tested under a number of different combustion strategies, including a comparison of mechanical and electronic injection systems, increasing fuel injection pressures for biodiesel fuels, and the usage of dual-fuel combustion with compressed natural gas (CNG). Using in-cylinder pressure traces and engine operational data, the difference in injection mechanisms, fuel preparation, and their effects on knock intensity is clearly illustrated.

Utilizing a higher compression ratio in a Compression Ignition (CI) engine grants an obvious advantage of improved thermal efficiency. However, the resulting combustion temperatures promote dissociation ensuing in increased nitrogen oxide (NOx) emissions. Unfortunately, due to the inherent properties of CI combustion, it is difficult to achieve simultaneous reduction of NOx and particulate matter (PM) through conventional combustion methods. Taking a different route though accomplishing Homogeneous Charge Compression Ignition (HCCI) in CI engines will largely eliminate NOx and PM; however, combustion can result in a significant increase in hydrocarbon (HC) and carbon monoxide (CO) emissions due to the low volatility of diesel fuel. Hence, this work attempts another avenue of Low Temperature Combustion (LTC) by employing Pre-mixed Charge Compression Ignition (PCI) combustion on a comparatively higher compression ratio (21.2) single cylinder CI engine.

The recent increase in natural gas availability has made compressed natural gas (CNG) an option for fueling the transportation sector of the United States economy. In particular, CNG is advantageous in dual-fuel operation alongside ultra low sulfur diesel (ULSD) for compression ignition (CI) engines. This work investigates the usage of natural gas mixtures at varying Energy Substitution Rates (ESRs) within a high compression ratio single-cylinder CI engine, including performance and heat release modeling of dual-fuel combustion. Results demonstrate the differing behavior of utilizing CNG at various substitution rates.

In this article the development of a combustion system with a fuel-scavenged pre-chamber is described. Such a system is commonly used in large-bore engines operated with extremely lean mixtures. The authors implemented the scavenged pre-chamber into a light duty truck-size engine with a bore of 102 mm. The lean burn strategy is intended to achieve very low nitrogen oxide (NOx) emissions at low load. At full load a stoichiometric mixture strategy is applied to achieve sufficient power density while simultaneously enabling the use of a relatively simple three-way catalytic converter for exhaust gas aftertreatment. This work outlines the pre-chamber design features and introduces the results of an experimental investigation of the effect of pre-chamber ignition on a single cylinder testing engine.

Given the need of the automotive industry to improve fuel efficiency, many companies are moving towards lean burn and low temperature combustion regimes. Critical control of these methods requires an accurate Exhaust Gas Recirculation (EGR) system that can maintain its desired rate and temperature. In this area, the literature illustrates different methodologies to control and monitor this EGR system; however, it lacks a discussion of how the non-linear nature of wave dynamics and time responses of an engine must be taken into account. In order to perform research into the use of EGR for these combustion regimes, an automated, closed-loop EGR system that uses a microprocessor to compute the slope change of the EGR rate and temperature as part of its feedback algorithm was constructed for use in a teaching and research laboratory. The findings illustrate that the system works as intended by replicating known combustion trends with EGR.

An ongoing research and development activities on the scavenged pre-chamber ignition system for an automotive natural gas fueled engine is presented in this paper. The experimental works have been performed in engine laboratory at steady state conditions on a gas engine with 102 mm bore and 120 mm stroke, converted to a single cylinder engine. The in-house designed scavenged pre-chamber is equipped with a spark plug, fuel supply and a miniature pressure sensor for detailed combustion diagnostics. The engine was operated at constant speed, fully open throttle valve and four different fueling modes with or without spark discharge. A partly motored mode allowed direct evaluation of the pre-chamber heat release. The experimental data acquired in this research served as a validation data for the numerical simulations. The performed tests of prototypes and calculations have recently been expanded to include 3-D flow calculations in the Ansys Fluent software.

This paper investigates the effect of the cetane number (CN) of a diesel fuel on the energy balance between a light duty (1.9L) and medium duty (4.5L) diesel engine. The two engines have a similar stroke to bore (S/B) ratio, and all other control parameters including: geometric compression ratio, cylinder number, stroke, and combustion chamber, have been kept the same, meaning that only the displacement changes between the engine platforms. Two Coordinating Research Council (CRC) diesel fuels for advanced combustion engines (FACE) were studied. The two fuels were selected to have a similar distillation profile and aromatic content, but varying CN. The effects on the energy balance of the engines were considered at two operating conditions; a “low load” condition of 1500 rev/min (RPM) and nominally 1.88 bar brake mean effective pressure (BMEP), and a “medium load” condition of 1500 RPM and 5.65 BMEP.

