Search Results

It is widely understood that cold ambient temperatures negatively impact vehicle system efficiency. This is due to a combination of factors: increased friction (engine oil, transmission, and driveline viscous effects), cold start enrichment, heat transfer, and air density variations. Although the science of quantifying steady-state vehicle component efficiency is mature, transient component efficiencies over dynamic ambient real-world conditions is less understood and quantified. This work characterizes wheel assembly efficiencies of a conventional and electric vehicle over a wide range of ambient conditions. For this work, the wheel assembly is defined as the tire side axle spline, spline housing, bearings, brakes, and tires. Dynamometer testing over hot and cold ambient temperatures was conducted with a conventional and electric vehicle instrumented to determine the output energy losses of the wheel assembly in proportion to the input energy of the half-shafts.

Cylinder liner rotation (Rotating Liner Engine, RLE) is a new concept for reducing piston assembly friction in the internal combustion engine. The purpose of the RLE is to reduce or eliminate the occurrence of boundary and mixed lubrication friction in the piston assembly (specifically, the rings and skirt). This paper reports the results of experiments to quantify the potential of the RLE. A 2.3 L GM Quad 4 SI engine was converted to single cylinder operation and modified for cylinder liner rotation. To allow examination of the effects of liner rotational speed, the rotating liner is driven by an electric motor. A torque cell in the motor output shaft is used to measure the torque required to rotate the liner. The hot motoring method was used to compare the friction loss between the baseline engine and the rotating liner engine. Additionally, hot motoring tear-down tests were used to measure the contribution of each engine component to the total friction torque.

It is a very challenging problem to reliably ignite extremely lean mixtures, especially for the low speed, high load conditions of large-bore natural gas engines. If these engines are to be use for the distributed power generation market, it will require operation with higher boost pressures and even leaner mixtures. Both place greater demands on the ignition system. The railplug is a very promising ignition system for lean burn natural gas engines with its high-energy deposition and high velocity plasma arc. It requires care to properly design railplugs for this new application, however. For these engines, in-cylinder pressure and mixture temperature are very high at the time of ignition due to the high boost pressure. Hot spots may exist on the electrodes of the ignitor, causing pre-ignition problems. A heat transfer model is proposed in this paper to aid the railplug design. The electrode temperature was measured in an operating natural gas engine.

A liquid-phase port injection system for liquefied petroleum gas (LPG) generally consists of a fuel storage tank with extended capability of operating up to 600 psi, a fuel pump, and suitable fuel lines to and from the LPG fuel injectors mounted in the fuel rail manifold. Port injection of LPG in the liquid phase is attractive due to engine emissions and performance benefits. However, maintaining the LPG in the liquid phase at under-hood conditions and re-starting after hot soak can be difficult. Multiphase behavior within a liquid-phase LPG injection system was investigated computationally and experimentally. A commercial chemical equilibrium code (ASPEN PLUS™) was used to model various LPG compositions under operating conditions.

A quasidimensional engine simulation which uses the concepts of fractal geometry to model the effects of turbulence on flame propagation in a homogeneous charge SI engine has been developed. Heat transfer and blowby/crevice flow submodels are included in this code and the submodels chosen are found to be reasonable. The model predictions of cylinder pressure histories are then compared with experimental data over a range of loads, equivalence ratios, and engine speeds. The model is not adjusted in any manner to yield better agreement with the data, other than by tuning the simple turbulence model used so as to yield agreement with data for the nonreacting flow. However, current information about the flame wrinkling scales in an engine is inadequate. Therefore, predictions are made for three different assumptions about the flame wrinkling scales which span the range of physically possible scales.

This paper discusses the Formula SAE Student Engineering Design Competition that was held May 24-26, 1984. As was the case of previous student engineering design competitions, the purpose of the Formula SAE Competition is to enhance engineering education by requiring students to apply the technical knowledge gained in their coursework to a practical engineering design problem including choice of appropriate design criteria, design, fabrication, testing, and evaluation. For the Formula SAE Competition, the design problem chosen is to design, construct, and compete a low powered Formula type race car. The purpose of this paper is to describe the 1984 Formula SAE Competition and to present the results of this event. It is expected that this paper will serve as a guide to hosts of similar competitions and will aid future Formula SAE competitors.

This paper discusses the Formula SAE Student Engineering Design Competition that was held May 26-28, 1983. As was the case of previous student engineering design competitions, the purpose of the Formula SAE Competition is to enhance engineering education by requiring students to apply the technical knowledge gained in their coursework to a practical engineering design problem including choice of appropriate design criteria, design, fabrication, testing, and evaluation. For the Formula SAE Competition, the design problem chosen is to design, construct, and compete a low powered Formula type race car. The purpose of this paper is to describe the 1983 Formula SAE Competition and to present the results of this event. It is expected that this paper will serve as a guide to hosts of similar competitions and will aid future Formula SAE competitors.

This paper discusses the Formula SAE Student Engineering Design Competition that was held May 27–29, 1982. As was the case of previous student engineering design competitions, the purpose of the Formula SAE Competition is to enhance engineering education by requiring students to apply the technical knowledge gained in their coursework to a practical engineering design problem including choice of appropriate design criteria, design, fabrication, testing, and evaluation. For the Formula SAE Competition, the design problem chosen is to design, construct, and compete a low powered Indianapolis-type race car. The purpose of this paper is to describe the 1982 Formula SAE Competition and to present the results of this event. It is expected that this paper will serve as a guide to hosts of similar competitions and will aid future Formula SAE competitors.