Refine Your Search

Date

Date

Topic

Topic

Parts and Components Engine cooling systems Truck and Bus Powertrain Committee Bodies and Structures

Search Results

Viewing 1 to 20 of 45
123Next >Last >>
Sort by published
Standard

Torque Ratings for Power Take-off Mounting Pads
2017-09-19
CURRENT
J2662_201709
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
Standard

Recommended Remanufacturing Procedures for Manual Transmission Clutch Assemblies
2017-08-22
CURRENT
J1915_201708
This SAE Recommended Practice is prepared as a guideline to improve and maintain the quality of remanufactured automotive products. Installation of remanufactured or rebuilt products is often an economical way to repair a vehicle even though they may not fully be equivalent to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing, so as to provide durable operation of the part as well as acceptable performance when installed in a vehicle. The remanufacturer should also carefully consider the safety aspects of the product and any recommendations of the original manufacturer related to remanufacturing or rebuilding their product.
Standard

Manual Transmission Shift Patterns
2017-08-15
CURRENT
J1608_201708
Provide standard shift pattern guidelines for manual transmission shift controls in light, medium, and heavy trucks and buses.
Standard

Pilot Bearings for Truck and Bus Applications
2017-08-14
CURRENT
J1731_201708
This SAE Recommended Practice describes STANDARD-DUTY and EXTREME-DUTY Pilot Bearing requirements and sizes for class 6, 7, and 8 on-highway trucks and buses that use diesel engines and manual transmissions. The recommendations may apply to a wide range of other pilot-bearing applications, such as agricultural, industrial, and construction equipment.
Standard

SAE Nodal Mount
2017-08-14
CURRENT
J1134_201708
This SAE Recommended Practice establishes a single bolt pattern for the No. 1 clutch housing (see Figure 1) and the No. 2 clutch housing (see Figure 2). These four bolt patterns are designated to give commonality of mounting brackets in existing frame rails. The 420 mm (16.5 in) span, pad face to pad face, allows the ease of installation in existing frame rail widths. This is also the minimum spacing which will accommodate commonly used clutches.
Standard

Automotive Pull-Type Clutch Terminology
2012-11-09
CURRENT
J1479_201211
This SAE Standard describes the terms or names of the parts, characteristics, and parameters of automotive pull-type clutches used in trucks, and of vehicle apparatus or components related to the pull-type clutch.
Standard

Manual Transmission Shift Patterns
2012-11-09
HISTORICAL
J1608_201211
Provide standard shift pattern guidelines for manual transmission shift controls in light, medium, and heavy trucks and buses.
Standard

Nomenclature and Terminology for Truck and Bus Drive Axles
2012-07-02
CURRENT
J923_201207
This SAE Recommended Practice outlines basic nomenclature in common use for truck and bus drive axle designs. Over a period of years there have been many different designs introduced; however, for this report, only the most common have been selected and only their general construction is illustrated to show the nomenclature of the various parts.
Standard

Engine Retarder Dynamometer Test and Capability Rating Procedure
2005-12-12
HISTORICAL
J1621_200512
This SAE Recommended Practice has been adopted by SAE to specify: a A basis for net engine retarder power rating b Reference inlet air test conditions c A method for correcting observed engine retarder power to reference conditions d A method for determining net engine retarder power with a dynamometer
Standard

Torque Ratings for Power Take-off Mounting Pads
2003-07-25
HISTORICAL
J2662_200307
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
Standard

Manual Transmission Shift Patterns
2001-09-07
HISTORICAL
J1608_200109
Provide standard shift pattern guidelines for manual transmission shift controls in light, medium, and heavy trucks and buses.
Standard

Nomenclature and Terminology for Truck and Bus Drive Axles
2001-08-03
HISTORICAL
J923_200108
This SAE Recommended Practice outlines basic nomenclature in common use for truck and bus drive axle designs. Over a period of years there have been many different designs introduced; however, for this report, only the most common have been selected and only their general construction is illustrated to show the nomenclature of the various parts.
Standard

Pilot Bearings for Truck and Bus Applications
2001-06-12
HISTORICAL
J1731_200106
This SAE Recommended Practice describes STANDARD-DUTY and EXTREME-DUTY Pilot Bearing requirements and sizes for class 6, 7, and 8 on-highway trucks and buses that use diesel engines and manual transmissions. The recommendations may apply to a wide range of other pilot-bearing applications, such as agricultural, industrial, and construction equipment.
123Next >Last >>
X