In-cylinder engine modeling is a necessary aspect of combustion research. In particular, simulating heat release connects variable combustion behavior to fuel properties through the 1st Law of Thermodynamics. One extension of such models is to evaluate changes to in-cylinder behavior using the Second Law of Thermodynamics in order to identify the peak period of availability for work extraction. Thus, Second Law models are a useful tool to augment research into alternative fuel usage and optimization. These models also help identify internal irreversibilities that are separate from heat transfer and exhaust gas losses. This study utilizes a multi-zone 1st and 2nd Law Heat Release model to characterize the changes in combustion behavior of a number of neat fuels used in a single-cylinder compression ignition (CI) engine.

Recently, ozone addition has come under scrutiny as a means of controlling ignition timing for Low Temperature (LTC) combustion, which defeats the NOx-PM tradeoff using a highly dilute, homogeneous mixture. This is because ozone decomposes into atomic oxygen and hydroxyl radicals that influence the early phases of the ignition delay process. In order to understand ozone's influence on combustion better, this work analyzes the effects of ozone-assisted combustion for a single-cylinder, direct-injection Compression Ignition engine via a mechanical pump-line-nozzle fuel system and an electronically controlled common-rail fuel injection system. Experimental outcomes indicate a relatively small influence of ozone for the mechanical injection system with a comparably decreased effect for the common rail system.

A key element to achieving vehicle emission certification for most light-duty vehicles using spark-ignition engine technology is prompt catalyst warming. Emission mitigation largely does not occur while the catalyst is below its “light-off temperature”, which takes a certain time to achieve when the engine starts from a cold condition. If the catalyst takes too long to light-off, the vehicle could fail its emission certification; it is necessary to minimize the catalyst warm up period to mitigate emissions as quickly as possible. One technique used to minimize catalyst warm up is to calibrate the engine in such a way that it delivers high temperature exhaust. At idle or low speed/low-load conditions, this can be done by retarding spark timing with a corresponding increase in fuel flow rate and / or leaning the mixture. Both approaches, however, encounter limits as combustion stability degrades and / or nitrogen oxide emissions rise excessively.

The first stage of ignition in saturated hydrocarbon fuels is characterized as low temperature heat release (LTHR) or cool flame combustion. LTHR takes place as a series of isomerization reactions at temperatures from 600K to 900K, and is often detectable in HCCI, rapid compression machines, and early injection low temperature combustion (LTC). The experimental investigation presented attempts to determine the behavior of LTHR in late injection low temperature combustion in a medium duty diesel as fuel varies and the influence of such behavior on LTC torque and emissions.

Significant progress towards reducing diesel engine fuel consumption and emissions is possible through the simultaneous Waste Heat Recovery (WHR) and Particulate Matter (PM) filtration in a novel device described here as a Diesel Particulate Filter Heat Exchanger (DPFHX). This original device concept is based on the shell-and-tube heat exchanger geometry, where enlarged tubes contain DPF cores, allowing waste heat recovery from engine exhaust and allowing further energy capture from the exothermic PM regeneration event. The heat transferred to the working fluid on the shell side of the DPFHX becomes available for use in a secondary power cycle, which is an increasingly attractive method of boosting powertrain efficiency due to fuel savings of around 10 to 15%. Moreover, these fuel savings are proportional to the associated emissions reduction after a short warm-up period, with startup emissions relatively unchanged when implementing a WHR system.

Engine manufacturers are considering the implementation of thermodynamic cycles for Waste Heat Recovery (WHR) in order to increase Internal Combustion Engine (ICE) system thermal efficiency. For these secondary cycles, the literature illustrates the preference of Organic Rankine Cycles (ORC's) due to its simplicity and efficient recovery of the medium grade waste heat found in engine exhaust. This paper simulates the heat recovery capacity of eight dry fluids (butane, pentane, hexane, cyclopentane, benzene, toluene, R245fa, and R123) for an ORC based on the exhaust from a single-cylinder diesel engine-generator operating under five different loading conditions. The model, developed using REFPROP and the Matlab Optimization Toolbox, represents the physical components using isentropic pump and expander efficiencies, along with two-zone heat exchangers. All fluids present cycle efficiencies between 10-15%, with the heaviest hydrocarbons generating the largest amount of work.

The use of exhaust gas recirculation (EGR) in internal combustion engines has significant impacts on combustion and emissions. EGR can be used to reduce in-cylinder NOx production, reduce emitted particulate matter, and enable advanced forms of combustion. To maximize the benefits of EGR, the exhaust gases are often cooled with on-engine liquid to gas heat exchangers. A common problem with this approach is the build-up of a fouling layer inside the heat exchanger due to thermophoresis and condensation, reducing the effectiveness of the heat exchanger in lowering gas temperatures. Literature has shown the effectiveness to initially drop rapidly and then approach steady state after a variable amount of time. The asymptotic behavior of the effectiveness has not been well explained. A range of theories have been proposed including fouling layer removal, changing fouling layer properties, and cessation of thermophoresis.

Research on dual-fuel engine systems is regaining interest as advances in combustion reveal enabling features for attaining high efficiencies. Although this movement is manifested by development of advanced modes of combustion (e.g., reactivity controlled compression ignition combustion, or RCCI), the possibility of gasoline / diesel conventional combustion exists, which is characterized by premixed gasoline and direct-injected diesel fuel at conventional diesel injection timing. This study evaluates the effects of operating parameter on fuel conversion efficiency for gasoline / diesel conventional combustion in a medium duty diesel engine. Through adjustment of gasoline ratio (mass basis), injection timing and rail pressure (with adjustments to diesel fuel quantity to hold torque constant), the combustion, performance and emissions are studied.

An experimental study is performed for homogeneous charge compression ignition (HCCI) combustion focusing on late phasing conditions with high cyclic variability (CV) approaching misfire. High CV limits the feasible operating range and the objective is to understand and quantify the dominating effects of the CV in order to enable controls for widening the operating range of HCCI. A combustion analysis method is developed for explaining the dynamic coupling in sequences of combustion cycles where important variables are residual gas temperature, combustion efficiency, heat release during re-compression, and unburned fuel mass. The results show that the unburned fuel mass carries over to the re-compression and to the next cycle creating a coupling between cycles, in addition to the well known temperature coupling, that is essential for understanding and predicting the HCCI behavior at lean conditions with high CV.

Conventional spark plugs ignite a fuel-air mixture via an electric-to-plasma energy transfer; the effectiveness of which can be described by an electric-to-plasma energy efficiency. Although conventional spark plug electric-to-plasma efficiencies have historically been viewed as adequate, it might be wondered how an increase in such an efficiency might translate (if at all) to improvements in the flame initiation period and eventual engine performance of a spark-ignition engine. A modification can be made to the spark plug that places a peaking capacitor in the path of the electrical current; upon coil energizing, the stored energy in the peaking capacitor substantially increases the energy delivered by the spark. A previous study has observed an improvement in the electric-to-plasma energy efficiency to around 50%, whereas the same study observed conventional spark plug electric-to-plasma energy efficiency to remain around 1%.

Premixed low temperature combustion (LTC) in diesel engines simultaneously reduces soot and NOx at the expense of increased hydrocarbon (HC) and CO emissions. The use of biodiesel in the LTC regime has been shown to produce lower HC emissions than petroleum diesel; however, unburned methyl esters from biodiesel are more susceptible to particulate matter (PM) formation following atmospheric dilution due to their low volatility. In this study, the efficacy of a production-type diesel oxidation catalyst (DOC) for the conversion of light hydrocarbons species and heavier, semi-volatile species like those in unburned fuel is examined. Experimental data were taken from a high speed direct-injection diesel engine operating in a mid-load, late injection partially premixed LTC mode on ultra-low sulfur diesel (ULSD) and neat soy-based biodiesel (B100). Gaseous emissions were recorded using a conventional suite of analyzers and individual light HCs were measured using an FT-IR analyzer.

Homogeneous charge compression ignition (HCCI) has received much attention in recent years due to its ability to reduce both fuel consumption and NO emissions compared to normal spark-ignited (SI) combustion. However, due to the limited operating range of HCCI, production feasible engines will need to employ a combination of combustion strategies, such as stoichiometric SI combustion at high loads and leaner burn spark-assisted compression ignition (SACI) and HCCI at intermediate and low loads. The goal of this study was to extend the high load limit of HCCI into the SACI region while maintaining a stoichiometric equivalence ratio. Experiments were conducted on a single-cylinder research engine with fully flexible valve actuation. In-cylinder pressure rise rates and combustion stability were controlled using cooled external EGR, spark assist, and negative valve overlap. Several engine loads within the SACI regime were investigated.